Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:0706.0765 · Physical Review B

Measuring the decoherence of a quantronium qubit with the cavity bifurcation amplifier

Michael Metcalfe, Etienne Boaknin, Vladimir Manucharyan, Rajamani Vijay, Irfan A. Siddiqi, Chad T. Rigetti, Luigi Frunzio, Robert J. Schoelkopf, Michel Devoret

Published Nov 21, 2007• 76 citations
arXivHTMLPDF

Abstract

Dispersive readouts for superconducting qubits have the advantage of speed and minimal invasiveness. We have developed such an amplifier, the cavity bifurcation amplifier (CBA), and applied it to the readout of the quantronium qubit. It consists of a Josephson junction embedded in a microwave on-chip resonator. In contrast with the Josephson bifurcation amplifier, which has an on-chip capacitor shunting a junction, the resonator is based on a simple coplanar waveguide imposing a predetermined frequency and whose other rf characteristics such as the quality factor are easily controlled and optimized. Under proper microwave irradiation conditions, the CBA has two metastable states. Which state is adopted by the CBA depends on the state of a quantronium qubit coupled to the CBA's junction. Due to the megahertz repetition rate and large signal to noise ratio, we can show directly that the coherence is limited by $1∕f$ gate charge noise when biased at the ``sweet spot''---a point insensitive to first order gate charge fluctuations. This architecture lends itself to scalable quantum computing using a multiresonator chip with multiplexed readouts.

DOI
10.1103/physrevb.76.174516

Related papers

Dispersive measurements of superconducting qubit coherence with a fast latching readout

Irfan A. Siddiqi, Rajamani Vijay, Michael Metcalfe +4 more

The ``quantronium'' is a superconducting qubit consisting of a split Cooper pair box in which a large tunnel junction is inserted. This circuit has a special bias point where the Larmor frequency is, to first order, insensitive to fluctuations in the bias parameters---the charge of the box island and the phase of the large junction. At this optimal working point, the state of the qubit can be determined by dispersive measurements that probe the second derivative of the state energy with respect to these bias parameters. We use the quantronium phase degree of freedom to perform a nonlinear, dispersive measurement of its inductive response using bifurcation amplification. This dispersive readout projects the state of the qubit in a few nanoseconds, and its latching property allows us to record the resulting information in a few hundred nanoseconds. We have measured, using this technique, Rabi oscillations and Ramsey fringes with an improved signal-to-noise ratio and contrast. The speed of this readout scheme also opens the door for a class of experiments that would characterize the relaxation processes associated with the measurement protocol.

arXiv:cond-mat/0507548•Physical Review B•Feb 23, 2006•157 citations

Experiments on a Quantum Gate Based on Charge-Current Superconducting Qubit

Michel Devoret

During this grant, we have invented, designed and successfully operated a new type of readout for charge-phase superconducting qubits. This new readout is based on the bifurcation of an RF-driven Josephson junction inserted in the loop of a split Cooper pair box. When the amplitude of the RF drive is in the vicinity of the bifurcation points a small change in the effective critical current of the junction is amplified into a large phase change in the reflected signal. The performance reached by the device is in agreement with theoretical predictions. The speed of this readout is unprecedented: we measure in 20ns the critical current increment corresponding to the transition between the 2 states of the qubit. The repetition rate is 10Mz. We have performed a series of experiments showing that the amplification mechanism behaves as expected. No quasiparticles are produced during the readout and the back-action on the qubit when the readout is OFF is minimal. We have performed decoherence measurements at dilution refrigerator temperatures on the quantronium qubit integrated with RF readout. These measurements involve all possible 1-qubit gate operations. Compared with the DC readout method we have gained in repetition rate (factor of 100), signal-to-noise ration on all coherence signals (factor of 10) but most importantly, on readout fidelity which now attains more than 60% (compared to 15%). This last improvement is very important for showing the entanglement produced by two-bit gate operations. The T1 has also been improved by 250%. We still have comparable T2 as before but we suspect this is due to insufficient filtering on the listening lines of our measurement apparatus and this problem is technically solvable. In parallel with this work on readout and decoherence of the quantronium qubit, we have designed a new 2-bit gate based on capacitive coupling between qubits and worked out the complete protocol of pulses.

