Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1902.02728 · Optics Express

Spectral noise in frequency conversion from the visible to the telecommunication C-band

Peter C. Strassmann, Anthony Martin, Nicolas Gisin, Mikael Afzelius

Published May 2, 2019• 28 citations
arXivHTMLPDF

Abstract

We report a detailed study of the noise properties of a visible-to-telecom photon frequency converter based on difference frequency generation (DFG). The device converts 580 nm photons to 1541 nm using a strong pump laser at 930 nm, in a periodically poled lithium niobate ridge waveguide. The converter reaches a maximum device efficiency of 46 % (internal efficiency of 67%) at a pump power of 250 mW. The noise produced by the pump laser is investigated in detail by recording the noise spectra both in the telecom and visible regimes and measuring the power dependence of the noise rates. The noise spectrum in the telecom is very broadband, as expected from previous work on similar DFG converters. However, we also observe several narrow dips in the telecom spectrum, with corresponding peaks appearing in the 580 nm noise spectrum. These features are explained by sum frequency generation of the telecom noise at wavelengths given by the phase-matching condition of different spatial modes in the waveguide. The proposed noise model is in good agreement with all the measured data, including the power dependence of the noise rates, both in the visible and telecom regimes. These results are applicable to the class of DFG converters where the pump laser wavelength is in between the input and target wavelength.

DOI
10.1364/oe.27.014298

Related papers

Frequency down-conversion of 637 nm light to the telecommunication band for non-classical light emitted from NV centers in diamond

Rikizo Ikuta, Toshiki Kobayashi, Shuto Yasui +9 more

We demonstrate a low-noise frequency down-conversion of photons at 637 nm to the telecommunication band at 1587 nm by the difference frequency generation in a periodically-poled lithium niobate. An internal conversion efficiency of the converter is estimated to be 0.44 at the maximum which is achieved by a pump power of 0.43 W, whereas a rate of internal background photons caused by the strong cw pump laser is estimated to be 9 kHz/mW within a bandwidth of about 1 nm. By using the experimental values related to the intrinsic property of the converter, and using the intensity correlation and the average photon number of a 637 nm input light pulse, we derive the intensity correlation of a converted telecom light pulse. Then we discuss feasibility of a single-photon frequency conversion to the telecommunication band for a long-distance quantum communication based on NV centers in diamond.

arXiv:1402.2944•Optics Express•May 1, 2014•38 citations

Proposal for noise-free visible-telecom quantum frequency conversion through third-order sum and difference frequency generation

Xiyuan Lu, Gregory T. Moille, Ashutosh Rao +1 more

Quantum frequency conversion (QFC) between the visible and telecom is a key to connect quantum memories in fiber-based quantum networks. Current methods for linking such widely separated frequencies, such as sum/difference frequency generation and four-wave mixing Bragg scattering, are prone to broadband noise generated by the pump laser(s). To address this issue, we propose to use third-order sum/difference frequency generation (TSFG/TDFG) for an upconversion/downconversion QFC interface. In this process, two long wavelength pump photons combine their energy and momentum to mediate frequency conversion across the large spectral gap between the visible and telecom bands, which is particularly beneficial from the noise perspective. We show that waveguide-coupled silicon nitride microring resonators can be designed for efficient QFC between 606 and 1550 nm via a 1990 nm pump through TSFG/TDFG. We simulate the device dispersion and coupling, and from the simulated parameters, estimate that the frequency conversion can be efficient (${\gt}80 \%$) at 50 mW pump power. Our results suggest that microresonator TSFG/TDFG is promising for compact, scalable, and low-power QFC across large spectral gaps.

arXiv:2010.06811•Optics Letters•Dec 7, 2020•11 citations

All-Optical Wavelength Conversion Based on the Cascaded Sum and Difference Frequency Generation in a Periodically Poled Lithium-Niobate Waveguide

Jian Wang

The principle of all-optical wavelength conversion based on the cascaded sum and difference frequency generation (SFG+DFG) in quasi-phase-matched (QPM) periodically poled LiNbO3 (PPLN) waveguides is introduced. The conversion efficiency of the wavelength converter is calculated. The influences of the powers and span of two pumps on the conversion efficiency are analyzed. Bandwidth of one pump wavelength is discussed. The tuning is about 0.5 nm. The signal pulse width is compressed about 0.68 times.

