Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1609.09694 · IEEE Transactions on Applied Superconductivity

AlN-Buffered Superconducting NbN Nanowire Single-Photon Detector on GaAs

Ekkehart Schmidt, K. Ilin, M. Siegel

Published Dec 19, 2016• 24 citations
arXivHTMLPDF

Abstract

We investigated the suitability of AlN as a buffer layer for NbN superconducting nanowire single-photon detectors (SNSPDs) on GaAs. The NbN films with a thickness of 3.3-20 nm deposited onto GaAs substrates with an AlN buffer layer demonstrate a higher critical temperature, critical current density, and lower residual resistivity in comparison to films deposited onto bare substrates. Unfortunately, the thermal coupling of the NbN film to the substrate weakens. SNSPDs made of 4.9-nm-thick NbN films on buffered substrates (in comparison to detectors made from NbN films on bare GaAs) demonstrate three orders of magnitude lower dark count rates and about ten times higher detection efficiency at 900 nm being measured at 90% of the critical current. The system timing jitter of SNSPDs on buffered substrates is 72 ps, which is 36 ps lower than those on bare substrate. However, a weaker thermal coupling of NbN nanowire to the buffered substrate leads to a latching effect at bias currents > 0.97 IC.

DOI
10.1109/tasc.2016.2637358

Related papers

Nb5N6 Buffered Superconducting NbN Nanowire Single-Photon Detector on Si Substrate

Tao Xu, Xiaoqing Jia, Shi Chen +8 more

Superconducting nanowire single photon detectors (SNSPDs) based on Si substrates have demonstrated excellent performance, such as high efficiency, low dark count rate, short reset time and low timing jitter. But due to the lattice mismatch between NbN and Si substrate, the performance of film is limited. To this end, Nb5N6layer is fabricated as the buffer layer between the NbN film and Si substrate, and that will reduce the mismatch and optimize superconducting properties of NbN films. The 6nm-thick film with a 65 nm-thick buffer layer shows the zero resistance critical temperature (Tc0) of 13.27 K, which is 5 K higher than that without buffer. Based on the NbN film on the buffered substrate, we fabricated SNSPD devices demonstrate critical current (IC) of 65 μA which is 5 ~ 6 times higher to the detectors without buffer. Besides, the experiment results prove that the buffer layer reduces the kinetic inductance, which fasten the recovery of nanowire.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2019•1 citation

NbN-on-Si superconducting nanowire single photon detectors: effect of a sputtered AlN buffer layer

Raouia Rhazi, H. Machhadani, Catherine Bougerol +8 more

Superconducting nanowire single photon detectors stand today as the best technology, due to their near-unity detection efficiency, low dark count rates, and low timing jitter. In this work, we demonstrate the improvement of the superconducting properties of NbN thin films on 8” silicon-on-insulator wafers by using an ultra-thin (10-15 nm) sputtered AlN buffer layer. The higher crystalline quality of NbN, leads to an increase of the superconducting critical temperature up to 10 K for 9-nm-thick NbN films. The material was validated for single photon detection using a fiber-coupled vertical SNSPD with half-cavity architecture. This results opens the way for the development of CMOS compatible waveguide-integrated detectors. The implementation of such guided devices is a keystone for the development of a fully integrated quantum photonics platform able to generate, manipulate and detect a large number of photonic qubits for secure communications and quantum computing applications.

