Existing schemes for semiconductor spin qubit readout involve either spin-to-charge conversion or electric dipole coupling to a superconducting resonator. The former requires destructive readout while the latter suffers from enhanced qubit dephasing, limiting the potential performance of quantum measurement: an open challenge in semiconductor quantum computing. Here we propose a coupling to a superconducting resonator based on qubit energy curvature versus gate voltage, which enables quantum nondemolition (QND) readout while the qubit resides in its full sweet spot and with zero dipole coupling (offering resilience to charge noise). Readout strengths of tens to hundred megahertz (MHz) can be reached, at least ten times larger than in the previously proposed schemes. We show how this curvature interaction generates two strictly QND readout approaches: (i) via a ``dispersive-like'' (quantum capacitance) spin-dependent resonator energy shift, similar in implementation to circuit-QED dispersive readout, but avoiding the Purcell effect; and (ii) with the addition of qubit gate voltage modulation, a longitudinal readout which can be selectively switched on, for a chosen n-qubit subsystem. Neither scheme requires the qubit and resonator to be close in frequency.
Existing schemes for semiconductor spin qubit readout involve either spin-to-charge conversion or electric dipole coupling to a superconducting resonator. The former requires destructive readout while the latter suffers from enhanced qubit dephasing, limiting the potential performance of quantum measurement: an open challenge in semiconductor quantum computing. Here we propose a coupling to a superconducting resonator based on qubit energy curvature versus gate voltage, which enables quantum nondemolition (QND) readout while the qubit resides in its full sweet spot and with zero dipole coupling (offering resilience to charge noise). Readout strengths of tens to hundred megahertz (MHz) can be reached, at least ten times larger than in the previously proposed schemes. We show how this curvature interaction generates two strictly QND readout approaches: (i) via a ``dispersive-like'' (quantum capacitance) spin-dependent resonator energy shift, similar in implementation to circuit-QED dispersive readout, but avoiding the Purcell effect; and (ii) with the addition of qubit gate voltage modulation, a longitudinal readout which can be selectively switched on, for a chosen n-qubit subsystem. Neither scheme requires the qubit and resonator to be close in frequency.
We propose entangling operations based on the energy curvature couplings of encoded spin qubits to a superconducting cavity, exploring the nonlinear qubit response to a gate voltage variation. For a two-qubit (n-qubit) entangling gate we explore acquired geometric phases via a time-modulated longitudinal ${\ensuremath{\sigma}}_{z}$ coupling, offering gate times of tens of nanoseconds even when the qubits and the cavity are far detuned. No dipole moment is necessary: the qubit transverse ${\ensuremath{\sigma}}_{x}$ coupling to the resonator is zero at the full sweet spot of the encoded spin qubit of interest (a triple quantum dot three-electron exchange-only qubit or a double quantum dot singlet-triplet qubit). This approach allows always-on, exchange-only qubits, for example, to stay on their ``sweet spots'' during gate operations, minimizing the charge noise and eliminating an always-on static longitudinal qubit-qubit coupling. We calculate the main gate errors due to the (1) diffusion (Johnson) noise and (2) damping of the resonator, the (3) 1/f-charge noise qubit gate dephasing and 1/f noise on the longitudinal coupling, (4) qubit dephasing and AC-Stark frequency shifts via photon fluctuations in the resonator, and (5) spin-dependent resonator frequency shifts (via a ``dispersivelike'' static curvature coupling), most of them associated with the nonzero qubit energy curvature (quantum capacitance). Using spin-echo-like error suppression at optimal regimes, gate infidelities of ${10}^{\ensuremath{-}2}--{10}^{\ensuremath{-}3}$ can be achieved with experimentally existing parameters. The proposed schemes seem suitable for remote spin-to-spin entanglement of two spin qubits or a cluster of spin qubits: an important resource of quantum computing.