Optics & Optoelectronic Technology•Jan 1, 2007•0 citations

Quantum frequency conversion of memory-compatible single photons from 606 nm to the telecom C-band

Nicolas Maring, Dario Lago-Rivera, Andreas Lenhard +2 more

We report on quantum frequency conversion of memory-compatible narrow-bandwidth photons at 606 nm to the telecom C-band at 1552$\,$nm. The 200$\,$ns long photons, compatible with Praseodymium-based solid-state quantum memories are frequency converted using a single-step difference frequency generation process in a periodically poled Lithium Niobate waveguide. We characterize the noise processes involved in the conversion and by applying strong spectral filtering of the noise, we demonstrate high signal-to-noise ratio conversion at the single photon level (SNR$\,>\,$100 for a mean input photon number per pulse of 1). We finally observe that a memory compatible heralded single photon with a bandwidth of 1.8$\,$MHz, obtained from a spontaneous parametric down conversion pair source, still shows a strong non-classical behavior after conversion. We first demonstrate that correlations between heralding and converted heralded photons stay in the non-classical regime. Moreover, we measured the heralded autocorrelation function of the heralded photon using the converter device as a frequency-domain beam splitter, yielding a value of $0.19\pm0.07$. The presented work represents a step towards the connection of several quantum memory systems emitting narrow-band visible photons to the telecommunication wavelengths.

arXiv:1801.03727•Optica•Apr 25, 2018•83 citations

Frequency conversion between UV and telecom wavelengths in a lithium niobate waveguide for quantum communication with Yb + trapped ions

Sachin Kasture, Francesco Lenzini, Ben Haylock +4 more

Abstract We study and demonstrate the frequency conversion of UV radiation, resonant with 369.5 nm transition in Yb + ions to the C-band wavelength 1580.3 nm and vice-versa using a reverse proton-exchanged waveguide in periodically poled lithium niobate. Our integrated device can interface trapped Yb + ions with a telecom infrastructure for the realization of an Yb + based quantum repeater protocol and to efficiently distribute entanglement over long distances. We analyse the single photon frequency conversion efficiency from the 369.525 nm to the telecom wavelength and its dependence on pump power, device length and temperature. The single-photon noise generated by the spontaneous Raman scattering of the pump is also measured. From this analysis we estimate a single photon conversion efficiency of ∼9% is achievable with our technology with almost complete suppression of the Raman noise.

arXiv:1606.08127•Journal of Optics•Sep 22, 2016•35 citations

Low-noise cascaded frequency conversion of 637.2 nm light to the telecommunication C-band in a single-waveguide device

Fabrice von Chamier, Joscha Hanel, Chris Müller +3 more

Interconnected quantum devices are the building blocks of quantum networks, where state transduction plays a central role. The frequency conversion of photons into the telecommunication C-band is decisive in taking advantage of current low-loss transmission lines. Here, we report the difference frequency conversion of 637.2 nm fluorescent light from a cluster of NV centers in diamond to tunable wavelengths between 1559.0 nm and 1564.9 nm. In order to avoid detrimental noise from spontaneous emissions, we use a two-step conversion device based on a single-pumped periodically poled lithium niobate waveguide. We observed a total external (internal) conversion efficiency of 3.0 ± 0.1 (20.5 ± 0.8) % with a noise rate of 2.4 ± 0.8 (16 ± 5) cps/GHz.