Advanced Photon Counting Techniques•Apr 8, 2021•0 citations

Effect of buffer layer on thermal recovery of superconducting nanowire single-photon detector

T Xu, S. Chen, Hongkai Shi +7 more

Abstract Superconducting nanowire single-photon detectors (SNSPDs) wherein ultrathin films are fabricated on Si substrates are greatly affected by lattice mismatch between the thin film and the substrate. A buffer layer can be used to reduce such lattice mismatch or optimize the strain in the film, thereby improving device performance. We prepared and optimized Nb 5 N 6 as a buffer layer and found that it considerably improved the properties of NbN films on Si substrates. The zero-resistance critical temperature ( T C0 ) of a 3 nm thick NbN film with a 20 nm thick buffer layer was 10.3 K. SNSPDs with Nb 5 N 6 -buffered NbN films were fabricated and compared with normal devices; the fabricated devices had high hysteresis current and low timing jitter. Furthermore, we investigated the thermal diffusion process of the device based on the hysteresis current and hotspot relaxation time and found that Nb 5 N 6 buffer layers enhance the thermal coupling between the superconducting film and substrates. The relaxation time of buffered SNSPD was 14.2 ps, which was shorter than that of nonbuffered SNSPD by 17.8 ps. These effects explain the performance improvement observed in the case of the buffered devices.

Superconductor Science and Technology•May 11, 2021•12 citations

Comparison of Superconducting Nanowire Single-Photon Detectors Made of NbTiN and NbN Thin Films

Xiaoyan Yang, Lixing You, Lu Zhang +5 more

We fabricated superconducting nanowire single-photon detectors (SNSPDs) made of NbTiN and NbN thin films in the same fabrication batch. Various parameters, such as critical temperature, resistivity, switching current, and kinetic inductance, were compared between the two types of SNSPDs. These data indicate that NbTiN SNSPD surpasses NbN SNSPD in many aspects, including a shorter recovery time due to smaller kinetic inductance, a lower timing jitter due to higher switching current, and better uniformity. Based on the measurement of 28 out of 121 NbTiN SNSPDs on a 2-in Si wafer, 71% of detectors show a system detection efficiency of over 50% at a dark count rate of 100 Hz, with the maximum efficiency being 77.5%.

IEEE Transactions on Applied Superconductivity•Nov 22, 2017•45 citations

Nanowire single-photon detectors made of atomic layer-deposited niobium nitride

E Knehr, A Kuzmin, D Yu Vodolazov +6 more

Abstract We demonstrate and characterize superconducting nanowire single-photon detectors made from atomic layer-deposited (ALD) NbN layers. To assess the suitability of these films as a detector material, transport properties of bare films and bridges of different dimensions and thicknesses are investigated. Similar ratios of the measured critical current to the depairing current are obtained for micro-bridges made from ALD and sputtered NbN films. Furthermore, we characterized the single-photon response for 5 and 10 nm thick nanowire detectors. A 100 nm wide straight nanowire with a length of 5 μ m exhibits saturated count rate dependencies on bias current and a cut-off wavelength in the near-infrared range. The ALD technique could open up the possibility to fabricate NbN-based detectors on the wafer scale and to conformally cover also non-planar surfaces for novel device concepts.

arXiv:1906.05214•Superconductor Science and Technology•Sep 27, 2019•27 citations

Optimisation of NbN thin films on GaAs substrates for in-situ single photon detection in structured photonic devices

G. Reithmaier, J. Senf, S. Lichtmannecker +5 more

We prepare NbN thin films by DC magnetron sputtering on [100] GaAs substrates, optimise their quality, and demonstrate their use for efficient single photon detection in the near-infrared. The interrelation between the Nb:N content, growth temperature, and crystal quality is established for 4–22 nm thick films. Optimised films exhibit a superconducting critical temperature of 12.6 ± 0.2K for a film thickness of 22 ± 0.5 nm and 10.2 ± 0.2 K for 4 ± 0.5 nm thick films that are suitable for single photon detection. The optimum growth temperature is shown to be ∼475 °C reflecting a trade-off between enhanced surface diffusion, which improves the crystal quality, and arsenic evaporation from the GaAs substrate. Analysis of the elemental composition of the films provides strong evidence that the δ-phase of NbN is formed in optimised samples, controlled primarily via the nitrogen partial pressure during growth. By patterning optimum 4 nm and 22 nm thick films into a 100 nm wide, 369μm long nanowire meander using electron beam lithography and reactive ion etching, we fabricated single photon detectors on GaAs substrates. Time-resolved studies of the photo-response, absolute detection efficiency, and dark count rates of these detectors as a function of the bias current reveal maximum single photon detection efficiencies as high as 21 ± 2% at 4.3 ± 0.1 K with ∼50 k dark counts per second for bias currents of 98%IC at a wavelength of 950 nm. As expected, similar detectors fabricated from 22 nm thick films exhibit much lower efficiencies (0.004%) with very low dark count rates ≤3 cps. The maximum lateral extension of a photo-generated resistive region is estimated to be 30 ± 8 nm, clearly identifying the low detection efficiency and dark count rate of the thick film detectors as arising from hotspot cooling via the heat reservoir provided by the NbN film.

