Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2208.06764 · Optics Express

Triply-resonant sum frequency conversion with gallium phosphide ring resonators

Alan D. Logan, Shivangi Shree, Srivatsa Chakravarthi, Nicholas Yama, Christian Pederson, Karine Hestroffer, Fariba Hatami, Kai‐Mei C. Fu

Published Dec 20, 2022• 23 citations
arXivHTMLPDF

Abstract

We demonstrate quasi-phase matched, triply-resonant sum frequency conversion in 10.6-µm-diameter integrated gallium phosphide ring resonators. A small-signal, waveguide-to-waveguide power conversion efficiency of 8 ± 1.1%/mW; is measured for conversion from telecom (1536 nm) and near infrared (1117 nm) to visible (647 nm) wavelengths with an absolute power conversion efficiency of 6.3 ± 0.6%; measured at saturation pump power. For the complementary difference frequency generation process, a single photon conversion efficiency of 7.2%/mW from visible to telecom is projected for resonators with optimized coupling. Efficient conversion from visible to telecom will facilitate long-distance transmission of spin-entangled photons from solid-state emitters such as the diamond NV center, allowing long-distance entanglement for quantum networks.

DOI
10.1364/oe.473211

Related papers

Proposal for noise-free visible-telecom quantum frequency conversion through third-order sum and difference frequency generation

Xiyuan Lu, Gregory T. Moille, Ashutosh Rao +1 more

Quantum frequency conversion (QFC) between the visible and telecom is a key to connect quantum memories in fiber-based quantum networks. Current methods for linking such widely separated frequencies, such as sum/difference frequency generation and four-wave mixing Bragg scattering, are prone to broadband noise generated by the pump laser(s). To address this issue, we propose to use third-order sum/difference frequency generation (TSFG/TDFG) for an upconversion/downconversion QFC interface. In this process, two long wavelength pump photons combine their energy and momentum to mediate frequency conversion across the large spectral gap between the visible and telecom bands, which is particularly beneficial from the noise perspective. We show that waveguide-coupled silicon nitride microring resonators can be designed for efficient QFC between 606 and 1550 nm via a 1990 nm pump through TSFG/TDFG. We simulate the device dispersion and coupling, and from the simulated parameters, estimate that the frequency conversion can be efficient (${\gt}80 \%$) at 50 mW pump power. Our results suggest that microresonator TSFG/TDFG is promising for compact, scalable, and low-power QFC across large spectral gaps.

arXiv:2010.06811•Optics Letters•Dec 7, 2020•11 citations

Highly efficient visible and near-IR photon pair generation with thin-film lithium niobate

Nathan Harper, Emily Hwang, Ryoto Sekine +4 more

Efficient on-chip entangled photon pair generation at telecom wavelengths is an integral aspect of emerging quantum optical technologies, particularly for quantum communication and computing. However, moving to shorter wavelengths enables the use of more accessible silicon detector technology, and opens up applications in imaging and spectroscopy. Here, we present high brightness ((1.6 ± 0.3) × 10 9 pairs/s/mW/nm) visible–near-IR photon pair generation in a periodically poled lithium niobate nanophotonic waveguide. The degenerate spectrum of the photon pairs is centered at 811 nm with a bandwidth of 117 nm when pumped with a spectrally multimode laser diode. The measured on-chip source efficiency of (2.3 ± 0.5) × 10 11 pairs/s/mW is on par with source efficiencies at telecom wavelengths and is also orders of magnitude higher than the efficiencies of other visible sources implemented in bulk crystal or diffused waveguide-based technologies. Further improvements in the brightness and efficiencies are possible by pumping the device with a single-frequency laser, which would also shrink the pair bandwidth. These results represent the shortest wavelength of photon pairs generated in a nanophotonic waveguide reported to date by nearly an octave.

arXiv:2310.07046•Optica Quantum•Mar 6, 2024•28 citations

Visible-Telecom Entangled-Photon Pair Generation with Integrated Photonics: Guidelines and a Materials Comparison

