Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2102.00251 · Optics Express

High-flux, adjustable, compact cold-atom source

Sean Ravenhall, Benjamin Yuen, Christopher J. Foot

Published May 17, 2021• 22 citations
arXivHTMLPDF

Abstract

Magneto-optical traps (MOTs) are widely used for laser cooling of atoms. We have developed a high-flux compact cold-atom source based on a pyramid MOT with a unique adjustable aperture that is highly suitable for portable quantum technology devices, including space-based experiments. The adjustability enabled an investigation into the previously unexplored impact of aperture size on the atomic flux, and optimisation of the aperture size allowed us to demonstrate a higher flux than any reported cold-atom sources that use a pyramid, LVIS, 3D-MOT or grating MOT. We achieved 2.1(1) × 1010 atoms/s of 87Rb with a mean velocity of 32(1) m/s, FWHM of 27.6(9) m/s and divergence of 59(4) mrad. Halving the total optical power to 195 mW caused only a 20% reduction of the flux, and a 30% decrease in mean velocity. Methods to further decrease the velocity as required have been identified. The low power consumption and small size make this design suitable for a wide range of cold-atom technologies.

DOI
10.1364/oe.423662

Related papers

A compact, high-flux source of cold atoms

Sean Ravenhall

The ongoing drive to transfer quantum technologies from research laboratories to practical, portable devices requires the development of multiple key enabling technologies. The field of cold atoms, which includes high-precision metrology and quantum simulation, has various real-world applications including time-keeping and navigation. A crucial component in these systems is a cold-atom source that generates a flux of low-velocity atoms suitable for subsequent capture. A large flux enables fast repetition rates, high duty cycles, long measurement times, and resistance to long-term performance degradation with a good signal-to-noise ratio, all of which are essential to produce cold-atom devices and technologies that are capable of out-performing the classical alternatives. This thesis presents the design, fabrication and characterisation of a novel cold-atom source using a compact pyramidal magneto-optical trap (MOT) with a unique adjustable-aperture mechanism. This allowed an investigation of the dependence of the flux characteristics on the aperture size, a parameter space that has not previously been explored. The measurements showed a strong dependence of the flux on the aperture size, with a negligible flux below 0.4mm, then an approximately linear increase up to 1.0mm, at which point the relationship showed possible signs of saturation. Using 87Rb, a flux of 1.18×1010 atoms/s was produced using a 1.27mm aperture, for which the mean velocity of the atoms was 21.6(3) m/s with a FWHM of 11.2(2) m/s, and the FWHM divergence of the beam was 86(2) mrad. This is the highest recorded flux from a pyramid or 2D+-MOT source, and amongst the highest reported fluxes from any MOT sources, and avenues for improvement still remain. This work fulfils the aim of demonstrating a compact and robust cold-atom source generating a high flux of laser-cooled atoms for real-world quantum technology applications.

•Jan 1, 2018•1 citation

High-flux source of laser-cooled rubidium atoms for quantum technology applications

Christopher J. Foot, Sean Ravenhall

We have used a pyramid magneto-optical trap (MOT) to create a compact source of cold rubidium atoms. The four dielectric-coated metal mirrors in vacuum are arranged in the form of a pyramid that creates the light field for a MOT from a single ingoing laser beam. The atoms are pushed out through a hole (aperture) in the apex of the pyramid, in a direction determined by the laser light, to give a flux of Rb-87 atoms greater than 2 × 10^10 per second with a mean velocity of 33 m/s (FWHM of 28 m/s) and a divergence of 58 mrad. The pyramid MOT has a unique mechanism for adjusting aperture size and it is highly suitable for portable quantum technology devices.

