Abstract Radio-frequency (RF) linear multipole traps have been shown to be very sensitive to mis-positioning of their electrodes, which results in a symmetry breaking and leads to extra local minima in the trapping potential as shown in Pedregosa-Gutierrez et al (2018 J. Mod. Opt. 65 529) disturbing the operation of the trap. In this work, we analytically describe the RF-potential of a realistic octupole trap by including lower order terms to the well-established equation for a perfectly symmetric octupole trap. We describe the geometry by a combination of identified defects, characterized by simple analytical expressions. A complete equation is proposed for a trap with any electrode deviation relying on a combination of the simple cases where the defects are taken individually. Our approach is validated by comparison between analytical and numerical results for defect sizes up to 4% of the trap radius. As described in Pedregosa-Gutierrez et al (2018 Rev. Sci. Instrum. 89 123101), an independent fine-tuning of the amplitude of the RF voltage applied on each electrode can be used to mitigate the geometrical defects of a realistic trap. In a different way than in Pedregosa-Gutierrez et al (2018 Rev. Sci. Instrum. 89 123101), the knowledge of an analytical equation for the potential allows to design the set of RF-voltages required for this compensation, based on the experimental measurement of the ion positions in the trap, without information concerning the exact position of each electrode, and with a small number of iterations. The requirements, performances and limitations of this protocol are discussed via comparison of numerical simulations and analytical results.
Abstract Radio-frequency (RF) linear multipole traps have been shown to be very sensitive to mis-positioning of their electrodes, which results in a symmetry breaking and leads to extra local minima in the trapping potential as shown in Pedregosa-Gutierrez et al (2018 J. Mod. Opt. 65 529) disturbing the operation of the trap. In this work, we analytically describe the RF-potential of a realistic octupole trap by including lower order terms to the well-established equation for a perfectly symmetric octupole trap. We describe the geometry by a combination of identified defects, characterized by simple analytical expressions. A complete equation is proposed for a trap with any electrode deviation relying on a combination of the simple cases where the defects are taken individually. Our approach is validated by comparison between analytical and numerical results for defect sizes up to 4% of the trap radius. As described in Pedregosa-Gutierrez et al (2018 Rev. Sci. Instrum. 89 123101), an independent fine-tuning of the amplitude of the RF voltage applied on each electrode can be used to mitigate the geometrical defects of a realistic trap. In a different way than in Pedregosa-Gutierrez et al (2018 Rev. Sci. Instrum. 89 123101), the knowledge of an analytical equation for the potential allows to design the set of RF-voltages required for this compensation, based on the experimental measurement of the ion positions in the trap, without information concerning the exact position of each electrode, and with a small number of iterations. The requirements, performances and limitations of this protocol are discussed via comparison of numerical simulations and analytical results.
Multipole radio-frequency (RF) traps are central to collisional experiments in cryogenic environments. They also offer possibilities to generate new type of ion crystals topologies and in particular the potential to create infinite 1D/2D structures: ion rings and ion tubes. However, multipole traps have also been shown to be very sensitive to geometrical misalignment of the trap rods, leading to additional local trapping minima. The present work proposes a method to correct non-ideal potentials, by modifying the applied RF amplitudes for each trap rod. This approach is discussed for the octupole trap, leading to the restitution of the ideal Mexican-Hat-like pseudo-potential, expected in multipole traps. The goodness of the compensation method is quantified in terms of the choice of the diagnosis area, the residual trapping potential variations, the required adaptation of the applied RF voltage amplitudes, and the impact on the trapped ion structures. Experimental implementation for macroscopic multipole traps is also discussed, in order to propose a diagnostic method with respect to the resolution and stability of the trap drive. Using the proposed compensation technique, we discuss the feasibility of generating a homogeneous ion ring crystal, which is a measure of quality for the obtained potential well.
Radiofrequency multipole traps have been used for some decades in cold collision experiments and are gaining interest for precision spectroscopy due to their low micromotion contribution and the predicted unusual cold-ion structures. However, the experimental realisation is not yet fully controlled, and open questions in the operation of these devices remain. We present experimental observations of symmetry breaking of the trapping potential in a macroscopic octupole trap with laser-cooled ions. Numerical simulations have been performed in order to explain the appearance of additional local potential minima and be able to control them in a next step. We characterise these additional potential minima, in particular with respect to their position, their potential depth and their probability of population as a function of the radial and angular displacement of the trapping rods.
