Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1809.06964 · Physical Review Letters

Gated Conditional Displacement Readout of Superconducting Qubits

Steven Touzard, Angela Kou, Nicholas Frattini, Volodymyr Sivak, Shruti Puri, Alexander Grimm, Luigi Frunzio, Shyam Shankar, Michel Devoret

Published Feb 25, 2019• 143 citations
arXivHTMLPDF

Abstract

We have realized a new interaction between superconducting qubits and a readout cavity that results in the displacement of a coherent state in the cavity, conditioned on the state of the qubit. This conditional state, when it reaches the cavity-following, phase-sensitive amplifier, matches its measured observable, namely, the in phase quadrature. In a setup where several qubits are coupled to the same readout resonator, we show it is possible to measure the state of a target qubit with minimal dephasing of the other qubits. Our results suggest novel directions for faster readout of superconducting qubits and implementations of bosonic quantum error-correcting codes.

DOI
10.1103/physrevlett.122.080502

Related papers

Entanglement and Quantum Error Correction with Superconducting Qubits

Matthew Reed

A quantum computer will use the properties of quantum physics to solve certain computational problems much faster than otherwise possible. One promising potential implementation is to use superconducting quantum bits in the circuit quantum electrodynamics (cQED) architecture. There, the low energy states of a nonlinear electronic oscillator are isolated and addressed as a qubit. These qubits are capacitively coupled to the modes of a microwave-frequency transmission line resonator which serves as a quantum communication bus. Microwave electrical pulses are applied to the resonator to manipulate or measure the qubit state. State control is calibrated using diagnostic sequences that expose systematic errors. Hybridization of the resonator with the qubit gives it a nonlinear response when driven strongly, useful for amplifying the measurement signal to enhance accuracy. Qubits coupled to the same bus may coherently interact with one another via the exchange of virtual photons. A two-qubit conditional phase gate mediated by this interaction can deterministically entangle its targets, and is used to generate two-qubit Bell states and three-qubit GHZ states. These three-qubit states are of particular interest because they redundantly encode quantum information. They are the basis of the quantum repetition code prototypical of more sophisticated schemes required for quantum computation. Using a three-qubit Toffoli gate, this code is demonstrated to autonomously correct either bit- or phase-flip errors. Despite observing the expected behavior, the overall fidelity is low because of decoherence. A superior implementation of cQED replaces the transmission-line resonator with a three-dimensional box mode, increasing lifetimes by an order of magnitude. In-situ qubit frequency control is enabled with control lines, which are used to fully characterize and control the system Hamiltonian.

arXiv:1311.6759•Bulletin of the American Physical Society•Nov 26, 2013•72 citations

Enhancing qubit readout fidelity with two-mode squeezing of the coherent measurement signal

Baleegh Abdo, William Shanks, Oblesh Jinka +1 more

The ability to perform high-fidelity quantum nondemolition qubit readout is pivotal for the realization of large and powerful quantum computers. Such readout of superconducting qubits is generally enabled by amplifying the weak dispersive measurement signals using phase-preserving quantum-limited Josephson amplifiers with sufficient gain to dilute the contribution of the added noise by the output chain. Here, we further enhance the qubit readout fidelity by (1) simultaneously measuring the two-mode squeezed states of the amplified readout signals at the signal and idler frequencies of the nondegenerate amplifier and (2) coherently combining them at the classical processing stage following a relative rotation that maximizes the signal to noise ratio of the qubit-encoded readout quadrature. Such readout scheme exhibits enhancement in the readout fidelity for all practical values of amplifier gain and noise added by the output chain and is fully compatible with frequency multiplexed setups used in large quantum processors.

quant-pharXiv:2603.15804•EPJ Quantum Technology•Mar 18, 2026•0 citations

Recovering Quantum Coherence of a Cavity Qubit Coupled to a Noisy Ancilla through Real-Time Feedback