arXiv:1212.2038•Journal of Applied Physics•Apr 10, 2013•26 citations
We investigated the suitability of AlN as a buffer layer for NbN superconducting nanowire single-photon detectors (SNSPDs) on GaAs. The NbN films with a thickness of 3.3-20 nm deposited onto GaAs substrates with an AlN buffer layer demonstrate a higher critical temperature, critical current density, and lower residual resistivity in comparison to films deposited onto bare substrates. Unfortunately, the thermal coupling of the NbN film to the substrate weakens. SNSPDs made of 4.9-nm-thick NbN films on buffered substrates (in comparison to detectors made from NbN films on bare GaAs) demonstrate three orders of magnitude lower dark count rates and about ten times higher detection efficiency at 900 nm being measured at 90% of the critical current. The system timing jitter of SNSPDs on buffered substrates is 72 ps, which is 36 ps lower than those on bare substrate. However, a weaker thermal coupling of NbN nanowire to the buffered substrate leads to a latching effect at bias currents > 0.97 IC.
Superconducting nanowire single photon detectors (SNSPDs) based on Si substrates have demonstrated excellent performance, such as high efficiency, low dark count rate, short reset time and low timing jitter. But due to the lattice mismatch between NbN and Si substrate, the performance of film is limited. To this end, Nb5N6layer is fabricated as the buffer layer between the NbN film and Si substrate, and that will reduce the mismatch and optimize superconducting properties of NbN films. The 6nm-thick film with a 65 nm-thick buffer layer shows the zero resistance critical temperature (Tc0) of 13.27 K, which is 5 K higher than that without buffer. Based on the NbN film on the buffered substrate, we fabricated SNSPD devices demonstrate critical current (IC) of 65 μA which is 5 ~ 6 times higher to the detectors without buffer. Besides, the experiment results prove that the buffer layer reduces the kinetic inductance, which fasten the recovery of nanowire.
Superconducting nanowire single photon detectors stand today as the best technology, due to their near-unity detection efficiency, low dark count rates, and low timing jitter. In this work, we demonstrate the improvement of the superconducting properties of NbN thin films on 8” silicon-on-insulator wafers by using an ultra-thin (10-15 nm) sputtered AlN buffer layer. The higher crystalline quality of NbN, leads to an increase of the superconducting critical temperature up to 10 K for 9-nm-thick NbN films. The material was validated for single photon detection using a fiber-coupled vertical SNSPD with half-cavity architecture. This results opens the way for the development of CMOS compatible waveguide-integrated detectors. The implementation of such guided devices is a keystone for the development of a fully integrated quantum photonics platform able to generate, manipulate and detect a large number of photonic qubits for secure communications and quantum computing applications.
Abstract Superconducting nanowire single-photon detectors (SNSPDs) wherein ultrathin films are fabricated on Si substrates are greatly affected by lattice mismatch between the thin film and the substrate. A buffer layer can be used to reduce such lattice mismatch or optimize the strain in the film, thereby improving device performance. We prepared and optimized Nb 5 N 6 as a buffer layer and found that it considerably improved the properties of NbN films on Si substrates. The zero-resistance critical temperature ( T C0 ) of a 3 nm thick NbN film with a 20 nm thick buffer layer was 10.3 K. SNSPDs with Nb 5 N 6 -buffered NbN films were fabricated and compared with normal devices; the fabricated devices had high hysteresis current and low timing jitter. Furthermore, we investigated the thermal diffusion process of the device based on the hysteresis current and hotspot relaxation time and found that Nb 5 N 6 buffer layers enhance the thermal coupling between the superconducting film and substrates. The relaxation time of buffered SNSPD was 14.2 ps, which was shorter than that of nonbuffered SNSPD by 17.8 ps. These effects explain the performance improvement observed in the case of the buffered devices.