•Aug 31, 2005•0 citations

RF-Driven Josephson Bifurcation Amplifier for Quantum Measurement

Irfan A. Siddiqi, Rajamani Vijay, F. Pierre +5 more

We have constructed a new type of amplifier whose primary purpose is the readout of superconducting quantum bits. It is based on the transition of a rf-driven Josephson junction between two distinct oscillation states near a dynamical bifurcation point. The main advantages of this new amplifier are speed, high sensitivity, low backaction, and the absence of on-chip dissipation. Pulsed microwave reflection measurements on nanofabricated Al junctions show that actual devices attain the performance predicted by theory.

arXiv:cond-mat/0312623•Physical Review Letters•Nov 10, 2004•378 citations

Towards quantum-noise limited multiplexed microwave readout of qubits

Kevin P. O’Brien, Chris Macklin, David J. Hover +5 more

Coherent circuits based on superconducting elements hold tremendous promise for the practical implementation of quantum information technology: advanced computation, cryptography, and hardware simulation of complex materials systems are envisioned applications. Such circuits are essentially engineered atoms with level transitions in the 4-8 GHz regime; as such “read” and “write” operations are performed with the aid of fast microwave pulses and low-noise amplifiers, respectively. Recent advances in cavity-based superconducting parametric amplifiers have enabled real-time measurement and feedback in one and two qubits. We demonstrate a novel Josephson junction transmission-line based traveling-wave amplifier which employs sub-wavelength phase matching resonators to achieve high gain, several GHz of bandwidth, and near quantum-noise limited performance. Such devices will enable multiplexed qubit readout in integrated architectures comprised of a variety of microwave frequency analog and digital superconducting technologies: signal sources, multiplexers, ADCs, DACs, mixers, and amplifiers.

IEEE MTT-S International Microwave Symposium digest•May 1, 2016•2 citations

Resonant readout of a superconducting persistent current qubit

Janice C. Lee

Superconducting Josephson junction devices rank among the best candidates for realizing a quantum computer. While the coherent control of quantum dynamics has been demonstrated in these solid-state, macroscopic quantum systems, a major challenge has been to increase the coherence times for these qubits. With an objective to reduce the level of readout-induced decoherence, this thesis work focuses on a resonant readout scheme developed for a niobium persistent-current (PC) qubit. This non-dissipative readout approach detects the flux state of the qubit by sensing a change in the Josephson inductance of a SQUID magnetometer. By incorporating the SQUID inductor in a high-Q resonant circuit, we distinguished the flux states of the qubit as a shift in the resonant frequency at 300 mK. The nonlinearity due to the Josephson inductance has characteristic effects on the resonant behavior of the readout circuit. We observed novel manifestation of this nonlinearity given the high quality factor of the resonance. The readout circuit was characterized in the linear as well as the nonlinear regime for its potential use as a bifurcation amplifier. Numerical simulations based on Josephson-junction circuits were also performed to understand the observed nonlinearity in the resonant behavior.

•Jan 1, 2006•0 citations

Multiplexed readout of transmon qubits with Josephson bifurcation amplifiers

Vivien Schmitt, Xin Zhou, Kristinn Júlíusson +5 more

Achieving individual qubit readout is a major challenge in the development of scalable superconducting quantum processors. We have implemented the multiplexed readout of a four transmon qubit circuit using nonlinear resonators operated as Josephson bifurcation amplifiers. We demonstrate the simultaneous measurement of Rabi oscillations of the four transmons. We find that multiplexed Josephson bifurcation is a high-fidelity readout method, the scalability of which is not limited by the need of a large-bandwidth, nearly quantum-limited amplifier as is the case with linear readout resonators.

