Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2210.11644 · Optica

High-speed detection of 1550 nm single photons with superconducting nanowire detectors

Ioana Craiciu, Boris A. Korzh, Andrew D. Beyer, Andrew Mueller, Jason P. Allmaras, Lautaro Narváez, M. Spiropulu, Bruce Bumble, Thomas Lehner, Emma E. Wollman, Matthew D. Shaw

Published Dec 20, 2022• 82 citations
arXivHTMLPDF

Abstract

Superconducting nanowire single-photon detectors are a key technology for quantum information and science due to their high efficiency, low timing jitter, and low dark counts. In this work, we present a detector for single 1550 nm photons with up to 78% detection efficiency, timing jitter below 50 ps FWHM, 158 counts/s dark count rate, as well as a maximum count rate of 1.5 giga-counts/s at 3 dB compression. The PEACOQ detector (Performance-Enhanced Array for Counting Optical Quanta) comprises a linear array of 32 straight superconducting niobium nitride nanowires that span the mode of an optical fiber. This design supports high count rates with minimal penalties for detection efficiency and timing jitter. We show how these trade-offs can be mitigated by implementing independent readout for each nanowire and by using a temporal walk correction technique to reduce count-rate dependent timing jitter. These detectors make quantum communication practical on a 10 GHz clock.

DOI
10.1364/optica.478960

Related papers

Superconducting nanowire single-photon detectors at a wavelength of 940 nm

W. J. Zhang, Hao Li, Lixing You +9 more

We develop single-photon detectors comprising single-mode fiber-coupled superconducting nanowires, with high system detection efficiencies at a wavelength of 940 nm. The detector comprises a 6.5-nm-thick, 110-nm-wide NbN nanowire meander fabricated onto a Si substrate with a distributed Bragg reflector for enhancing the optical absorptance. We demonstrate that, via the design of a low filling factor (1/3) and active area (Φ = 10 μm), the system reaches a detection efficiency of ∼60% with a dark count rate of 10 Hz, a recovery time <12 ns, and a timing jitter of ∼50 ps.

arXiv:1506.07921•AIP Advances•Jun 1, 2015•7 citations

Broadband waveguide-integrated superconducting single-photon detectors with high system detection efficiency

Martin A. Wolff, Fabian Beutel, Jonas Schütte +4 more

Fast and efficient detection of single photons with high timing accuracy is a crucial requirement in most quantum optics experiments and enables novel sensing and imaging solutions. Superconducting nanowire single-photon detectors (SNSPD) achieve technology-leading performance in terms of detection efficiency, dark count rate, timing jitter, and detector dead times. However, conventional SNSPDs with high system detection efficiency typically rely on resonant enhancement of the absorption efficiency, thus only achieving attractive detector benchmarks over narrow spectral windows. Waveguide-integrated SNSPDs allow for leveraging the wideband material absorption in superconducting nanowires by absorbing light in a traveling-wave geometry but have been limited to low system detection efficiencies due to interface losses when coupling to optical fibers. Here, we show how high system detection efficiencies of 22%–73% are realized over a broad wavelength range from 532 nm to 1640 nm in a single waveguide-integrated SNSPD device. We accomplish efficient coupling between optical fibers and waveguide-integrated nanowire detectors by employing a 3D interface, produced in direct laser writing, that relies on total internal reflection for achieving a broad transmission bandwidth. We further find low timing jitter of 25.7 ps and detector decay times of 9.8 ns, allowing for single-photon counting with high repetition rates up to 100 MHz. Our work paves the way for an efficient single-photon detector solution that combines the spectral requirements of an extremely wide range of quantum optics experiments in a single device. The coupling approach and SNSPD-integration with nanophotonic circuits are further well-suited for realizing large-scale detector arrays.