Uri Goldblatt, Nitzan Kahn, Sergey Hazanov +6 more

Decoherence in qubits, caused by their interaction with a noisy environment, poses a significant challenge to the development of reliable quantum processors. A prominent source of errors arises from noise in coupled ancillas, which can quickly spread to qubits. By actively monitoring these noisy ancillas, it is possible to not only identify qubit decoherence events but also to correct these errors in real time. This approach is particularly beneficial for bosonic qubits, where the interaction with ancillas is a dominant source of decoherence. In this work, we uncover the intricate dynamics of decoherence in a superconducting cavity qubit due to its interaction with a noisy transmon ancilla. By tracking the noisy ancilla trajectory and using real-time feedback, we successfully recover the lost coherence of the cavity qubit, achieving a fivefold increase in its pure dephasing time. Additionally, by detecting ancilla errors and converting them into erasures, we improve the pure dephasing time by more than an order of magnitude. These advances are essential for realizing long-lived cavity qubits with high-fidelity gates, and they pave the way for more efficient bosonic quantum error-correction codes. Published by the American Physical Society 2024

arXiv:2403.02081•Physical Review X•Dec 5, 2024•6 citations

Observation of Quantum Oscillations between a Josephson Phase Qubit and a Microscopic Resonator Using Fast Readout

Ken B. Cooper, Matthias Steffen, Robert McDermott +5 more

We have detected coherent quantum oscillations between Josephson phase qubits and critical-current fluctuators by implementing a new state readout technique that is an order of magnitude faster than previous methods. These results reveal a new aspect of the quantum behavior of Josephson junctions, and they demonstrate the means to measure two-qubit interactions in the time domain. The junction-fluctuator interaction also points to a possible mechanism for decoherence and reduced fidelity in superconducting qubits.

arXiv:cond-mat/0405710•Physical Review Letters•Oct 25, 2004•243 citations

Measuring the decoherence of a quantronium qubit with the cavity bifurcation amplifier

Michael Metcalfe, Etienne Boaknin, Vladimir Manucharyan +6 more

Dispersive readouts for superconducting qubits have the advantage of speed and minimal invasiveness. We have developed such an amplifier, the cavity bifurcation amplifier (CBA), and applied it to the readout of the quantronium qubit. It consists of a Josephson junction embedded in a microwave on-chip resonator. In contrast with the Josephson bifurcation amplifier, which has an on-chip capacitor shunting a junction, the resonator is based on a simple coplanar waveguide imposing a predetermined frequency and whose other rf characteristics such as the quality factor are easily controlled and optimized. Under proper microwave irradiation conditions, the CBA has two metastable states. Which state is adopted by the CBA depends on the state of a quantronium qubit coupled to the CBA's junction. Due to the megahertz repetition rate and large signal to noise ratio, we can show directly that the coherence is limited by $1∕f$ gate charge noise when biased at the ``sweet spot''---a point insensitive to first order gate charge fluctuations. This architecture lends itself to scalable quantum computing using a multiresonator chip with multiplexed readouts.

arXiv:0706.0765•Physical Review B•Nov 21, 2007•76 citations

Implementation of Microwave-Activated Conditional Quantum Operations in Superconducting Circuits

菖太郎 白井

There are two main approaches to correcting errors during quantum computation.The first one is redundantly embedding the degrees of freedom of a single qubit into multiple qubits.The second is known as bosonic codes, a method that embeds the information of a single qubit into a single multi-level system, such as a harmonic oscillator, using an auxiliary qubit.For the former, it is essential to implement quantum operations with low wiring costs and develop an architecture robust to parameter variations during fabrication steps.For the latter, it is necessary to establish a state manipulation method that does not degrade the coherence of the harmonic oscillator.Keeping these challenges in mind, we consulted on the research and obtained the following results.To achieve high-precision control in superconducting circuits, it is essential to establish a fabrication recipe for superconducting circuit elements with sufficiently long coherence times.We achieved state-of-the-art coherence times exceeding 400 µs of transmon qubits using high-temperature-grown Titanium Nitride superconducting thin films on silicon substrates.This result was achieved by optimizing the fabrication recipe and design of the superconducting circuit.Using a microwave-activated interaction with a fixed-frequency transmon qubit as a coupler, we developed a controlled-Z gate between transmon qubits.This method does not require frequency tunability of the qubits, and it maintains the advantages of fixed-frequency transmon qubits, such as long coherence time and low wiring cost, while minimizing the always-on residual ZZ interaction, which causes coherent errors, compared to conventional methods.This gate architecture offers higher design freedom and tolerance to parameter variations during fabrication steps.We implemented a conditional displacement gate between an auxiliary qubit and a resonator.Previously, in superconducting circuits, a weak dispersive coupling between the resonator and transmon qubit is primarily used as a resource interaction for the conditional displacement gate.Unfortunately, this valuable control resource can be a bit-flip error propagation channel during conditional gate operations.To address this issue, we implemented artificial spin-dependent forces (SDF) interaction between a superconducting resonator and a cubic transmon, offering second-order nonlinearity as a resource of SDF interaction.Using this interaction, we successfully prepared the superconducting resonator's squeezed vacuum and cat states.i