We fabricated superconducting nanowire single-photon detectors (SNSPDs) made of NbTiN and NbN thin films in the same fabrication batch. Various parameters, such as critical temperature, resistivity, switching current, and kinetic inductance, were compared between the two types of SNSPDs. These data indicate that NbTiN SNSPD surpasses NbN SNSPD in many aspects, including a shorter recovery time due to smaller kinetic inductance, a lower timing jitter due to higher switching current, and better uniformity. Based on the measurement of 28 out of 121 NbTiN SNSPDs on a 2-in Si wafer, 71% of detectors show a system detection efficiency of over 50% at a dark count rate of 100 Hz, with the maximum efficiency being 77.5%.
Abstract We demonstrate and characterize superconducting nanowire single-photon detectors made from atomic layer-deposited (ALD) NbN layers. To assess the suitability of these films as a detector material, transport properties of bare films and bridges of different dimensions and thicknesses are investigated. Similar ratios of the measured critical current to the depairing current are obtained for micro-bridges made from ALD and sputtered NbN films. Furthermore, we characterized the single-photon response for 5 and 10 nm thick nanowire detectors. A 100 nm wide straight nanowire with a length of 5 μ m exhibits saturated count rate dependencies on bias current and a cut-off wavelength in the near-infrared range. The ALD technique could open up the possibility to fabricate NbN-based detectors on the wafer scale and to conformally cover also non-planar surfaces for novel device concepts.
We prepare NbN thin films by DC magnetron sputtering on [100] GaAs substrates, optimise their quality, and demonstrate their use for efficient single photon detection in the near-infrared. The interrelation between the Nb:N content, growth temperature, and crystal quality is established for 4–22 nm thick films. Optimised films exhibit a superconducting critical temperature of 12.6 ± 0.2K for a film thickness of 22 ± 0.5 nm and 10.2 ± 0.2 K for 4 ± 0.5 nm thick films that are suitable for single photon detection. The optimum growth temperature is shown to be ∼475 °C reflecting a trade-off between enhanced surface diffusion, which improves the crystal quality, and arsenic evaporation from the GaAs substrate. Analysis of the elemental composition of the films provides strong evidence that the δ-phase of NbN is formed in optimised samples, controlled primarily via the nitrogen partial pressure during growth. By patterning optimum 4 nm and 22 nm thick films into a 100 nm wide, 369μm long nanowire meander using electron beam lithography and reactive ion etching, we fabricated single photon detectors on GaAs substrates. Time-resolved studies of the photo-response, absolute detection efficiency, and dark count rates of these detectors as a function of the bias current reveal maximum single photon detection efficiencies as high as 21 ± 2% at 4.3 ± 0.1 K with ∼50 k dark counts per second for bias currents of 98%IC at a wavelength of 950 nm. As expected, similar detectors fabricated from 22 nm thick films exhibit much lower efficiencies (0.004%) with very low dark count rates ≤3 cps. The maximum lateral extension of a photo-generated resistive region is estimated to be 30 ± 8 nm, clearly identifying the low detection efficiency and dark count rate of the thick film detectors as arising from hotspot cooling via the heat reservoir provided by the NbN film.