•Oct 5, 2020•0 citations

Generation of an intense cold-atom beam from a pyramidal magneto-optical trap: experiment and simulation

James M. Kohel, Jaime Ramirez-Serrano, Robert J. Thompson +3 more

An intense cold-atom beam source based on a modified pyramidal magneto-optical trap has been developed and characterized. We have produced a slow beam of cold cesium atoms with a continuous flux of 2.2× 109 atoms/s at a mean velocity of 15 m/s and with a divergence of 15 mrad. The corresponding radiant intensity is 1.2×1013 atom s-1 sr-1. We have characterized the performance of our beam source over a range of operating conditions, and the measured values for atom flux, mean velocity, and divergence are in good agreement with results from detailed Monte Carlo numerical simulations.

Journal of the Optical Society of America B•Jun 1, 2003•49 citations

Multistage two-dimensional magneto-optical trap as a compact cold atom beam source

Jaime Ramirez-Serrano, Nan Yu, James M. Kohel +2 more

A compact cold atom beam source based on a multistage two-dimensional magneto-optical trap (MOT) has been demonstrated and characterized. The multiple-stage design greatly reduces the overall size of the source apparatus while providing a high flux of atoms. The cold atom beam was used to load a separate MOT in ultrahigh vacuum, and we obtained an actual trap loading rate of 1.5 x 109 atoms/s while using only 20 mW of total laser power for the source. The entire source apparatus, including optics, can fit into a 4 cm x 4 cm x 13 cm volume.

Optics Letters•Mar 15, 2006•21 citations

A new design of a compact strontium cold-atom source

Dongyang Xu

A high-flux compact source of strontium atoms has been designed and built. We have investigated the feasibility of direct trapping of cold atoms from the atomic flux out of a hot oven. Our design uses a two-dimensional magneto-optical trap (MOT) with an additional laser beam that exerts a radiation force that is not counterbalanced to eject atoms (so-called ‘push’ beam), which is known as a 2D+ MOT configuration. This approach has been previously used for sodium, and has been extended to strontium in this work. Laser cooling of strontium typically requires multiple stages: effusion of atoms from an oven to produce an atomic beam, transverse collimation, a Zeeman slower and deflection before finally collecting atoms in a 3D MOT. A 2D+ MOT combines the Zeeman slowing, transverse collimation, and deflection into a single compact stage to provide a high-flux source suitable for applications such as matter-wave interferometry, atomic clocks and experimental studies of degenerate quantum gases. This thesis reports experimental work that has been carried out to develop and test an oven and the associated laser cooling apparatus for producing a source of cold strontium atoms which is straightforward to manufacture. We test the oven up to a temperature of To = 642 °C and measure a peak intensity of 6.8 × 1016 s−1 sr−1 and a flux of 2.9 × 1016 s−1. We typically operate the oven at To = 502 °C, for which the peak intensity and flux are 2.2 × 1015 s−1 sr−1 and 7.5 × 1014 s−1. A multi-channel nozzle made of graphite gives an angular divergence of 0.17 rad (10°) for the atomic beam. Trapping atoms directly from the thermal atomic beam into the MOT gives a maximum loading rate of 7.1 × 1010 s−1, without any laser light to repump atoms into the cooling cycle. We demonstrated a novel frequency stabilising technique for the laser by developing Zeeman-tunable modulation transfer spectroscopy in strontium with an inaccuracy of ±3.5 MHz and a frequency tuning range of 160 MHz. The initial aim of this thesis was to make a compact, high-flux strontium source suitable for quantum technology applications. During the course of this research, we participated in the preparation of a proposal for the construction of a large-scale atom interferometer based on the clock transition in strontium (87Sr) for the exploration of dark matter and gravitational waves (a project known as the Atom Interferometer Observatory and Network, AION). This changed the design requirements towards producing a higher flux (in particular of the isotope 87Sr), with compactness of the source being less important in ∼10 m scale apparatus.

