Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2107.06491 · Physical Review A

Simulation of the five-qubit quantum error correction code on superconducting qubits

Ilya A. Simakov, Ilya S. Besedin, Alexey Vladimirovich Ustinov

Published Mar 3, 2022• 8 citations
arXivHTMLPDF

Abstract

Experimental realization of stabilizer-based quantum error correction (QEC) codes that would yield superior logical qubit performance is one of the formidable task for state-of-the-art quantum processors. A major obstacle toward realizing this goal is the large footprint of QEC codes, even those with a small distance. We propose a circuit based on the minimal distance-3 QEC code, which requires only five data qubits and five ancilla qubits, connected in a ring with iswap gates implemented between neighboring qubits. Using a density-matrix simulation, we show that, thanks to its smaller footprint, the proposed code has a lower logical error rate than surface-17 for similar physical error rates. We also estimate the performance of a neural-network-based error decoder, which can be trained to accommodate the error statistics of a specific quantum processor by training on experimental data.

DOI
10.1103/physreva.105.032409

Related papers

Neural-Network Decoders for Quantum Error Correction Using Surface Codes: A Space Exploration of the Hardware Cost-Performance Tradeoffs

Ramon W. J. Overwater, Masoud Babaie, Fabio Sebastiano

Quantum Error Correction (QEC) is required in quantum computers to mitigate the effect of errors on physical qubits. When adopting a QEC scheme based on surface codes, error decoding is the most computationally expensive task in the classical electronic back-end. Decoders employing neural networks (NN) are well-suited for this task but their hardware implementation has not been presented yet. This work presents a space exploration of fully-connected feed-forward NN decoders for small distance surface codes. The goal is to optimize the neural network for high decoding performance, while keeping a minimalistic hardware implementation. This is needed to meet the tight delay constraints of real-time surface code decoding. We demonstrate that hardware based NN-decoders can achieve high decoding performance comparable to other state-of-the-art decoding algorithms whilst being well below the tight delay requirements (440 ns) of current solid-state qubit technologies for both ASIC designs (<30 ns) and FPGA implementations (<90 ns). These results indicate that NN-decoders are viable candidates for further exploration of an integrated hardware implementation in future large-scale quantum computers.

arXiv:2202.05741•IEEE Transactions on Quantum Engineering•Jan 1, 2022•87 citations

Low-overhead quantum error-correction codes with a cyclic topology

Ilya A. Simakov, Ilya S. Besedin

Quantum error correction is an important ingredient for scalable quantum computing. Stabilizer codes are one of the most promising and straightforward ways to correct quantum errors, are convenient for logical operations, and improve performance with increasing the number of qubits involved. Here, we propose a resource-efficient scaling of a five-qubit perfect code with increasing-weight cyclic stabilizers for small distances on the ring architecture, which takes into account the topological features of the superconducting platform. We show an approach to construct the quantum circuit of a correction code with ancillas entangled with non-neighboring data qubits. Furthermore, we introduce a neural network-based decoding algorithm supported by an improved lookup table decoder and provide a numerical simulation of the proposed code, which demonstrates the exponential suppression of the logical error rate.

arXiv:2211.03094•Physical Review A•Jan 30, 2025•8 citations

Surface-code Superconducting Quantum Processors: From Calibration To Logical Performance

Hany A. Ali

Current quantum processors are fragile, noisy and fairly limited in both quantity and quality with tens of qubits and physical error rates of around 10^-3. To realize practical quantum applications, however, error rates need to be below 10^-15 across millions of qubits. To bridge this gap and fully harness the potential of quantum computers, quantum error correction (QEC) is essential. QEC codes are designed to protect quantum information by redundantly encoding it onto multiple physical qubits. This encoding allows for the detection and correction of local errors affecting individual qubits, e.g., through stabilizer measurements. Importantly, if the physical error rates are below a specific threshold, QEC codes can exponentially suppress logical error rates by increasing the number of physical qubits involved. This is essential for achieving fault-tolerant computations, which are key to unlocking the full potential of quantum computers. The work presented in this thesis focuses on the implementation and optimization of small-scale QEC experiments using the surface code and flux-tunable superconducting qubits (Transmons). It addresses several key challenges: enhancing two-qubit gate fidelity in Surface-4 (Chapter 2), implementing an error-detection code with Surface-7 (Chapter 3), automating the calibration and benchmarking of the building blocks in Surface-17 (Chapter 4), reducing leakage into higher excited states with leakage reduction units (Chapter 5), assessing and enhancing the performance of logical qubits (Chapters 7 and 8).

