Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2206.09489 · Applied Physics Letters

Aluminum air bridges for superconducting quantum devices realized using a single-step electron-beam lithography process

N. Janzen, Michal Kononenko, S. Ren, Adrian Lupaşcu

Published Aug 29, 2022• 14 citations
arXivHTMLPDF

Abstract

In superconducting quantum devices, air bridges enable increased circuit complexity and density, and mitigate the risk of microwave loss arising from mode mixing. We implement aluminum air bridges using a simple process based on single-step electron-beam gradient exposure. The resulting bridges have sizes ranging from 20 µm to 100 µm, with a yield exceeding 99% for lengths up to 36 µm. When used to connect ground planes in coplanar waveguide resonators, the induced loss contributed to the system is negligible, corresponding to a loss per bridge less than 1.0×10−8. The bridge process is compatible with Josephson junctions and allows for the simultaneous creation of low loss bandages between superconducting layers.

DOI
10.1063/5.0103165

Related papers

Fabrication of large dimension aluminum air-bridges for superconducting quantum circuits

Mohammad Abuwasib, Philip Krantz, Per Delsing

Proper grounding between different ground planes in coplanar superconducting qubit circuits is important to avoid spurious resonances which increase decoherence. Here, the authors present a possible solution to suppress such undesired modes using superconducting aluminum air-bridges which have been fabricated on top of aluminum coplanar waveguide transmission lines. 3D electromagnetic simulations were done to guide the design of the air-bridges such that the input reflection (S11) of the bridges was kept at a minimum level. A fabrication method based on optical lithography techniques was developed and it resulted in air-bridges with a height of approximately 10 μm and lengths of up to 500 μm. The method can be generalized to arbitrary length air-bridge with heights even exceeding 15 μm.

Journal of Vacuum Science & Technology B Nanotechnology and Microelectronics Materials Processing Measurement and Phenomena•Apr 4, 2013•31 citations

Aluminum Air Bridges for Integrated Superconducting Quantum Circuits

L. Kaczmarek, M. Schmelz, E. Mutsenik +4 more

Superconducting circuits are one of the most promising realizations for quantum technologies especially for quantum computing. Corresponding research must consider both: the quantum bit (so-called qubit) itself, which is often implemented as a transmon-type qubit for large scale applications, and the qubit's on-chip environment. Therein, coplanar waveguide resonators and coplanar transmission lines are mostly used for addressing and reading out the transmons. The coplanar resonators need to have high intrinsic quality factors which significantly depend on the material and the fabrication process. Consequently, a profound knowledge of the fabrication process is mandatory. For an increasing number of qubits on a chip and, thus, more complex circuit designs, beyond 2-D integration technologies are required to suppress unwanted slotline modes due to anharmonicities and discontinuities within the circuits ground planes. Superconducting low-inductance air bridges can ensure this feature by equalizing the ground planes’ potential. The aim of this work is to describe our recent progress in wafer-scale fabrication of beyond 2-D superconducting quantum circuits. We show a combined study of resonator circuits and aluminum air bridges. We discuss our optimized fabrication process for resonator circuits with intrinsic quality factors up to approx.Qi= 2,000,000 at high photon numbers as well as the implementation of air bridges into resonator circuits. Finally, we demonstrate the successful implementation of air bridges in context of open quantum systems.

IEEE Transactions on Applied Superconductivity•Sep 2, 2026•0 citations

Contacting Josephson Junctions via Airbridges in Superconducting Circuits

Prakiran Baidya, Momčilo Milosavljević, Murali Krishna Kurmapu +6 more

Superconducting circuit devices require electrical interconnects between different circuit elements on the chip, for which conventional device architectures use a combination of two structural elements: \textit{airbridges} to connect non-adjacent elements in the base layer, and \textit{bandages} to connect the electrodes forming the Josephson junctions to the base layer. Bandages introduce unwanted parasitic material interfaces and increase the manufacturing complexity. Here, we overcome the limitations imposed by \emph{bandages} by establishing \textit{all} electrical interconnects with airbridges of varying size fabricated in a single step. The airbridges show a high yield and mechanical stability over a wide range of sizes from $0.5\,μ\mathrm{m}$ to $4\,μ\mathrm{m}$ in width and from $5\,μ\mathrm{m}$ to $40\,μ\mathrm{m}$ in length, and show low loss when integrated in coplanar waveguide resonators and transmon qubits. Measured relaxation times up to more than $250\,μ\mathrm{s}$ in standard transmon geometries show that the process achieves high coherence while substantially easing and accelerating device fabrication.

quant-pharXiv:2606.06951•Jun 8, 2026•0 citations

Fabrication of metal air bridges for superconducting circuits using two-photon lithography