Strong coupling of semiconductor spin qubits to superconducting microwave resonators was recently demonstrated [X. Mi et al., Nature 555, 599 (2018); A. J. Landig et al., Nature 560, 179 (2018); N. Samkharadze et al., Science 359, 1123 (2018); T. Cubaynes et al., NPJ Quant. Inf. 5, 47 (2019)]. These breakthroughs pave the way for quantum information processing that combines the long coherence times of solid-state spin qubits with the long-distance connectivity, fast control, and fast high-fidelity quantum-non-demolition readout of existing superconducting qubit implementations. Here we theoretically analyze and optimize the dispersive readout of a single spin in a semiconductor double quantum dot (DQD) coupled to a microwave resonator via its electric dipole moment. The strong spin-photon coupling arises from the motion of the electron spin in a local magnetic field gradient. We calculate the signal-to-noise ratio (SNR) of the readout accounting for both Purcell spin relaxation and spin relaxation arising from intrinsic electric noise within the semiconductor. We express the maximum achievable SNR in terms of the cooperativity associated with these two dissipation processes. We find that while the cooperativity increases with the strength of the dipole coupling between the DQD and the resonator, it does not depend on the strength of the magnetic field gradient. We then optimize the SNR as a function of experimentally tunable DQD parameters. We identify wide regions of parameter space where the unwanted backaction of the resonator photons on the qubit is small. Moreover, we find that the coupling of the resonator to other DQD transitions can enhance the SNR by at least a factor of two, a ``straddling'' effect [J. Koch et al., Phys. Rev. A 76, 042319 (2007)] that occurs only at nonzero energy detuning of the DQD double-well potential. We estimate that with current technology, single-shot readout fidelities in the range 82--95% can be achieved within a few $\ensuremath{\mu}\mathrm{s}$ of readout time without requiring the use of Purcell filters.
Dispersive readout, the current standard for measuring superconducting qubits, relies on relatively easy to engineer, static transverse coupling between a qubit and a detuned cavity mode. However, this method requires circuit design trade-offs between qubit-cavity coupling, cavity-feedline coupling, detuning, and the resultant decoherence introduced by the cavity mode. Additionally, the criteria for performing quantum nondemolition measurements, including reduced cavity photon numbers, further limits speed and fidelity. In this work, we introduce a circuit with pulse-tunable qubit-cavity and cavity-feedline couplings so that the entire qubit-measurement process can be fully optimized. Here, the core measurement process resembles a quantum gate operation between the qubit and the cavity, with the cavity acting like an ancilla, storing the qubit-state information. To fully explore time-dependent effects of the full qubit-cavity dynamics, we go beyond the rotating-wave, Jaynes-Cummings, or dispersive approximations, to develop a pulsed-measurement protocol. In addition, we propose a realistic circuit architecture that can provide a very fast, high-fidelity, QND measurement with near-unit efficiency.
Quantum technologies, including those based on superconducting quantum circuits, require high-fidelity high-speed detection of the quantum state of a qubit. Standard quantum nondemolition readout of a superconducting qubit is based on its dispersive coupling to a resonator, but this method suffers from the Purcell effects: Purcell decay, critical photon number, and qubit-dependent Kerr nonlinearity. The authors propose a method in which both speed and fidelity of flux-qubit readout can avoid all three Purcell limitations.
Spin qubits in gate-defined semiconductor quantum dots are a promising platform for realising a scalable quantum computer. This platform encodes quantum information into the intrinsic angular momentum (spin) of individual electrons or holes. In particular, hole spins in quantum dots enable the possibility of all-electrical spin control due to their intrinsic spin-orbit coupling. One important criterion of a quantum computer is the ability to reliably read out the state of the qubit. This is done by mapping spin information to the charge degree of freedom, combined with a method for charge detection. Charge detection can be facilitated by coupling a resonator directly to the quantum dot gate or to a charge sensor and measuring the resonator's phase or amplitude response. In this thesis, we describe a set of experiments relating to the implementation of hole spin qubit readout with superconducting resonators. First, we study gate-based charge sensing in a Si fin field-effect transistor (finFET) device using a superconducting NbN nanowire resonator. We find that the resonator amplifies capacitive crosstalk when electrical control pulses are applied to gate electrodes in this device. This occurs whenever a spectral component of qubit control pulses overlaps with the resonance frequency, which we show may occur for both baseband and radio-frequency (RF) drive signals. We quantify this crosstalk in a transport-based method, and attribute its source to the capacitance between the bondpads of neighbouring gate electrodes. In a second experiment, we use an RF charge sensor with the same nanowire technology to read out hole spin qubits formed in the quantum well of a Ge/SiGe heterostructure. A screening layer approach is used to facilitate RF matching due to large RF dissipation found in the heterostructure. We implement a double-latched readout scheme in this system to reduce errors arising from both spin and charge decay during readout. The spin-to-charge conversion process and its dependence on magnetic field orientation is studied. Spin and charge decay processes arising after spin-to-charge conversion are mitigated by choosing an optimal working point for the field orientation, field amplitude and readout pulse times. By doing so, we achieve an average single-shot state-preparation-and-measurement fidelity of 97%, primarily bounded by imperfect state preparation and limited signal-to-noise ratio. Finally, we study coplanar waveguide resonators fabricated from NbN. We investigate the feasibility of integrating this type of resonator onto the same chip as the Si finFET quantum dots. We then develop a novel resonator readout technique by the interference of two microwave sidebands. We demonstrate the insensitivity of this technique to common-mode phase and amplitude noise both theoretically and experimentally. This technique is then used to study resonator noise arising from two-level system defects. These results highlight both the practical constraints and the potential for achieving high readout fidelities using resonator-based hole spin qubit readout. This work establishes a blueprint for mitigating resonator-induced crosstalk and enabling high-fidelity readout in lossy materials by incorporating a screening layer.