Applied Physics Letters•Apr 12, 2021•48 citations

50 µm diameter superconducting nanowire single-photon detector with sub-17 ps timing jitter and high efficiency for visible wavelengths (Conference Presentation)

Jin Chang, Iman Esmaeil Zadeh

Superconducting nanowire single photon detectors (SNSPDs) have demonstrated advantages over traditional detectors in many fields [1]. Most fiber-coupled SNSPDs are coupled to single mode fibers, limiting their usability for applications where large surface area detectors are needed, for example fluorescence detection and satellite-based quantum communication [2][3]. Other important requirements for many applications are broadband detection efficiency, and low timing jitter [4]. So far, the increased meander length of multimode detectors, and the therefore increased kinetic inductance and number of imperfections due to film inhomogeneities have limited the timing jitter [5]. Moreover, combining low timing jitter with high detection efficiency and low dark count rate in one device is challenging due to the tradeoffs between different properties of SNSPDs [6]. In this paper, we achieved high efficiency and strong saturation over a broad wavelength range with a low timing jitter of 16.99 ps while maintaining a low dark count rate of < 0.2 Hz for an SNSPD coupled to a 50 µm core multimode fiber. To enhance the broadband absorption from 405 nm to 830 nm, detectors were fabricated on an optimized SiO2 cavity and Aluminum mirror. The geometry of the nanowire was also tuned to reach a good internal saturation of efficiency over the visible/NIR range but also to carry high current to get a large signal. Furthermore, a cryogenic readout amplifier was optimized to improve the signal to noise ratio and thus lead to high time resolution. Our devices can be readily used to enable higher resolution and faster quantum optics, bio-imaging, laser ranging and other optical experiments.

Quantum Optics and Photon Counting•May 13, 2019•0 citations

Waveguide integrated superconducting single-photon detectors with high internal quantum efficiency at telecom wavelengths

Oliver Kahl, Simone Ferrari, Vadim V. Kovalyuk +3 more

Superconducting nanowire single-photon detectors (SNSPDs) provide high efficiency for detecting individual photons while keeping dark counts and timing jitter minimal. Besides superior detection performance over a broad optical bandwidth, compatibility with an integrated optical platform is a crucial requirement for applications in emerging quantum photonic technologies. Here we present SNSPDs embedded in nanophotonic integrated circuits which achieve internal quantum efficiencies close to unity at 1550 nm wavelength. This allows for the SNSPDs to be operated at bias currents far below the critical current where unwanted dark count events reach milli-Hz levels while on-chip detection efficiencies above 70% are maintained. The measured dark count rates correspond to noise-equivalent powers in the 10(-19) W/Hz(-1/2) range and the timing jitter is as low as 35 ps. Our detectors are fully scalable and interface directly with waveguide-based optical platforms.

Scientific Reports•Jun 10, 2015•112 citations

High-speed and high-efficiency superconducting nanowire single photon detector array

Danna Rosenberg, Andrew J. Kerman, R. J. Molnar +1 more

Superconducting nanowire single photon detectors (SNSPDs) have separately demonstrated high efficiency, low noise, and extremely high speed when detecting single photons. However, achieving all of these simultaneously has been limited by detector subtleties and tradeoffs. Here, we report an SNSPD system with <80 ps timing resolution, kHz noise count rates, and 76% fiber-coupled system detection efficiency in the low-flux limit at 1550 nm. We present a model for determining the detection efficiency penalty due to the detection recovery time, and we validate our method using experimental data obtained at high count rates. We demonstrate improved performance tradeoffs, such as 68% system detection efficiency, including losses due to detector recovery time, when coupled to a Poisson source emitting 100 million photons per second. Our system can provide limited photon number resolution, continuous cryogen-free operation, and scalability to future imaging and GHz-count-rate applications.