arXiv:2502.14557•Optics Express•Apr 15, 2025•5 citations
We report a detailed study of the noise properties of a visible-to-telecom photon frequency converter based on difference frequency generation (DFG). The device converts 580 nm photons to 1541 nm using a strong pump laser at 930 nm, in a periodically poled lithium niobate ridge waveguide. The converter reaches a maximum device efficiency of 46 % (internal efficiency of 67%) at a pump power of 250 mW. The noise produced by the pump laser is investigated in detail by recording the noise spectra both in the telecom and visible regimes and measuring the power dependence of the noise rates. The noise spectrum in the telecom is very broadband, as expected from previous work on similar DFG converters. However, we also observe several narrow dips in the telecom spectrum, with corresponding peaks appearing in the 580 nm noise spectrum. These features are explained by sum frequency generation of the telecom noise at wavelengths given by the phase-matching condition of different spatial modes in the waveguide. The proposed noise model is in good agreement with all the measured data, including the power dependence of the noise rates, both in the visible and telecom regimes. These results are applicable to the class of DFG converters where the pump laser wavelength is in between the input and target wavelength.
We demonstrate a low-noise frequency down-conversion of photons at 637 nm to the telecommunication band at 1587 nm by the difference frequency generation in a periodically-poled lithium niobate. An internal conversion efficiency of the converter is estimated to be 0.44 at the maximum which is achieved by a pump power of 0.43 W, whereas a rate of internal background photons caused by the strong cw pump laser is estimated to be 9 kHz/mW within a bandwidth of about 1 nm. By using the experimental values related to the intrinsic property of the converter, and using the intensity correlation and the average photon number of a 637 nm input light pulse, we derive the intensity correlation of a converted telecom light pulse. Then we discuss feasibility of a single-photon frequency conversion to the telecommunication band for a long-distance quantum communication based on NV centers in diamond.
Quantum frequency conversion (QFC) between the visible and telecom is a key to connect quantum memories in fiber-based quantum networks. Current methods for linking such widely separated frequencies, such as sum/difference frequency generation and four-wave mixing Bragg scattering, are prone to broadband noise generated by the pump laser(s). To address this issue, we propose to use third-order sum/difference frequency generation (TSFG/TDFG) for an upconversion/downconversion QFC interface. In this process, two long wavelength pump photons combine their energy and momentum to mediate frequency conversion across the large spectral gap between the visible and telecom bands, which is particularly beneficial from the noise perspective. We show that waveguide-coupled silicon nitride microring resonators can be designed for efficient QFC between 606 and 1550 nm via a 1990 nm pump through TSFG/TDFG. We simulate the device dispersion and coupling, and from the simulated parameters, estimate that the frequency conversion can be efficient (>80%{\gt}80 \%>80%) at 50 mW pump power. Our results suggest that microresonator TSFG/TDFG is promising for compact, scalable, and low-power QFC across large spectral gaps.
The principle of all-optical wavelength conversion based on the cascaded sum and difference frequency generation (SFG+DFG) in quasi-phase-matched (QPM) periodically poled LiNbO3 (PPLN) waveguides is introduced. The conversion efficiency of the wavelength converter is calculated. The influences of the powers and span of two pumps on the conversion efficiency are analyzed. Bandwidth of one pump wavelength is discussed. The tuning is about 0.5 nm. The signal pulse width is compressed about 0.68 times.
We report on quantum frequency conversion of memory-compatible narrow-bandwidth photons at 606 nm to the telecom C-band at 1552 \,nm. The 200 \,ns long photons, compatible with Praseodymium-based solid-state quantum memories are frequency converted using a single-step difference frequency generation process in a periodically poled Lithium Niobate waveguide. We characterize the noise processes involved in the conversion and by applying strong spectral filtering of the noise, we demonstrate high signal-to-noise ratio conversion at the single photon level (SNR$\,>\,100forameaninputphotonnumberperpulseof1).Wefinallyobservethatamemorycompatibleheraldedsinglephotonwithabandwidthof1.8100 for a mean input photon number per pulse of 1). We finally observe that a memory compatible heralded single photon with a bandwidth of 1.8100forameaninputphotonnumberperpulseof1).Wefinallyobservethatamemorycompatibleheraldedsinglephotonwithabandwidthof1.8\,$MHz, obtained from a spontaneous parametric down conversion pair source, still shows a strong non-classical behavior after conversion. We first demonstrate that correlations between heralding and converted heralded photons stay in the non-classical regime. Moreover, we measured the heralded autocorrelation function of the heralded photon using the converter device as a frequency-domain beam splitter, yielding a value of 0.19±0.070.19\pm0.070.19±0.07. The presented work represents a step towards the connection of several quantum memory systems emitting narrow-band visible photons to the telecommunication wavelengths.
Abstract We study and demonstrate the frequency conversion of UV radiation, resonant with 369.5 nm transition in Yb + ions to the C-band wavelength 1580.3 nm and vice-versa using a reverse proton-exchanged waveguide in periodically poled lithium niobate. Our integrated device can interface trapped Yb + ions with a telecom infrastructure for the realization of an Yb + based quantum repeater protocol and to efficiently distribute entanglement over long distances. We analyse the single photon frequency conversion efficiency from the 369.525 nm to the telecom wavelength and its dependence on pump power, device length and temperature. The single-photon noise generated by the spontaneous Raman scattering of the pump is also measured. From this analysis we estimate a single photon conversion efficiency of ∼9% is achievable with our technology with almost complete suppression of the Raman noise.
Interconnected quantum devices are the building blocks of quantum networks, where state transduction plays a central role. The frequency conversion of photons into the telecommunication C-band is decisive in taking advantage of current low-loss transmission lines. Here, we report the difference frequency conversion of 637.2 nm fluorescent light from a cluster of NV centers in diamond to tunable wavelengths between 1559.0 nm and 1564.9 nm. In order to avoid detrimental noise from spontaneous emissions, we use a two-step conversion device based on a single-pumped periodically poled lithium niobate waveguide. We observed a total external (internal) conversion efficiency of 3.0 ± 0.1 (20.5 ± 0.8) % with a noise rate of 2.4 ± 0.8 (16 ± 5) cps/GHz.