•Jan 1, 2020•0 citations

Generation of a cold atom beam from a pyramidal magneto-optical trap

J. L. Bliss, Kenneth G. Libbrecht, James M. Kohel +2 more

Summary form only given. A simple and robust design has been implemented based on the pyramidal trap geometry which allows use of single large diameter (/spl les/20 cm) laser beam to obtain large capture rates of atoms from the background vapor. The four 45/spl deg/ mirrors are truncated just before the apex of the pyramid, and the 1 cm/sup 2/ region at the center of the incident laser beam is retro-reflected by a /spl lambda//4 plate with a high-reflectance gold coating on the second surface. A small (1 mm diameter) hole in this retro-optic forms an extraction column for the atoms while maintaining a low conductance between the source region and an adjacent UHV chamber. The characterization of this large pyramidal low-velocity intense source (LVIS) is reported, including an investigation of scaling to very large (/spl ges/10 cm) high power (/spl sim/1 W) laser beams which should allow an improvement by a factor of 2-3 in beam flux over previous reports.

Quantum Electronics and Laser Science Conference•Jan 20, 2003•0 citations
Magneto-optical traps (MOTs) are widely used for laser cooling of atoms. We have developed a high-flux compact cold-atom source based on a pyramid MOT with a unique adjustable aperture that is highly suitable for portable quantum technology devices, including space-based experiments. The adjustability enabled an investigation into the previously unexplored impact of aperture size on the atomic flux, and optimisation of the aperture size allowed us to demonstrate a higher flux than any reported cold-atom sources that use a pyramid, LVIS, 3D-MOT or grating MOT. We achieved 2.1(1) × 1010 atoms/s of 87Rb with a mean velocity of 32(1) m/s, FWHM of 27.6(9) m/s and divergence of 59(4) mrad. Halving the total optical power to 195 mW caused only a 20% reduction of the flux, and a 30% decrease in mean velocity. Methods to further decrease the velocity as required have been identified. The low power consumption and small size make this design suitable for a wide range of cold-atom technologies.
The ongoing drive to transfer quantum technologies from research laboratories to practical, portable devices requires the development of multiple key enabling technologies. The field of cold atoms, which includes high-precision metrology and quantum simulation, has various real-world applications including time-keeping and navigation. A crucial component in these systems is a cold-atom source that generates a flux of low-velocity atoms suitable for subsequent capture. A large flux enables fast repetition rates, high duty cycles, long measurement times, and resistance to long-term performance degradation with a good signal-to-noise ratio, all of which are essential to produce cold-atom devices and technologies that are capable of out-performing the classical alternatives. This thesis presents the design, fabrication and characterisation of a novel cold-atom source using a compact pyramidal magneto-optical trap (MOT) with a unique adjustable-aperture mechanism. This allowed an investigation of the dependence of the flux characteristics on the aperture size, a parameter space that has not previously been explored. The measurements showed a strong dependence of the flux on the aperture size, with a negligible flux below 0.4mm, then an approximately linear increase up to 1.0mm, at which point the relationship showed possible signs of saturation. Using 87Rb, a flux of 1.18×1010 atoms/s was produced using a 1.27mm aperture, for which the mean velocity of the atoms was 21.6(3) m/s with a FWHM of 11.2(2) m/s, and the FWHM divergence of the beam was 86(2) mrad. This is the highest recorded flux from a pyramid or 2D+-MOT source, and amongst the highest reported fluxes from any MOT sources, and avenues for improvement still remain. This work fulfils the aim of demonstrating a compact and robust cold-atom source generating a high flux of laser-cooled atoms for real-world quantum technology applications.
We have used a pyramid magneto-optical trap (MOT) to create a compact source of cold rubidium atoms. The four dielectric-coated metal mirrors in vacuum are arranged in the form of a pyramid that creates the light field for a MOT from a single ingoing laser beam. The atoms are pushed out through a hole (aperture) in the apex of the pyramid, in a direction determined by the laser light, to give a flux of Rb-87 atoms greater than 2 × 10^10 per second with a mean velocity of 33 m/s (FWHM of 28 m/s) and a divergence of 58 mrad. The pyramid MOT has a unique mechanism for adjusting aperture size and it is highly suitable for portable quantum technology devices.