Optics Express•Jan 14, 2013•190 citations

A superconducting nanowire single-photon detector system for single-photon source characterization

Catherine R. M. Fitzpatrick, Chandra M. Natarajan, Ryan E. Warburton +8 more

Single-photon sources and detectors are key enabling technologies for photonics in quantum information science and technology (QIST). QIST applications place high-level demands on the performance of sources and detectors; it is therefore essential that their properties can be characterized accurately. Superconducting nanowire single-photon detectors (SNSPDs) have spectral sensitivity from visible to beyond 2 μm in wavelength, picosecond timing resolution (Jitter <100 ps FWHM) and the capacity to operate ungated with low dark counts (<1 kHz). This facilitates data acquisition at high rates with an excellent signal-to-noise ratio. We report on the construction and characterization of a two-channel SNSPD system. The detectors are mounted in a closed-cycle refrigerator, which eliminates reliance on liquid cryogens. Our specification was to deliver a system with 1% efficiency in both channels at a wavelength of 1310 nm with 1 kHz dark count rate. A full width at half maximum timing jitter of less than 90 ps is achieved in both channels. The system will be used to detect individual photons generated by quantum-optical sources at telecom wavelengths. Examples include single-photon sources based on quantum dots (emitting at 1310 nm). The SNSPD system's spectral sensitivity and timing resolution make it suited to characterization of such sources, and to wider QIST applications.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Apr 20, 2010•0 citations
Superconducting nanowire single-photon detectors are a key technology for quantum information and science due to their high efficiency, low timing jitter, and low dark counts. In this work, we present a detector for single 1550 nm photons with up to 78% detection efficiency, timing jitter below 50 ps FWHM, 158 counts/s dark count rate, as well as a maximum count rate of 1.5 giga-counts/s at 3 dB compression. The PEACOQ detector (Performance-Enhanced Array for Counting Optical Quanta) comprises a linear array of 32 straight superconducting niobium nitride nanowires that span the mode of an optical fiber. This design supports high count rates with minimal penalties for detection efficiency and timing jitter. We show how these trade-offs can be mitigated by implementing independent readout for each nanowire and by using a temporal walk correction technique to reduce count-rate dependent timing jitter. These detectors make quantum communication practical on a 10 GHz clock.
We develop single-photon detectors comprising single-mode fiber-coupled superconducting nanowires, with high system detection efficiencies at a wavelength of 940 nm. The detector comprises a 6.5-nm-thick, 110-nm-wide NbN nanowire meander fabricated onto a Si substrate with a distributed Bragg reflector for enhancing the optical absorptance. We demonstrate that, via the design of a low filling factor (1/3) and active area (Φ = 10 μm), the system reaches a detection efficiency of ∼60% with a dark count rate of 10 Hz, a recovery time <12 ns, and a timing jitter of ∼50 ps.
Fast and efficient detection of single photons with high timing accuracy is a crucial requirement in most quantum optics experiments and enables novel sensing and imaging solutions. Superconducting nanowire single-photon detectors (SNSPD) achieve technology-leading performance in terms of detection efficiency, dark count rate, timing jitter, and detector dead times. However, conventional SNSPDs with high system detection efficiency typically rely on resonant enhancement of the absorption efficiency, thus only achieving attractive detector benchmarks over narrow spectral windows. Waveguide-integrated SNSPDs allow for leveraging the wideband material absorption in superconducting nanowires by absorbing light in a traveling-wave geometry but have been limited to low system detection efficiencies due to interface losses when coupling to optical fibers. Here, we show how high system detection efficiencies of 22%–73% are realized over a broad wavelength range from 532 nm to 1640 nm in a single waveguide-integrated SNSPD device. We accomplish efficient coupling between optical fibers and waveguide-integrated nanowire detectors by employing a 3D interface, produced in direct laser writing, that relies on total internal reflection for achieving a broad transmission bandwidth. We further find low timing jitter of 25.7 ps and detector decay times of 9.8 ns, allowing for single-photon counting with high repetition rates up to 100 MHz. Our work paves the way for an efficient single-photon detector solution that combines the spectral requirements of an extremely wide range of quantum optics experiments in a single device. The coupling approach and SNSPD-integration with nanophotonic circuits are further well-suited for realizing large-scale detector arrays.