arXiv:2504.17082•Apr 23, 2025•1 citation

Density matrix simulation of quantum error correction codes for near-term quantum devices

Chungheon Baek, Tomohiro Ostuka, Seigo Tarucha +1 more

Abstract Fault-tolerant quantum computing requires many qubits with long lifetimes and accurate quantum gate operations. However, external noise limits the computing time and hampers accurate quantum gate operations. Quantum error correction (QEC) codes may extend such limits, but imperfect gate operations during QEC cause errors, which could cancel out QEC. We used density matrix simulations to examine the performance of QEC codes with five qubits. In current quantum devices, less than ten qubits are needed to conduct sufficient gate operations within their lifetime so that it is feasible to implement QEC codes. We analyzed the maximum tolerable error rate and error correction effect of individual QEC codes according to the qubit arrangement and gate accuracy. Assuming a 0.1% gate error probability, a logical ∣ 1 〉 state encoded by a five-qubit QEC code is expected to have a 0.25 higher fidelity than its physical counterpart.

arXiv:1810.01029•Quantum Science and Technology•Nov 18, 2019•12 citations

Neural Network based Decoders for the Surface Code

Savvas Varsamopoulos

Quantum error correction (QEC) is key to have reliable quantum computation and storage, due to the fragility of qubits in current quantum technology and the imperfect application of quantum operations. In order to have efficient quantum computation and storage, active QEC is required. QEC consists of an encoding and a decoding process. The way that encoding protects quantum information is through grouping many unreliable physical qubits into one more reliable logical qubit. Then, computation occurs based on the logical qubits, however, errors still occur on the physical qubits. Decoding is the process of identifying the location and type of errors occurring on the physical qubits. The decoder proposes corrections against the errors that have been identified. In this thesis, we are exploring novel ways to design decoders for QEC codes, focusing on the surface code. We began our investigation by implementing a rule-based decoder for the smallest surface code, which consists of 17 qubits. We incorporated this decoder to a platform that we created, called Quantum Platform Development Framework (QPDO), in order to study the working principles of a Pauli frame and to quantify its potential effect on the decoding performance. The Pauli frame unit keeps track of errors on physical qubits without the need to apply corrections constantly. We quantified through simulation the benefits in terms of the decoding performance and the execution schedule of QEC, minimizing the idle time. Minimizing the execution time is critical, due to the limited time budget of quantum error correction, thus requiring a high speed decoder capable of still reaching high decoding performance. We show that when the decoding time is equal to the time required to run a surface code cycle, the decoder reaches its maximum performance. However, such a rule-based decoder cannot easily scale to larger quantum systems, therefore other decoding approaches should be considered. Most of the classical decoders that have been developed so far, do not have a good balance between short execution time and high decoding performance. Therefore, we proposed decoders that incorporate neural networks to keep the execution time small, while keeping the decoding performance high. We designed a two-module decoder, which included a classical module and a neural network. We named this configuration neural network based decoder (NNbD). We compare different designs of NNbDs with classical decoders and prove that NNbDs can reach similar or better decoding performance compared to classical decoders while having constant execution time. Furthermore, we quantified the execution time of a NNbD and argued about the speed that can be achieved in a hardware chip like a Field Programmable Gate Array (FPGA) or an Application-Specific Integrated Circuit (ASIC). Both the classical module and the neural network are highly parallelizable and fast modules by construction, leading to constant execution time for a given code distance. We proved that neural network based decoders can adapt to any noise model, since the neural network functionality is based on creating a map between the input and output data, requiring no knowledge about the underlying error model. Following that, a comparison between different NNbD design approaches was performed. We show that it is advantageous to start with a classical decoding module and improve on its decoding performance with a neural network rather than having a neural network perform the decoding on its own. Also, in the latter case, the execution time of such a decoder is non-constant and on average larger than the decoder containing a classical module and a neural network. Moreover, we show that for the design containing a classical module and a neural network, the execution time is increasing linearly as the code distance increased, which was mainly attributed to the increase of the size of the neural network. However, there is a fundamental difference between NNbDs and classical decoders in that NNbDs require sampling and training based on data obtained from the problem, unlike classical decoders. As the code distance increases, the amount of data required to be gathered and trained are exponentially increasing, imposing a limit to the size of the quantum system that can be efficiently decoded. We proposed as a solution to have a distributed decoding approach that divides the code into small regions and then decodes each region locally. We show that using such a distributed decoding approach for small code distances does not lead to significant loss in decoding performance, while simultaneously providing a way to decode large code distances. Thus, we were able to create a decoder that can achieve high decoding performance with constant execution time. However, there are still some issues to keep in mind with such kind of decoders. The main challenge of NNbDs is that they are a dedicated decoder for a given problem. Every time that some aspect of the problem changes (quantum error correcting code, code distance, error model), sampling, training and evaluating the decoder needs to be repeated. Moreover, there is a large number of neural network parameters that need to be specifically tuned when the problem changes. A careful study of the design choices is required to maximize the performance of the decoder. We envision that when sampling and training are performed in hardware, the time required for these processes will be decreased compared to the time required in software. Finally, if the hardware resources allow us to include multiple neural networks, then this can potentially increase the decoding performance. As we presented, dividing the task of decoding to smaller tasks that are distributed to many neural networks can be beneficial.