Yi-Hsiang Huang, H. Wang, Zhuo Shen +3 more

Extraneous high frequency chip modes parasitic to superconducting quantum circuits can result in decoherence when these modes are excited. To suppress these modes, superconducting air bridges (AB) are commonly used to electrically connect ground planes together when interrupted by transmission lines. Here, we demonstrate the use of two-photon photolithography to build a supporting 3D resist structure in conjunction with a liftoff process to create AB. The resulting aluminum AB have a superconducting transition temperature of Tc=1.08 K and exhibit good mechanical strength up to lengths of 100 μm. A measurable amount of microwave loss is observed when 35 AB were placed over a high-Q Ta quarter-wave coplanar waveguide resonator.

arXiv:2503.10909•Applied Physics Letters•Jul 28, 2025•2 citations

Niobium air bridges as low-loss components for superconducting quantum hardware

N. Bruckmoser, L. Koch, I. Tsitsilin +12 more

Scaling up superconducting quantum processors necessitates the use of a high routing density for readout and control lines, relying on low-loss interconnects to maintain design flexibility and device performance. We propose and demonstrate a universal subtractive fabrication process for air bridges based on an aluminum hard mask and niobium as the superconducting film. Using this technology, we fabricate superconducting coplanar waveguide resonators incorporating several niobium air bridges in and across their center conductors. Through rigorous cleaning methods, we achieve mean internal quality factors in the single-photon limit exceeding Q int = 8.2 × 10 6 . Notably, the loss per air bridge remains below the detection threshold of the resonators. Due to the larger superconducting energy gap of niobium, compared with conventional aluminum air bridges, our approach enables stable performance at elevated temperatures and magnetic fields, which we experimentally confirm in temperatures up to 3.9 K and in a magnetic field of up to 1.60 T. Additionally, we utilize air bridges to realize low-loss vacuum-gap capacitors and demonstrate their successful integration in transmon qubits by achieving median qubit lifetimes of T 1 = 51.6 μ s .

arXiv:2503.12076•Physical Review Applied•Dec 9, 2025•11 citations

Low loss superconducting resonators enabled by aluminum microstructural engineering and dielectric trimming

Mahmoud Almansouri, Umar T. F. Alhuwaymel, Ibraheem AlYousef +5 more

Material losses in superconducting circuits fundamentally limit qubit coherence times and resonator quality factors. Most research efforts focus on mitigating losses at circuit interfaces, including metal--substrate, substrate--air, and metal--air interfaces. However, the correlation between TLS and non-TLS losses with the intrinsic properties of the superconducting metal and the dielectric edge smoothness is not well studied. In this work, we link the aluminum film grain size to non-TLS losses and the dielectric trimming profile and roughness to TLS loss; both loss mechanisms are subsequently mitigated. To reduce metal-related losses, we engineer the aluminum microstructure by heating during deposition, increasing grain size and reducing grain boundary density. Beyond mitigating metal losses, we introduce a two-step etching technique, Tropic etching, to suppress dielectric TLS loss by producing an ultra-smooth silicon surface with minimal defects and redeposition. These results lay out the fabrication pathway for aluminum resonators with lower loss, demonstrating two-orders-of-magnitude improvement in quality factor from $6\times10^{4}$ to $2.3\times10^{6}$. Since aluminum is the basis for most high-coherence Josephson junctions and dielectric edges are inherent to all common device geometries, the improvements in aluminum microstructure and edge profiling, presented here, can enhance the performance of superconducting quantum devices.

