We describe a micromachining process to allow back-side coupling of an array of single-mode telecommunication fibers to individual superconducting nanowire single photon detectors (SNSPDs). This approach enables a back-illuminated detector structure which separates the optical access and electrical readout on two sides of the chip and thus allows for compact integration of multi-channel detectors. As proof of principle, we show the integration of four detectors on the same silicon chip with two different designs and their performances are compared. In the optimized design, the device shows saturated system detection efficiency of 16% while the dark count rate is less than 20 Hz, all achieved without the use of metal reflectors or distributed Bragg reflectors (DBRs). This back-illumination approach also eliminates the cross-talk between different detection channels.
We describe a micromachining process to allow back-side coupling of an array of single-mode telecommunication fibers to individual superconducting nanowire single photon detectors (SNSPDs). This approach enables a back-illuminated detector structure which separates the optical access and electrical readout on two sides of the chip and thus allows for compact integration of multi-channel detectors. As proof of principle, we show the integration of four detectors on the same silicon chip with two different designs and their performances are compared. In the optimized design, the device shows saturated system detection efficiency of 16% while the dark count rate is less than 20 Hz, all achieved without the use of metal reflectors or distributed Bragg reflectors (DBRs). This back-illumination approach also eliminates the cross-talk between different detection channels.
We report a compact, scalable, and high-performance superconducting nanowire single-photon detector (SNSPD) array by using a multichannel optical fiber array-coupled configuration. For single pixels with an active area of 18 µm in diameter and illuminated at the telecom wavelength of 1550 nm, we achieved a pixel yield of 13/16 on one chip, an average system detection efficiency of 69% at a dark count rate of 160 cps, a minimum timing jitter of 74 ps, and a maximum count rate of ∼ 40 M c p s . The optical crosstalk coefficient between adjacent channels is better than − 60 d B . The performance of the fiber array-coupled detectors is comparable with a standalone detector coupled to a single fiber. Our method is promising for the development of scalable, high-performance, and high-yield SNSPDs.
We describe a number of methods that have been pursued to develop superconducting nanowire single-photon detectors (SNSPDs) with attractive overall performance, including three systems that operate with >70% system detection efficiency and high maximum counting rates at wavelengths near 1550 nm. The advantages and tradeoffs of various approaches to efficient optical coupling, electrical readout, and SNSPD design are described and contrasted. Optical interfaces to the detectors have been based on fiber coupling, either directly to the detector or through the substrate, using both single-mode and multimode fibers with different approaches to alignment. Recent advances in electrical interfaces have focused on the challenges of scalability and ensuring stable detector operation at high count rates. Prospects for further advances in these and other methods are also described, which may enable larger arrays and higher-performance SNSPD systems in the future. Finally, the use of some of these techniques to develop fully packaged SNSPD systems will be described and the performance available from these recently developed systems will be reviewed.
We have integrated superconducting nanowire single-photon detectors (SNSPDs) with an optical cavity design for front-side illumination. Our optical cavity design increases the coupling efficiency of light to the nanowire detector and enables straightforward proximity fiber-coupling for a multichannel detector system. Using a confocal optical scanning technique, we measured a significantly enhanced optical absorptance of 73% in comparison with 20% in a typical bare nanowire device at 1550 nm and 3 K. Our method of fabrication of these devices on a silicon wafer and the local optical absorptance measurement are important steps toward developing next-generation SNSPD technology.
Single photon detection advanced rapidly in the last decade. The superconducting nanowire single-photon detector (SNSPD) is an emerging technology, which offers low dark count rates, broadband sensitivity from visible to mid-infrared wavelengths and very high quantum efficiency. All these features are appealing for future emerging applications in remote gas sensing, quantum key distribution and quantum information processing. By enclosing the detector in an optical cavity, tuned to the operating wavelength, the total system detection of the SNSPD is improved. Based on the cavity design, the detector absorption is boosted at the desired experimental wavelength. Devices have been fabricated and tested, in this thesis, with enhanced detection efficiency at near-infrared, infrared and mid-infrared wavelengths. NbTiN detectors fabricated on Ta2O5 / SiO2 distributed Bragg reflectors (DBR) for front-side coupling exhibit a system detection efficiency of ≈ 90% at λ = 940 nm for the best device measured. SNSPDs were also fabricated in NbTiN on metallic mirrors for back-side coupling for 1550 and 2333 nm experimental wavelengths. The first design exhibited a system detection efficiency of ≈ 84.5%, at λ = 1550 nm for the best device measured. The second exhibited low system detection efficiency since the device suffered from unexpectedly high dark count rate mainly due to blackbody radiation at 2.2 K. However, it was possible to measure the timing jitter of this device at 350 mK indicating a FWHM of 84 ps. Another technique to improve the total system detection efficiency of the SNSPD, is by fabricating a hairpin-shaped nanowire atop a single mode waveguide. In this design, photons travel through the waveguide and via evanescent coupling are absorbed in the nanowire. These SNSPD devices have been designed to thread along single mode Si ridge waveguides using a hairpin-shaped nanowire structure, which offers enhanced coupling and absorption efficiency via evanescent coupling. These ultra-thin superconducting MoSi detectors are precisely patterned on top of a single mode Si waveguide (600 nm) with alignment error less than 40 nm. Low temperature electrical and nano-optical characterization was carried out using a two-stage pulse tube (PT) coldhead, using an additional 4He / 3He sorption pump, low vibration characterization of SNSPD devices at 350 mK was carried out. Characterised devices exhibit low dark count rate <5 counts per second and timing jitter of ≈ 83 ps full width half maximum (FWHM) at wavelength (λ) = 1550 nm and at critical current ≈ 30 µA.
In this Letter, we report on a device with which to resolve photon numbers and positions simultaneously, using single-channel readout from superconducting nanowire single-photon detectors (SNSPDs). The nanowires in the SNSPDs are connected in series with parallel resistors for producing response pulses with different amplitudes, whose values obey a distribution of 1:2:4:,..,2n-1. In single-photon detection, a saturated counting rate is obtained at a low dark count rate (<10 cps). Furthermore, we observed 16 output modes corresponding one-to-one with 16 states (15 photon responses + 1 state without photons) in multiphoton mode. This structure not only inherits the advantages of high quantum efficiency and low dark count rate of traditional SNSPD, but also realizes the resolution of photon position and number simultaneously without complicated optical system. Thus, this proposal offers a promising platform for realizing scalable and practical quantum information chips.
Abstract Superconducting nanowire single-photon detectors (SNSPDs) with both high system detection efficiency (SDE) and low dark count rate (DCR) play significant roles in quantum information processes and various applications. The background dark counts of SNSPDs originate from the room temperature blackbody radiation coupled to the device via a fiber. Therefore, a bandpass filter (BPF) operated at low temperature with minimal insert loss is necessary to suppress the background DCR. Herein, a low-loss BPF integrated on a single-mode fiber end-face was designed, fabricated and verified for the low temperature implement. The fiber end-face BPF was featured with a typical passband width about 40 nm in the 1550 nm telecom band and a peak transmittance of over 0.98. SNSPD with high SDE fabricated on a distributed Bragg reflector was coupled to the BPF. The device with such a BPF showed an SDE of 80% at a DCR of 0.5 Hz, measured at 2.1 K. Compared the same device without a BPF, the DCR was reduced by over 13 dB with an SDE decrease of <3%.