•May 1, 2019•2 citations

Real-time Surface-Code Error Correction Using an FPGA-based Neural-Network Decoder

Xiaohan Yang, Xuandong Sun, Zhiyi Wu +9 more

Quantum error correction (QEC) is essential for achieving low error rates required for fault-tolerant quantum computation. In stabilizer-based codes such as the surface code, errors are inferred from repeated syndrome measurements and corrected by a classical decoder. To prevent error accumulation, decoding must be performed with both high throughput and low latency to keep pace with the QEC cycle and enable real-time feedback for universal logical operations. Here we report a hardware-integrated control architecture featuring an FPGA-based neural-network (NN) decoder and experimentally demonstrate real-time surface-code (distance-3) QEC on a superconducting quantum processor. The system achieves a deterministic closed-loop latency of 550 ns, including 124 ns for NN decoding, enabling feedback corrections within a 1.25 us QEC cycle. We show that real-time decoding and feedback correction achieve logical performance comparable to offline decoding while maintaining robustness against varying error conditions. We further demonstrate mid-circuit feedback correction in non-Clifford logical circuits, where Pauli-frame updating alone becomes insufficient. Our results establish a low-latency hardware architecture for embedded QEC control and provide a pathway towards scalable fault-tolerant quantum computing systems.

quant-pharXiv:2605.04892•May 7, 2026•8 citations
Experimental realization of stabilizer-based quantum error correction (QEC) codes that would yield superior logical qubit performance is one of the formidable task for state-of-the-art quantum processors. A major obstacle toward realizing this goal is the large footprint of QEC codes, even those with a small distance. We propose a circuit based on the minimal distance-3 QEC code, which requires only five data qubits and five ancilla qubits, connected in a ring with iswap gates implemented between neighboring qubits. Using a density-matrix simulation, we show that, thanks to its smaller footprint, the proposed code has a lower logical error rate than surface-17 for similar physical error rates. We also estimate the performance of a neural-network-based error decoder, which can be trained to accommodate the error statistics of a specific quantum processor by training on experimental data.
Quantum Error Correction (QEC) is required in quantum computers to mitigate the effect of errors on physical qubits. When adopting a QEC scheme based on surface codes, error decoding is the most computationally expensive task in the classical electronic back-end. Decoders employing neural networks (NN) are well-suited for this task but their hardware implementation has not been presented yet. This work presents a space exploration of fully-connected feed-forward NN decoders for small distance surface codes. The goal is to optimize the neural network for high decoding performance, while keeping a minimalistic hardware implementation. This is needed to meet the tight delay constraints of real-time surface code decoding. We demonstrate that hardware based NN-decoders can achieve high decoding performance comparable to other state-of-the-art decoding algorithms whilst being well below the tight delay requirements (440 ns) of current solid-state qubit technologies for both ASIC designs (<30 ns) and FPGA implementations (<90 ns). These results indicate that NN-decoders are viable candidates for further exploration of an integrated hardware implementation in future large-scale quantum computers.
Quantum error correction is an important ingredient for scalable quantum computing. Stabilizer codes are one of the most promising and straightforward ways to correct quantum errors, are convenient for logical operations, and improve performance with increasing the number of qubits involved. Here, we propose a resource-efficient scaling of a five-qubit perfect code with increasing-weight cyclic stabilizers for small distances on the ring architecture, which takes into account the topological features of the superconducting platform. We show an approach to construct the quantum circuit of a correction code with ancillas entangled with non-neighboring data qubits. Furthermore, we introduce a neural network-based decoding algorithm supported by an improved lookup table decoder and provide a numerical simulation of the proposed code, which demonstrates the exponential suppression of the logical error rate.