•Mar 21, 2024•0 citations
We have realized a new interaction between superconducting qubits and a readout cavity that results in the displacement of a coherent state in the cavity, conditioned on the state of the qubit. This conditional state, when it reaches the cavity-following, phase-sensitive amplifier, matches its measured observable, namely, the in phase quadrature. In a setup where several qubits are coupled to the same readout resonator, we show it is possible to measure the state of a target qubit with minimal dephasing of the other qubits. Our results suggest novel directions for faster readout of superconducting qubits and implementations of bosonic quantum error-correcting codes.
A quantum computer will use the properties of quantum physics to solve certain computational problems much faster than otherwise possible. One promising potential implementation is to use superconducting quantum bits in the circuit quantum electrodynamics (cQED) architecture. There, the low energy states of a nonlinear electronic oscillator are isolated and addressed as a qubit. These qubits are capacitively coupled to the modes of a microwave-frequency transmission line resonator which serves as a quantum communication bus. Microwave electrical pulses are applied to the resonator to manipulate or measure the qubit state. State control is calibrated using diagnostic sequences that expose systematic errors. Hybridization of the resonator with the qubit gives it a nonlinear response when driven strongly, useful for amplifying the measurement signal to enhance accuracy. Qubits coupled to the same bus may coherently interact with one another via the exchange of virtual photons. A two-qubit conditional phase gate mediated by this interaction can deterministically entangle its targets, and is used to generate two-qubit Bell states and three-qubit GHZ states. These three-qubit states are of particular interest because they redundantly encode quantum information. They are the basis of the quantum repetition code prototypical of more sophisticated schemes required for quantum computation. Using a three-qubit Toffoli gate, this code is demonstrated to autonomously correct either bit- or phase-flip errors. Despite observing the expected behavior, the overall fidelity is low because of decoherence. A superior implementation of cQED replaces the transmission-line resonator with a three-dimensional box mode, increasing lifetimes by an order of magnitude. In-situ qubit frequency control is enabled with control lines, which are used to fully characterize and control the system Hamiltonian.
The ability to perform high-fidelity quantum nondemolition qubit readout is pivotal for the realization of large and powerful quantum computers. Such readout of superconducting qubits is generally enabled by amplifying the weak dispersive measurement signals using phase-preserving quantum-limited Josephson amplifiers with sufficient gain to dilute the contribution of the added noise by the output chain. Here, we further enhance the qubit readout fidelity by (1) simultaneously measuring the two-mode squeezed states of the amplified readout signals at the signal and idler frequencies of the nondegenerate amplifier and (2) coherently combining them at the classical processing stage following a relative rotation that maximizes the signal to noise ratio of the qubit-encoded readout quadrature. Such readout scheme exhibits enhancement in the readout fidelity for all practical values of amplifier gain and noise added by the output chain and is fully compatible with frequency multiplexed setups used in large quantum processors.
Decoherence in qubits, caused by their interaction with a noisy environment, poses a significant challenge to the development of reliable quantum processors. A prominent source of errors arises from noise in coupled ancillas, which can quickly spread to qubits. By actively monitoring these noisy ancillas, it is possible to not only identify qubit decoherence events but also to correct these errors in real time. This approach is particularly beneficial for bosonic qubits, where the interaction with ancillas is a dominant source of decoherence. In this work, we uncover the intricate dynamics of decoherence in a superconducting cavity qubit due to its interaction with a noisy transmon ancilla. By tracking the noisy ancilla trajectory and using real-time feedback, we successfully recover the lost coherence of the cavity qubit, achieving a fivefold increase in its pure dephasing time. Additionally, by detecting ancilla errors and converting them into erasures, we improve the pure dephasing time by more than an order of magnitude. These advances are essential for realizing long-lived cavity qubits with high-fidelity gates, and they pave the way for more efficient bosonic quantum error-correction codes. Published by the American Physical Society 2024