arXiv:1409.5647•Physical Review A•Dec 22, 2014•38 citations
Dispersive readouts for superconducting qubits have the advantage of speed and minimal invasiveness. We have developed such an amplifier, the cavity bifurcation amplifier (CBA), and applied it to the readout of the quantronium qubit. It consists of a Josephson junction embedded in a microwave on-chip resonator. In contrast with the Josephson bifurcation amplifier, which has an on-chip capacitor shunting a junction, the resonator is based on a simple coplanar waveguide imposing a predetermined frequency and whose other rf characteristics such as the quality factor are easily controlled and optimized. Under proper microwave irradiation conditions, the CBA has two metastable states. Which state is adopted by the CBA depends on the state of a quantronium qubit coupled to the CBA's junction. Due to the megahertz repetition rate and large signal to noise ratio, we can show directly that the coherence is limited by 1∕f1∕f1∕f gate charge noise when biased at the ``sweet spot''---a point insensitive to first order gate charge fluctuations. This architecture lends itself to scalable quantum computing using a multiresonator chip with multiplexed readouts.
The ``quantronium'' is a superconducting qubit consisting of a split Cooper pair box in which a large tunnel junction is inserted. This circuit has a special bias point where the Larmor frequency is, to first order, insensitive to fluctuations in the bias parameters---the charge of the box island and the phase of the large junction. At this optimal working point, the state of the qubit can be determined by dispersive measurements that probe the second derivative of the state energy with respect to these bias parameters. We use the quantronium phase degree of freedom to perform a nonlinear, dispersive measurement of its inductive response using bifurcation amplification. This dispersive readout projects the state of the qubit in a few nanoseconds, and its latching property allows us to record the resulting information in a few hundred nanoseconds. We have measured, using this technique, Rabi oscillations and Ramsey fringes with an improved signal-to-noise ratio and contrast. The speed of this readout scheme also opens the door for a class of experiments that would characterize the relaxation processes associated with the measurement protocol.
During this grant, we have invented, designed and successfully operated a new type of readout for charge-phase superconducting qubits. This new readout is based on the bifurcation of an RF-driven Josephson junction inserted in the loop of a split Cooper pair box. When the amplitude of the RF drive is in the vicinity of the bifurcation points a small change in the effective critical current of the junction is amplified into a large phase change in the reflected signal. The performance reached by the device is in agreement with theoretical predictions. The speed of this readout is unprecedented: we measure in 20ns the critical current increment corresponding to the transition between the 2 states of the qubit. The repetition rate is 10Mz. We have performed a series of experiments showing that the amplification mechanism behaves as expected. No quasiparticles are produced during the readout and the back-action on the qubit when the readout is OFF is minimal. We have performed decoherence measurements at dilution refrigerator temperatures on the quantronium qubit integrated with RF readout. These measurements involve all possible 1-qubit gate operations. Compared with the DC readout method we have gained in repetition rate (factor of 100), signal-to-noise ration on all coherence signals (factor of 10) but most importantly, on readout fidelity which now attains more than 60% (compared to 15%). This last improvement is very important for showing the entanglement produced by two-bit gate operations. The T1 has also been improved by 250%. We still have comparable T2 as before but we suspect this is due to insufficient filtering on the listening lines of our measurement apparatus and this problem is technically solvable. In parallel with this work on readout and decoherence of the quantronium qubit, we have designed a new 2-bit gate based on capacitive coupling between qubits and worked out the complete protocol of pulses.
We have constructed a new type of amplifier whose primary purpose is the readout of superconducting quantum bits. It is based on the transition of a rf-driven Josephson junction between two distinct oscillation states near a dynamical bifurcation point. The main advantages of this new amplifier are speed, high sensitivity, low backaction, and the absence of on-chip dissipation. Pulsed microwave reflection measurements on nanofabricated Al junctions show that actual devices attain the performance predicted by theory.
Coherent circuits based on superconducting elements hold tremendous promise for the practical implementation of quantum information technology: advanced computation, cryptography, and hardware simulation of complex materials systems are envisioned applications. Such circuits are essentially engineered atoms with level transitions in the 4-8 GHz regime; as such “read” and “write” operations are performed with the aid of fast microwave pulses and low-noise amplifiers, respectively. Recent advances in cavity-based superconducting parametric amplifiers have enabled real-time measurement and feedback in one and two qubits. We demonstrate a novel Josephson junction transmission-line based traveling-wave amplifier which employs sub-wavelength phase matching resonators to achieve high gain, several GHz of bandwidth, and near quantum-noise limited performance. Such devices will enable multiplexed qubit readout in integrated architectures comprised of a variety of microwave frequency analog and digital superconducting technologies: signal sources, multiplexers, ADCs, DACs, mixers, and amplifiers.
Superconducting Josephson junction devices rank among the best candidates for realizing a quantum computer. While the coherent control of quantum dynamics has been demonstrated in these solid-state, macroscopic quantum systems, a major challenge has been to increase the coherence times for these qubits. With an objective to reduce the level of readout-induced decoherence, this thesis work focuses on a resonant readout scheme developed for a niobium persistent-current (PC) qubit. This non-dissipative readout approach detects the flux state of the qubit by sensing a change in the Josephson inductance of a SQUID magnetometer. By incorporating the SQUID inductor in a high-Q resonant circuit, we distinguished the flux states of the qubit as a shift in the resonant frequency at 300 mK. The nonlinearity due to the Josephson inductance has characteristic effects on the resonant behavior of the readout circuit. We observed novel manifestation of this nonlinearity given the high quality factor of the resonance. The readout circuit was characterized in the linear as well as the nonlinear regime for its potential use as a bifurcation amplifier. Numerical simulations based on Josephson-junction circuits were also performed to understand the observed nonlinearity in the resonant behavior.
Achieving individual qubit readout is a major challenge in the development of scalable superconducting quantum processors. We have implemented the multiplexed readout of a four transmon qubit circuit using nonlinear resonators operated as Josephson bifurcation amplifiers. We demonstrate the simultaneous measurement of Rabi oscillations of the four transmons. We find that multiplexed Josephson bifurcation is a high-fidelity readout method, the scalability of which is not limited by the need of a large-bandwidth, nearly quantum-limited amplifier as is the case with linear readout resonators.