Current quantum processors are fragile, noisy and fairly limited in both quantity and quality with tens of qubits and physical error rates of around 10^-3. To realize practical quantum applications, however, error rates need to be below 10^-15 across millions of qubits. To bridge this gap and fully harness the potential of quantum computers, quantum error correction (QEC) is essential. QEC codes are designed to protect quantum information by redundantly encoding it onto multiple physical qubits. This encoding allows for the detection and correction of local errors affecting individual qubits, e.g., through stabilizer measurements. Importantly, if the physical error rates are below a specific threshold, QEC codes can exponentially suppress logical error rates by increasing the number of physical qubits involved. This is essential for achieving fault-tolerant computations, which are key to unlocking the full potential of quantum computers. The work presented in this thesis focuses on the implementation and optimization of small-scale QEC experiments using the surface code and flux-tunable superconducting qubits (Transmons). It addresses several key challenges: enhancing two-qubit gate fidelity in Surface-4 (Chapter 2), implementing an error-detection code with Surface-7 (Chapter 3), automating the calibration and benchmarking of the building blocks in Surface-17 (Chapter 4), reducing leakage into higher excited states with leakage reduction units (Chapter 5), assessing and enhancing the performance of logical qubits (Chapters 7 and 8).
Abstract Fault-tolerant quantum computing requires many qubits with long lifetimes and accurate quantum gate operations. However, external noise limits the computing time and hampers accurate quantum gate operations. Quantum error correction (QEC) codes may extend such limits, but imperfect gate operations during QEC cause errors, which could cancel out QEC. We used density matrix simulations to examine the performance of QEC codes with five qubits. In current quantum devices, less than ten qubits are needed to conduct sufficient gate operations within their lifetime so that it is feasible to implement QEC codes. We analyzed the maximum tolerable error rate and error correction effect of individual QEC codes according to the qubit arrangement and gate accuracy. Assuming a 0.1% gate error probability, a logical ∣ 1 〉 state encoded by a five-qubit QEC code is expected to have a 0.25 higher fidelity than its physical counterpart.
Quantum error correction (QEC) is key to have reliable quantum computation and storage, due to the fragility of qubits in current quantum technology and the imperfect application of quantum operations. In order to have efficient quantum computation and storage, active QEC is required. QEC consists of an encoding and a decoding process. The way that encoding protects quantum information is through grouping many unreliable physical qubits into one more reliable logical qubit. Then, computation occurs based on the logical qubits, however, errors still occur on the physical qubits. Decoding is the process of identifying the location and type of errors occurring on the physical qubits. The decoder proposes corrections against the errors that have been identified. In this thesis, we are exploring novel ways to design decoders for QEC codes, focusing on the surface code. We began our investigation by implementing a rule-based decoder for the smallest surface code, which consists of 17 qubits. We incorporated this decoder to a platform that we created, called Quantum Platform Development Framework (QPDO), in order to study the working principles of a Pauli frame and to quantify its potential effect on the decoding performance. The Pauli frame unit keeps track of errors on physical qubits without the need to apply corrections constantly. We quantified through simulation the benefits in terms of the decoding performance and the execution schedule of QEC, minimizing the idle time. Minimizing the execution time is critical, due to the limited time budget of quantum error correction, thus requiring a high speed decoder capable of still reaching high decoding performance. We show that when the decoding time is equal to the time required to run a surface code cycle, the decoder reaches its maximum performance. However, such a rule-based decoder cannot easily scale to larger quantum systems, therefore other decoding approaches should be considered. Most of the classical decoders that have been developed so far, do not have a good balance between short execution time and high decoding performance. Therefore, we proposed decoders that incorporate neural networks to keep the execution time small, while keeping the decoding performance high. We designed a two-module decoder, which included a classical module and a neural network. We named this configuration neural network based decoder (NNbD). We compare different designs of NNbDs with classical decoders and prove that NNbDs can reach similar or better decoding performance compared to classical decoders while having constant execution time. Furthermore, we quantified the execution time of a NNbD and argued about the speed that can be achieved in a hardware chip like a Field Programmable Gate Array (FPGA) or an Application-Specific Integrated Circuit (ASIC). Both the classical module and the neural network are highly parallelizable and fast modules by construction, leading to constant execution time for a given code distance. We proved that neural network based decoders can adapt to any noise model, since the neural network functionality is based on creating a map between the input and output data, requiring no knowledge about the underlying error model. Following that, a comparison between different NNbD design approaches was performed. We show that it is advantageous to start with a classical decoding module and improve on its decoding performance with a neural network rather than having a neural network perform the decoding on its own. Also, in the latter case, the execution time of such a decoder is non-constant and on average larger than the decoder containing a classical module and a neural network. Moreover, we show that for the design containing a classical module and a neural network, the execution time is increasing linearly as the code distance increased, which was mainly attributed to the increase of the size of the neural network. However, there is a fundamental difference between NNbDs and classical decoders in that NNbDs require sampling and training based on data obtained from the problem, unlike classical decoders. As the code distance increases, the amount of data required to be gathered and trained are exponentially increasing, imposing a limit to the size of the quantum system that can be efficiently decoded. We proposed as a solution to have a distributed decoding approach that divides the code into small regions and then decodes each region locally. We show that using such a distributed decoding approach for small code distances does not lead to significant loss in decoding performance, while simultaneously providing a way to decode large code distances. Thus, we were able to create a decoder that can achieve high decoding performance with constant execution time. However, there are still some issues to keep in mind with such kind of decoders. The main challenge of NNbDs is that they are a dedicated decoder for a given problem. Every time that some aspect of the problem changes (quantum error correcting code, code distance, error model), sampling, training and evaluating the decoder needs to be repeated. Moreover, there is a large number of neural network parameters that need to be specifically tuned when the problem changes. A careful study of the design choices is required to maximize the performance of the decoder. We envision that when sampling and training are performed in hardware, the time required for these processes will be decreased compared to the time required in software. Finally, if the hardware resources allow us to include multiple neural networks, then this can potentially increase the decoding performance. As we presented, dividing the task of decoding to smaller tasks that are distributed to many neural networks can be beneficial.
Quantum error correction (QEC) is essential for achieving low error rates required for fault-tolerant quantum computation. In stabilizer-based codes such as the surface code, errors are inferred from repeated syndrome measurements and corrected by a classical decoder. To prevent error accumulation, decoding must be performed with both high throughput and low latency to keep pace with the QEC cycle and enable real-time feedback for universal logical operations. Here we report a hardware-integrated control architecture featuring an FPGA-based neural-network (NN) decoder and experimentally demonstrate real-time surface-code (distance-3) QEC on a superconducting quantum processor. The system achieves a deterministic closed-loop latency of 550 ns, including 124 ns for NN decoding, enabling feedback corrections within a 1.25 us QEC cycle. We show that real-time decoding and feedback correction achieve logical performance comparable to offline decoding while maintaining robustness against varying error conditions. We further demonstrate mid-circuit feedback correction in non-Clifford logical circuits, where Pauli-frame updating alone becomes insufficient. Our results establish a low-latency hardware architecture for embedded QEC control and provide a pathway towards scalable fault-tolerant quantum computing systems.