We have detected coherent quantum oscillations between Josephson phase qubits and critical-current fluctuators by implementing a new state readout technique that is an order of magnitude faster than previous methods. These results reveal a new aspect of the quantum behavior of Josephson junctions, and they demonstrate the means to measure two-qubit interactions in the time domain. The junction-fluctuator interaction also points to a possible mechanism for decoherence and reduced fidelity in superconducting qubits.
Dispersive readouts for superconducting qubits have the advantage of speed and minimal invasiveness. We have developed such an amplifier, the cavity bifurcation amplifier (CBA), and applied it to the readout of the quantronium qubit. It consists of a Josephson junction embedded in a microwave on-chip resonator. In contrast with the Josephson bifurcation amplifier, which has an on-chip capacitor shunting a junction, the resonator is based on a simple coplanar waveguide imposing a predetermined frequency and whose other rf characteristics such as the quality factor are easily controlled and optimized. Under proper microwave irradiation conditions, the CBA has two metastable states. Which state is adopted by the CBA depends on the state of a quantronium qubit coupled to the CBA's junction. Due to the megahertz repetition rate and large signal to noise ratio, we can show directly that the coherence is limited by 1∕f1∕f1∕f gate charge noise when biased at the ``sweet spot''---a point insensitive to first order gate charge fluctuations. This architecture lends itself to scalable quantum computing using a multiresonator chip with multiplexed readouts.
There are two main approaches to correcting errors during quantum computation.The first one is redundantly embedding the degrees of freedom of a single qubit into multiple qubits.The second is known as bosonic codes, a method that embeds the information of a single qubit into a single multi-level system, such as a harmonic oscillator, using an auxiliary qubit.For the former, it is essential to implement quantum operations with low wiring costs and develop an architecture robust to parameter variations during fabrication steps.For the latter, it is necessary to establish a state manipulation method that does not degrade the coherence of the harmonic oscillator.Keeping these challenges in mind, we consulted on the research and obtained the following results.To achieve high-precision control in superconducting circuits, it is essential to establish a fabrication recipe for superconducting circuit elements with sufficiently long coherence times.We achieved state-of-the-art coherence times exceeding 400 µs of transmon qubits using high-temperature-grown Titanium Nitride superconducting thin films on silicon substrates.This result was achieved by optimizing the fabrication recipe and design of the superconducting circuit.Using a microwave-activated interaction with a fixed-frequency transmon qubit as a coupler, we developed a controlled-Z gate between transmon qubits.This method does not require frequency tunability of the qubits, and it maintains the advantages of fixed-frequency transmon qubits, such as long coherence time and low wiring cost, while minimizing the always-on residual ZZ interaction, which causes coherent errors, compared to conventional methods.This gate architecture offers higher design freedom and tolerance to parameter variations during fabrication steps.We implemented a conditional displacement gate between an auxiliary qubit and a resonator.Previously, in superconducting circuits, a weak dispersive coupling between the resonator and transmon qubit is primarily used as a resource interaction for the conditional displacement gate.Unfortunately, this valuable control resource can be a bit-flip error propagation channel during conditional gate operations.To address this issue, we implemented artificial spin-dependent forces (SDF) interaction between a superconducting resonator and a cubic transmon, offering second-order nonlinearity as a resource of SDF interaction.Using this interaction, we successfully prepared the superconducting resonator's squeezed vacuum and cat states.i