With the increasing number of ion qubits and improving performance of sophisticated quantum algorithms, more and more scalable complex ion trap electrodes have been developed and integrated. Nonlinear ion shuttling operations at the junction are more frequently used, such as in the areas of separation, merging, and exchanging. Several studies have been conducted to optimize the geometries of the radio-frequency (RF) electrodes to generate ideal trapping electric fields with a lower junction barrier and an even ion height of the RF saddle points. However, this iteration is time-consuming and commonly accompanied by complicated and sharp electrode geometry. Therefore, high-accuracy fabrication process and high electric breakdown voltage are essential. In the current work, an effective method was proposed to reduce the junction's pseudo-potential barrier and ion height variation by setting several individual RF electrodes and adjusting each RF voltage amplitude without changing the geometry of the electrode structure. The simulation results show that this method shows the same effect on engineering the trapping potential and reducing the potential barrier, but requires fewer parameters and optimization time. By combining this method with the geometrical shape-optimizing, the pseudo-potential barrier and the ion height variation near the junction can be further reduced. In addition, the geometry of the electrodes can be simplified to relax the fabrication precision and keep the ability to engineer the trapping electric field in real-time even after the fabrication of the electrodes, which provides a potential all-electric degree of freedom for the design and control of the two-dimensional ion crystals and investigation of their phase transition.
Surface-electrode (SE) rf traps are a promising approach to manufacturing complex ion-trap networks suitable for large-scale quantum information processing. In this paper we present analytical methods for modeling SE traps in the gapless plane approximation, and apply these methods to two particular classes of SE traps. For the SE ring trap we derive analytical expressions for the trap geometry and strength, and also calculate the depth in the absence of control fields. For translationally symmetric multipole configurations (analogs of the linear Paul trap), we derive analytical expressions for electrode geometry and strength. Further, we provide arbitrarily good approximations of the trap depth in the absence of static fields and identify the requirements for obtaining maximal depth. Lastly, we show that the depth of SE multipoles can be greatly influenced by control fields.
The accurate characterization of the spatial electric field generated by electrodes in a surface electrode trap is of paramount importance. In this pursuit, we have identified a simple yet highly precise parametric expression to describe the spatial field of a rectangular-shaped electrode. Leveraging this expression, we introduced an optimization method designed to accurately characterize the axial electric field intensity produced by the powered electrode and the stray field. Distinct from the existing methods, our approach integrates a diverse array of experimental data, including the equilibrium positions of ions in a linear string, the equilibrium positions of single trapped ions, and trap frequencies, to effectively reduce the systematic errors. This approach provides considerable flexibility in voltage settings for data acquisition, making it especially advantageous for surface electrode traps where the trapping height of ion probes may vary with casual voltage settings. In our experimental demonstration, we successfully minimized the discrepancy between observations and model predictions to a remarkable degree. The relative errors of secular frequencies were contained within ±0.5%, and the positional error of ions was constrained to less than 1.2 μm, which surpasses the performance of current methodologies.
Ion traps are a foundational technology in quantum information processing, precision spectroscopy and foundational physics tests. At the heart of their performance is the inhibition of micromotion, an oscillation of ions through imperfect trapping potentials, that restricts the laser cooling efficiency, coherence times, and the accuracy of measurements. The paper provides a systematic computational analysis of four different electrode geometries (Linear Paul, Segmented, Surface and Ring) in 24 different RF / DC configurations (C01-C24) and 13 performance parameters that comprise trap depth (0.62 1.48 eV), radial secular frequency (1,100 1 Multi-objective optimization with weighted scoring of these metrics indicates that Ring trap geometry scores the highest total (80.2/100), followed by Linear Paul (72.0), Segmented (67.0) and Surface (55.1) configurations. ANOVA (one-way) statistically verified the presence of statistically significant inter-geometry differences in micro-motions amplitude (F = 18.43, p < .001) and cooling efficiency (F = 22.17, p < .001), with Tukey HSD post-hoc revealed that the most significant difference was between the Ring and the Surface. The Pearson correlation analysis shows that RF drive voltage and micromotion amplitude (r = -0.94 to -0.99) and cooling efficiency and micromotion (r = -1.00) have near-perfect inverse correlations, which prove that the quality of confinement is regulated by electrode geometry, RF amplitude, and spacing. These results give quantitative design principles of next-generation ion traps in quantum computing and atomic clock. Keywords: ion trap, micromotion minimization, RF/DC electrode optimization, laser cooling, Mathieu stability, secular frequency, quantum computing