Liao Duan, Trevor J. Steiner, Paolo Pintus +4 more

Correlated photon-pair sources are key components for quantum computing, networking, synchronization, and sensing applications. Integrated photonics has enabled chip-scale sources using nonlinear processes, producing high-rate time-energy and polarization entanglement at telecom wavelengths with sub-100 microwatt pump power. Many quantum systems operate in the visible or near-infrared ranges, necessitating visible-telecom entangled-pair sources for connecting remote systems via entanglement swapping and teleportation. This study evaluates biphoton pair generation and time-energy entanglement through spontaneous four-wave mixing in various nonlinear integrated photonic materials, including silicon nitride, lithium niobate, aluminum gallium arsenide, indium gallium phosphide, and gallium nitride. We demonstrate how geometric dispersion engineering facilitates phase-matching for each platform and reveals unexpected results, such as robust designs to fabrication variations and a Type-1 cross-polarized phase-matching condition for III-V materials that expands the operational wavelength range.

arXiv:2407.04792•ACS Photonics•Nov 25, 2024•11 citations

High-Efficiency Broadband Near-Infrared Single-Photon Frequency Upconversion and Detection*

Jianhui Ma, Huiqin Hu, Yu Chen +3 more

We propose and demonstrate a high efficiency broadband near infrared single-photon upconversion and detection with a broadband pump laser based on sum frequency conversion in the PPLN crystal. By using a pump laser centered at 1040 nm with a spectral bandwidth of 10 nm, the signal single-photons centered at 1562 nm with a broadband bandwidth up to 7.2 nm are frequency-converted from the near infrared to the visible regime. A maximum conversion efficiency of 18.8% is achieved, while the background noise is measured to be only 1.2 × 10−3 counts/pulse. The corresponding spectral linewidth of the upconverted photons is 0.2 nm. This scheme of broadband infrared single-photon upconversion and detection provides potential solutions in infrared laser ranging, broadband infrared imaging and quantum key distribution.

Chinese Physics Letters•Mar 1, 2020•3 citations

Single-photon frequency conversion for quantum interface

Tong Xiang, Yuanlin Zheng, Yuanhua Li +1 more

Single-photon frequency conversion for quantum interface plays an important role in quantum communications and networks, which is crucial for the realization of quantum memory, faithful entanglement swapping and quantum teleportation. In this talk, I will present our recent experiments about single-photon frequency conversion based on quadratic nonlinear processes. Firstly, we demonstrated spectrum compression of broadband single photons at the telecom wavelength to the near-visible window. A positively chirped single-photon-level laser pulse and a negatively chirped classical one are converted to a narrowband single-photon pulse, with a spectrum compression factor of 58, through sum-frequency generation (SFG), marking a critical step towards coherent photonic interface. Secondly, we demonstrated the nonlinear interaction between two chirped broadband single-photon-level coherent states. A high SFG efficiency of 1.06 × 10−7 is realized, which may be utilized to achieve heralding entanglement at a distance. Finally, we theoretically introduced and experimentally demonstrated single-photon frequency conversion in the telecom band, enabling switching of single photons between dense wavelength-division multiplexing channels. Using cascaded quasi-phase matched sum/difference frequency generation, the signal photon of a photon pair from spontaneous down-conversion is precisely shifted to identically match its counterpart, i.e. idler photon, in frequency to manifest a clear non-classical dip in the Hong-Ou-Mandel interference. Moreover, quantum entanglement between the photon pair is maintained after the frequency conversion. Our researches have realized three significant quantum interfaces via single-photon frequency conversion, which hold great promise for the development of quantum communications and networks.