An intense cold-atom beam source based on a modified pyramidal magneto-optical trap has been developed and characterized. We have produced a slow beam of cold cesium atoms with a continuous flux of 2.2× 109 atoms/s at a mean velocity of 15 m/s and with a divergence of 15 mrad. The corresponding radiant intensity is 1.2×1013 atom s-1 sr-1. We have characterized the performance of our beam source over a range of operating conditions, and the measured values for atom flux, mean velocity, and divergence are in good agreement with results from detailed Monte Carlo numerical simulations.
A compact cold atom beam source based on a multistage two-dimensional magneto-optical trap (MOT) has been demonstrated and characterized. The multiple-stage design greatly reduces the overall size of the source apparatus while providing a high flux of atoms. The cold atom beam was used to load a separate MOT in ultrahigh vacuum, and we obtained an actual trap loading rate of 1.5 x 109 atoms/s while using only 20 mW of total laser power for the source. The entire source apparatus, including optics, can fit into a 4 cm x 4 cm x 13 cm volume.
A high-flux compact source of strontium atoms has been designed and built. We have investigated the feasibility of direct trapping of cold atoms from the atomic flux out of a hot oven. Our design uses a two-dimensional magneto-optical trap (MOT) with an additional laser beam that exerts a radiation force that is not counterbalanced to eject atoms (so-called ‘push’ beam), which is known as a 2D+ MOT configuration. This approach has been previously used for sodium, and has been extended to strontium in this work. Laser cooling of strontium typically requires multiple stages: effusion of atoms from an oven to produce an atomic beam, transverse collimation, a Zeeman slower and deflection before finally collecting atoms in a 3D MOT. A 2D+ MOT combines the Zeeman slowing, transverse collimation, and deflection into a single compact stage to provide a high-flux source suitable for applications such as matter-wave interferometry, atomic clocks and experimental studies of degenerate quantum gases. This thesis reports experimental work that has been carried out to develop and test an oven and the associated laser cooling apparatus for producing a source of cold strontium atoms which is straightforward to manufacture. We test the oven up to a temperature of To = 642 °C and measure a peak intensity of 6.8 × 1016 s−1 sr−1 and a flux of 2.9 × 1016 s−1. We typically operate the oven at To = 502 °C, for which the peak intensity and flux are 2.2 × 1015 s−1 sr−1 and 7.5 × 1014 s−1. A multi-channel nozzle made of graphite gives an angular divergence of 0.17 rad (10°) for the atomic beam. Trapping atoms directly from the thermal atomic beam into the MOT gives a maximum loading rate of 7.1 × 1010 s−1, without any laser light to repump atoms into the cooling cycle. We demonstrated a novel frequency stabilising technique for the laser by developing Zeeman-tunable modulation transfer spectroscopy in strontium with an inaccuracy of ±3.5 MHz and a frequency tuning range of 160 MHz. The initial aim of this thesis was to make a compact, high-flux strontium source suitable for quantum technology applications. During the course of this research, we participated in the preparation of a proposal for the construction of a large-scale atom interferometer based on the clock transition in strontium (87Sr) for the exploration of dark matter and gravitational waves (a project known as the Atom Interferometer Observatory and Network, AION). This changed the design requirements towards producing a higher flux (in particular of the isotope 87Sr), with compactness of the source being less important in ∼10 m scale apparatus.
Summary form only given. A simple and robust design has been implemented based on the pyramidal trap geometry which allows use of single large diameter (/spl les/20 cm) laser beam to obtain large capture rates of atoms from the background vapor. The four 45/spl deg/ mirrors are truncated just before the apex of the pyramid, and the 1 cm/sup 2/ region at the center of the incident laser beam is retro-reflected by a /spl lambda//4 plate with a high-reflectance gold coating on the second surface. A small (1 mm diameter) hole in this retro-optic forms an extraction column for the atoms while maintaining a low conductance between the source region and an adjacent UHV chamber. The characterization of this large pyramidal low-velocity intense source (LVIS) is reported, including an investigation of scaling to very large (/spl ges/10 cm) high power (/spl sim/1 W) laser beams which should allow an improvement by a factor of 2-3 in beam flux over previous reports.