Superconducting nanowire single photon detectors (SNSPDs) have demonstrated advantages over traditional detectors in many fields [1]. Most fiber-coupled SNSPDs are coupled to single mode fibers, limiting their usability for applications where large surface area detectors are needed, for example fluorescence detection and satellite-based quantum communication [2][3]. Other important requirements for many applications are broadband detection efficiency, and low timing jitter [4]. So far, the increased meander length of multimode detectors, and the therefore increased kinetic inductance and number of imperfections due to film inhomogeneities have limited the timing jitter [5]. Moreover, combining low timing jitter with high detection efficiency and low dark count rate in one device is challenging due to the tradeoffs between different properties of SNSPDs [6]. In this paper, we achieved high efficiency and strong saturation over a broad wavelength range with a low timing jitter of 16.99 ps while maintaining a low dark count rate of < 0.2 Hz for an SNSPD coupled to a 50 µm core multimode fiber. To enhance the broadband absorption from 405 nm to 830 nm, detectors were fabricated on an optimized SiO2 cavity and Aluminum mirror. The geometry of the nanowire was also tuned to reach a good internal saturation of efficiency over the visible/NIR range but also to carry high current to get a large signal. Furthermore, a cryogenic readout amplifier was optimized to improve the signal to noise ratio and thus lead to high time resolution. Our devices can be readily used to enable higher resolution and faster quantum optics, bio-imaging, laser ranging and other optical experiments.
Superconducting nanowire single-photon detectors (SNSPDs) provide high efficiency for detecting individual photons while keeping dark counts and timing jitter minimal. Besides superior detection performance over a broad optical bandwidth, compatibility with an integrated optical platform is a crucial requirement for applications in emerging quantum photonic technologies. Here we present SNSPDs embedded in nanophotonic integrated circuits which achieve internal quantum efficiencies close to unity at 1550 nm wavelength. This allows for the SNSPDs to be operated at bias currents far below the critical current where unwanted dark count events reach milli-Hz levels while on-chip detection efficiencies above 70% are maintained. The measured dark count rates correspond to noise-equivalent powers in the 10(-19) W/Hz(-1/2) range and the timing jitter is as low as 35 ps. Our detectors are fully scalable and interface directly with waveguide-based optical platforms.
Superconducting nanowire single photon detectors (SNSPDs) have separately demonstrated high efficiency, low noise, and extremely high speed when detecting single photons. However, achieving all of these simultaneously has been limited by detector subtleties and tradeoffs. Here, we report an SNSPD system with <80 ps timing resolution, kHz noise count rates, and 76% fiber-coupled system detection efficiency in the low-flux limit at 1550 nm. We present a model for determining the detection efficiency penalty due to the detection recovery time, and we validate our method using experimental data obtained at high count rates. We demonstrate improved performance tradeoffs, such as 68% system detection efficiency, including losses due to detector recovery time, when coupled to a Poisson source emitting 100 million photons per second. Our system can provide limited photon number resolution, continuous cryogen-free operation, and scalability to future imaging and GHz-count-rate applications.
Single-photon sources and detectors are key enabling technologies for photonics in quantum information science and technology (QIST). QIST applications place high-level demands on the performance of sources and detectors; it is therefore essential that their properties can be characterized accurately. Superconducting nanowire single-photon detectors (SNSPDs) have spectral sensitivity from visible to beyond 2 μm in wavelength, picosecond timing resolution (Jitter <100 ps FWHM) and the capacity to operate ungated with low dark counts (<1 kHz). This facilitates data acquisition at high rates with an excellent signal-to-noise ratio. We report on the construction and characterization of a two-channel SNSPD system. The detectors are mounted in a closed-cycle refrigerator, which eliminates reliance on liquid cryogens. Our specification was to deliver a system with 1% efficiency in both channels at a wavelength of 1310 nm with 1 kHz dark count rate. A full width at half maximum timing jitter of less than 90 ps is achieved in both channels. The system will be used to detect individual photons generated by quantum-optical sources at telecom wavelengths. Examples include single-photon sources based on quantum dots (emitting at 1310 nm). The SNSPD system's spectral sensitivity and timing resolution make it suited to characterization of such sources, and to wider QIST applications.