SPIE Conference on Quantum and Nonlinear Optics•Nov 14, 2018•0 citations

Fiber-integrated Quantum Frequency Conversion for Long-distance Quantum Networking

Zhichuan Liao, Ao Shen, Lai Zhou +2 more

Signal photons emitted by quantum nodes typically fall outside the low-loss telecom window of optical fibers, leading to severe transmission losses. Quantum frequency conversion (QFC) offers an effective optical interface that bridges quantum nodes with telecom-band channels, enabling long-distance quantum communication. In this work, we demonstrate a compact, fiber-integrated QFC system with low noise and a high signal-to-noise ratio (SNR). Using a periodically poled lithium niobate (PPLN) waveguide, input photons at 637.2 nm are down-converted to telecom photons at 1588.3 nm. Our system achieves a total conversion efficiency of approximately 9%, with pump-induced noise suppressed to 154 Hz. For input photon rates of 32.7, 118.0, and 327.7 kHz, the corresponding SNRs are 12.3, 43.9, and 117.8, respectively. We further develop a theoretical model to simulate the entanglement fidelity between nitrogen-vacancy (NV) center spins and the frequency-converted telecom photons. At the emission rate of an NV center, our QFC system maintains an expected fidelity exceeding 52% over a transmission distance of 100 km. These findings highlight the potential of our QFC system for scalable, long-distance quantum networking.