The need for fast readout to measure the state of a quantum dot device has important applications in the capabilities of using them as a means for quantum information processing. Traditional charge sensors used to readout the charge state of a quantum dot device are very robust and sensitive electrometers that have been in use since the late 1980s. They pose an issue to the future of quantum dots as a viable means of quantum computing, and that is in their slow acquisition times of the charge state of the quantum dot. This rate of measurement means that implementing any quantum error correction scheme becomes very difficult or even unfeasible as the coherence times of these semiconductor systems is short compared to charge sensor’s acquisition times. A possibility to speed up the measurement process of the charge state is possible thanks to the atomic molecular and optical (AMO) physics community.Cavity quantum electrodynamics (CQED) is the study of light-matter interactions when both the light and matter are taken to be quantized. A photon may interact with an atom via a dipole interaction to excite it from its ground state to its excited state, and the reverse can occur where the atom emits a photon and decays from its excited state ii to the ground state. This fundamental interaction which has been extensively studied in the AMO community since the early 1960s had been adopted by the superconducting qubit community to measure the state of their qubits. These superconducting qubits, representing atoms, which are coupled to a resonant structure on chip, which represents the photons that can interact with the artificial atom. Since these systems were not traditional trapped or neutral atoms interacting with a photon via a laser, but instead planar circuit structures, the superconducting qubit community re-coined the term cavity quantum electrodynamics to circuit quantum electrodynamics, which we will refer to as cQED.The quantum dot community adapted these methods of what is known as dispersive readout; a capacitive change of the atomic like system, results in a dispersive shift which then alters the characteristic frequency response of the resonant structure. This has allowed for a new kind of charge sensor by means of measuring the resonators response due to its coupling to a quantum dot system. This can be done with very high frequency microwave circuitry, allowing much faster readout than is capable via traditional charge sensors. Thus, allowing a pathway to implement quantum error correction schemes with reasonable times compared to any dephasing or decoherence times of the semiconductor system. Furthermore, such fast readout allows for feedback protocols to be implemented to the system to correct for certain undesirable effects due to instruments or the system itself. Our work focuses on a limit of this cQED interaction of the quantum dots to a resonant structure allowing us to do fast readout of the quantum dot charge states via a dispersive shift.The work I will demonstrate in this dissertation will be in the efforts of fast readout on the charge occupation of a double quantum dot system which is galvanically coupled to a superconducting microwave resonator. This was done in a Si/SiGe heterostructure system where I designed, simulated, and fabricated the device which was optimized to have a stronger dispersive shift signal due to an enhanced gate lever arm that couples to the resonator. I will discuss our results of attaining a minimum integration time of 34.54 ns for a unity signal to noise ratio. This demonstrates a fast readout system in the community iii which could be extended to allow for even better readout speeds with faster instruments than what were available to me for the experiment. I will further discuss our characterization of the hybrid system and how we extracted a charge noise due to charging events between the two dots in our system up to around 10 kHz. This work demonstrates a robust dispersive readout scheme which helps in the scalability of hybrid superconducting-semiconducting architectures for means of quantum information processing.