quant-pharXiv:2607.22265•Jul 27, 2026•1 citation
In superconducting quantum devices, air bridges enable increased circuit complexity and density, and mitigate the risk of microwave loss arising from mode mixing. We implement aluminum air bridges using a simple process based on single-step electron-beam gradient exposure. The resulting bridges have sizes ranging from 20 µm to 100 µm, with a yield exceeding 99% for lengths up to 36 µm. When used to connect ground planes in coplanar waveguide resonators, the induced loss contributed to the system is negligible, corresponding to a loss per bridge less than 1.0×10−8. The bridge process is compatible with Josephson junctions and allows for the simultaneous creation of low loss bandages between superconducting layers.
Proper grounding between different ground planes in coplanar superconducting qubit circuits is important to avoid spurious resonances which increase decoherence. Here, the authors present a possible solution to suppress such undesired modes using superconducting aluminum air-bridges which have been fabricated on top of aluminum coplanar waveguide transmission lines. 3D electromagnetic simulations were done to guide the design of the air-bridges such that the input reflection (S11) of the bridges was kept at a minimum level. A fabrication method based on optical lithography techniques was developed and it resulted in air-bridges with a height of approximately 10 μm and lengths of up to 500 μm. The method can be generalized to arbitrary length air-bridge with heights even exceeding 15 μm.
Superconducting circuits are one of the most promising realizations for quantum technologies especially for quantum computing. Corresponding research must consider both: the quantum bit (so-called qubit) itself, which is often implemented as a transmon-type qubit for large scale applications, and the qubit's on-chip environment. Therein, coplanar waveguide resonators and coplanar transmission lines are mostly used for addressing and reading out the transmons. The coplanar resonators need to have high intrinsic quality factors which significantly depend on the material and the fabrication process. Consequently, a profound knowledge of the fabrication process is mandatory. For an increasing number of qubits on a chip and, thus, more complex circuit designs, beyond 2-D integration technologies are required to suppress unwanted slotline modes due to anharmonicities and discontinuities within the circuits ground planes. Superconducting low-inductance air bridges can ensure this feature by equalizing the ground planes’ potential. The aim of this work is to describe our recent progress in wafer-scale fabrication of beyond 2-D superconducting quantum circuits. We show a combined study of resonator circuits and aluminum air bridges. We discuss our optimized fabrication process for resonator circuits with intrinsic quality factors up to approx.Qi= 2,000,000 at high photon numbers as well as the implementation of air bridges into resonator circuits. Finally, we demonstrate the successful implementation of air bridges in context of open quantum systems.
Superconducting circuit devices require electrical interconnects between different circuit elements on the chip, for which conventional device architectures use a combination of two structural elements: \textit{airbridges} to connect non-adjacent elements in the base layer, and \textit{bandages} to connect the electrodes forming the Josephson junctions to the base layer. Bandages introduce unwanted parasitic material interfaces and increase the manufacturing complexity. Here, we overcome the limitations imposed by \emph{bandages} by establishing \textit{all} electrical interconnects with airbridges of varying size fabricated in a single step. The airbridges show a high yield and mechanical stability over a wide range of sizes from 0.5 μm0.5\,μ\mathrm{m}0.5μm to 4 μm4\,μ\mathrm{m}4μm in width and from 5 μm5\,μ\mathrm{m}5μm to 40 μm40\,μ\mathrm{m}40μm in length, and show low loss when integrated in coplanar waveguide resonators and transmon qubits. Measured relaxation times up to more than 250 μs250\,μ\mathrm{s}250μs in standard transmon geometries show that the process achieves high coherence while substantially easing and accelerating device fabrication.
Extraneous high frequency chip modes parasitic to superconducting quantum circuits can result in decoherence when these modes are excited. To suppress these modes, superconducting air bridges (AB) are commonly used to electrically connect ground planes together when interrupted by transmission lines. Here, we demonstrate the use of two-photon photolithography to build a supporting 3D resist structure in conjunction with a liftoff process to create AB. The resulting aluminum AB have a superconducting transition temperature of Tc=1.08 K and exhibit good mechanical strength up to lengths of 100 μm. A measurable amount of microwave loss is observed when 35 AB were placed over a high-Q Ta quarter-wave coplanar waveguide resonator.
Scaling up superconducting quantum processors necessitates the use of a high routing density for readout and control lines, relying on low-loss interconnects to maintain design flexibility and device performance. We propose and demonstrate a universal subtractive fabrication process for air bridges based on an aluminum hard mask and niobium as the superconducting film. Using this technology, we fabricate superconducting coplanar waveguide resonators incorporating several niobium air bridges in and across their center conductors. Through rigorous cleaning methods, we achieve mean internal quality factors in the single-photon limit exceeding Q int = 8.2 × 10 6 . Notably, the loss per air bridge remains below the detection threshold of the resonators. Due to the larger superconducting energy gap of niobium, compared with conventional aluminum air bridges, our approach enables stable performance at elevated temperatures and magnetic fields, which we experimentally confirm in temperatures up to 3.9 K and in a magnetic field of up to 1.60 T. Additionally, we utilize air bridges to realize low-loss vacuum-gap capacitors and demonstrate their successful integration in transmon qubits by achieving median qubit lifetimes of T 1 = 51.6 μ s .
Material losses in superconducting circuits fundamentally limit qubit coherence times and resonator quality factors. Most research efforts focus on mitigating losses at circuit interfaces, including metal--substrate, substrate--air, and metal--air interfaces. However, the correlation between TLS and non-TLS losses with the intrinsic properties of the superconducting metal and the dielectric edge smoothness is not well studied. In this work, we link the aluminum film grain size to non-TLS losses and the dielectric trimming profile and roughness to TLS loss; both loss mechanisms are subsequently mitigated. To reduce metal-related losses, we engineer the aluminum microstructure by heating during deposition, increasing grain size and reducing grain boundary density. Beyond mitigating metal losses, we introduce a two-step etching technique, Tropic etching, to suppress dielectric TLS loss by producing an ultra-smooth silicon surface with minimal defects and redeposition. These results lay out the fabrication pathway for aluminum resonators with lower loss, demonstrating two-orders-of-magnitude improvement in quality factor from 6×1046\times10^{4}6×104 to 2.3×1062.3\times10^{6}2.3×106. Since aluminum is the basis for most high-coherence Josephson junctions and dielectric edges are inherent to all common device geometries, the improvements in aluminum microstructure and edge profiling, presented here, can enhance the performance of superconducting quantum devices.