quant-pharXiv:2604.23444•npj Quantum Information•Apr 28, 2026•0 citations
We demonstrate quasi-phase matched, triply-resonant sum frequency conversion in 10.6-µm-diameter integrated gallium phosphide ring resonators. A small-signal, waveguide-to-waveguide power conversion efficiency of 8 ± 1.1%/mW; is measured for conversion from telecom (1536 nm) and near infrared (1117 nm) to visible (647 nm) wavelengths with an absolute power conversion efficiency of 6.3 ± 0.6%; measured at saturation pump power. For the complementary difference frequency generation process, a single photon conversion efficiency of 7.2%/mW from visible to telecom is projected for resonators with optimized coupling. Efficient conversion from visible to telecom will facilitate long-distance transmission of spin-entangled photons from solid-state emitters such as the diamond NV center, allowing long-distance entanglement for quantum networks.
Quantum frequency conversion (QFC) between the visible and telecom is a key to connect quantum memories in fiber-based quantum networks. Current methods for linking such widely separated frequencies, such as sum/difference frequency generation and four-wave mixing Bragg scattering, are prone to broadband noise generated by the pump laser(s). To address this issue, we propose to use third-order sum/difference frequency generation (TSFG/TDFG) for an upconversion/downconversion QFC interface. In this process, two long wavelength pump photons combine their energy and momentum to mediate frequency conversion across the large spectral gap between the visible and telecom bands, which is particularly beneficial from the noise perspective. We show that waveguide-coupled silicon nitride microring resonators can be designed for efficient QFC between 606 and 1550 nm via a 1990 nm pump through TSFG/TDFG. We simulate the device dispersion and coupling, and from the simulated parameters, estimate that the frequency conversion can be efficient (>80%{\gt}80 \%>80%) at 50 mW pump power. Our results suggest that microresonator TSFG/TDFG is promising for compact, scalable, and low-power QFC across large spectral gaps.
Efficient on-chip entangled photon pair generation at telecom wavelengths is an integral aspect of emerging quantum optical technologies, particularly for quantum communication and computing. However, moving to shorter wavelengths enables the use of more accessible silicon detector technology, and opens up applications in imaging and spectroscopy. Here, we present high brightness ((1.6 ± 0.3) × 10 9 pairs/s/mW/nm) visible–near-IR photon pair generation in a periodically poled lithium niobate nanophotonic waveguide. The degenerate spectrum of the photon pairs is centered at 811 nm with a bandwidth of 117 nm when pumped with a spectrally multimode laser diode. The measured on-chip source efficiency of (2.3 ± 0.5) × 10 11 pairs/s/mW is on par with source efficiencies at telecom wavelengths and is also orders of magnitude higher than the efficiencies of other visible sources implemented in bulk crystal or diffused waveguide-based technologies. Further improvements in the brightness and efficiencies are possible by pumping the device with a single-frequency laser, which would also shrink the pair bandwidth. These results represent the shortest wavelength of photon pairs generated in a nanophotonic waveguide reported to date by nearly an octave.
Correlated photon-pair sources are key components for quantum computing, networking, synchronization, and sensing applications. Integrated photonics has enabled chip-scale sources using nonlinear processes, producing high-rate time-energy and polarization entanglement at telecom wavelengths with sub-100 microwatt pump power. Many quantum systems operate in the visible or near-infrared ranges, necessitating visible-telecom entangled-pair sources for connecting remote systems via entanglement swapping and teleportation. This study evaluates biphoton pair generation and time-energy entanglement through spontaneous four-wave mixing in various nonlinear integrated photonic materials, including silicon nitride, lithium niobate, aluminum gallium arsenide, indium gallium phosphide, and gallium nitride. We demonstrate how geometric dispersion engineering facilitates phase-matching for each platform and reveals unexpected results, such as robust designs to fabrication variations and a Type-1 cross-polarized phase-matching condition for III-V materials that expands the operational wavelength range.
We propose and demonstrate a high efficiency broadband near infrared single-photon upconversion and detection with a broadband pump laser based on sum frequency conversion in the PPLN crystal. By using a pump laser centered at 1040 nm with a spectral bandwidth of 10 nm, the signal single-photons centered at 1562 nm with a broadband bandwidth up to 7.2 nm are frequency-converted from the near infrared to the visible regime. A maximum conversion efficiency of 18.8% is achieved, while the background noise is measured to be only 1.2 × 10−3 counts/pulse. The corresponding spectral linewidth of the upconverted photons is 0.2 nm. This scheme of broadband infrared single-photon upconversion and detection provides potential solutions in infrared laser ranging, broadband infrared imaging and quantum key distribution.
Single-photon frequency conversion for quantum interface plays an important role in quantum communications and networks, which is crucial for the realization of quantum memory, faithful entanglement swapping and quantum teleportation. In this talk, I will present our recent experiments about single-photon frequency conversion based on quadratic nonlinear processes. Firstly, we demonstrated spectrum compression of broadband single photons at the telecom wavelength to the near-visible window. A positively chirped single-photon-level laser pulse and a negatively chirped classical one are converted to a narrowband single-photon pulse, with a spectrum compression factor of 58, through sum-frequency generation (SFG), marking a critical step towards coherent photonic interface. Secondly, we demonstrated the nonlinear interaction between two chirped broadband single-photon-level coherent states. A high SFG efficiency of 1.06 × 10−7 is realized, which may be utilized to achieve heralding entanglement at a distance. Finally, we theoretically introduced and experimentally demonstrated single-photon frequency conversion in the telecom band, enabling switching of single photons between dense wavelength-division multiplexing channels. Using cascaded quasi-phase matched sum/difference frequency generation, the signal photon of a photon pair from spontaneous down-conversion is precisely shifted to identically match its counterpart, i.e. idler photon, in frequency to manifest a clear non-classical dip in the Hong-Ou-Mandel interference. Moreover, quantum entanglement between the photon pair is maintained after the frequency conversion. Our researches have realized three significant quantum interfaces via single-photon frequency conversion, which hold great promise for the development of quantum communications and networks.
Signal photons emitted by quantum nodes typically fall outside the low-loss telecom window of optical fibers, leading to severe transmission losses. Quantum frequency conversion (QFC) offers an effective optical interface that bridges quantum nodes with telecom-band channels, enabling long-distance quantum communication. In this work, we demonstrate a compact, fiber-integrated QFC system with low noise and a high signal-to-noise ratio (SNR). Using a periodically poled lithium niobate (PPLN) waveguide, input photons at 637.2 nm are down-converted to telecom photons at 1588.3 nm. Our system achieves a total conversion efficiency of approximately 9%, with pump-induced noise suppressed to 154 Hz. For input photon rates of 32.7, 118.0, and 327.7 kHz, the corresponding SNRs are 12.3, 43.9, and 117.8, respectively. We further develop a theoretical model to simulate the entanglement fidelity between nitrogen-vacancy (NV) center spins and the frequency-converted telecom photons. At the emission rate of an NV center, our QFC system maintains an expected fidelity exceeding 52% over a transmission distance of 100 km. These findings highlight the potential of our QFC system for scalable, long-distance quantum networking.