We report the observation of efficient and low-noise frequency conversion between two microwave modes, mediated by the motion of a mechanical resonator subjected to radiation pressure. We achieve coherent conversion of more than 10^{12} photons/s with a 95% efficiency and a 14 kHz bandwidth. With less than 10^{-1} photons·s^{-1}·Hz^{-1} of added noise, this optomechanical frequency converter is suitable for quantum state transduction. We show the ability to operate this converter as a tunable beam splitter, with direct applications for photon routing and communication through complex quantum networks.
We report the observation of efficient and low-noise frequency conversion between two microwave modes, mediated by the motion of a mechanical resonator subjected to radiation pressure. We achieve coherent conversion of more than 10^{12} photons/s with a 95% efficiency and a 14 kHz bandwidth. With less than 10^{-1} photons·s^{-1}·Hz^{-1} of added noise, this optomechanical frequency converter is suitable for quantum state transduction. We show the ability to operate this converter as a tunable beam splitter, with direct applications for photon routing and communication through complex quantum networks.
Abstract Microelectromechanical systems and integrated photonics provide the basis for many reliable and compact circuit elements in modern communication systems. Electro-opto-mechanical devices are currently one of the leading approaches to realize ultra-sensitive, low-loss transducers for an emerging quantum information technology. Here we present an on-chip microwave frequency converter based on a planar aluminum on silicon nitride platform that is compatible with slot-mode coupled photonic crystal cavities. We show efficient frequency conversion between two propagating microwave modes mediated by the radiation pressure interaction with a metalized dielectric nanobeam oscillator. We achieve bidirectional coherent conversion with a total device efficiency of up to ∼60%, a dynamic range of 2 × 109 photons/s and an instantaneous bandwidth of up to 1.7 kHz. A high fidelity quantum state transfer would be possible if the drive dependent output noise of currently ∼14 photons s−1 Hz−1 is further reduced. Such a silicon nitride based transducer is in situ reconfigurable and could be used for on-chip classical and quantum signal routing and filtering, both for microwave and hybrid microwave-optical applications.
The successes of superconducting quantum circuits at local manipulation of quantum information and photonics technology at long-distance transmission of the same have spurred interest in the development of quantum transducers for efficient, low-noise, and bidirectional frequency conversion of photons between the microwave and optical domains. We propose to realize such functionality through the coupling of electrical, piezoelectric, and optomechanical resonators. The coupling of the mechanical subsystems enables formation of a resonant mechanical supermode that provides a mechanically mediated, efficient single interface to both the microwave and optical domains. The conversion process is analyzed by applying an equivalent circuit model that relates device-level parameters to overall figures of merit for conversion efficiency $\ensuremath{\eta}$ and added noise N. These can be further enhanced by proper impedance matching of the transducer to an input microwave transmission line. The performance of potential transducers is assessed through finite-element simulations, with a focus on geometries in GaAs, followed by considerations of the AlN, LiNbO3, and AlN-on-Si platforms. We present strategies for maximizing $\ensuremath{\eta}$ and minimizing N, and find that simultaneously achieving $\ensuremath{\eta}>50\mathrm{%}$ and N<0.5 should be possible with current technology. We find that the use of a mechanical supermode for mediating transduction is a key enabler for high-efficiency operation, particularly when paired with an appropriate microwave impedance-matching network. Our comprehensive analysis of the full transduction chain enables us to outline a development path for the realization of high-performance quantum transducers that will constitute a valuable resource for quantum information science.
High-gain amplifiers of electromagnetic signals operating near the quantum limit are crucial for quantum information systems and ultrasensitive quantum measurements.However, the existing techniques have a limited gain-bandwidth product and only operate with weak input signals.Here, we demonstrate a two-port optomechanical scheme for amplification and routing of microwave signals, a system that simultaneously performs high-gain amplification and frequency conversion in the quantum regime.Our amplifier, implemented in a two-cavity microwave optomechanical device, shows 41 dB of gain and has a high dynamic range, handling input signals up to 10 13 photons per second, 3 orders of magnitude more than corresponding Josephson parametric amplifiers.We show that although the active medium, the mechanical resonator, is at a high temperature far from the quantum limit, only 4.6 quanta of noise is added to the input signal.Our method can be readily applied to a wide variety of optomechanical systems, including hybrid optical-microwave systems, creating a universal hub for signals at the quantum level.
Coherent interfaces between optical photons and mechanical excitations provide a promising route towards phonon-state engineering and hybrid quantum information processing. Cavity optomechanical systems enable such interfaces via optomechanically induced transparency (OMIT), allowing coherent mapping between traveling optical fields and localized mechanical modes. However, previous implementations of OMIT conversion protocols were limited to classical input signals with large coherent state photon numbers due to room temperature operation and corresponding thermal mechanical noise. Here, we demonstrate efficient low-noise photon-phonon state transfer close to the single-quantum regime in an optomechanical crystal operated at Millikelvin temperatures. Using weak coherent optical input pulses at the few-photon level, we achieve a record-level photon-phonon conversion efficiency of η=0.76, a mechanical storage lifetime of T1=7.3μs, and a tunable conversion bandwidth exceeding 4.5 MHz. Hanbury Brown-Twiss measurements of the retrieved signal demonstrate the coherent nature of the converted phononic state, evidencing low added thermal noise in the conversion process (nth=9.0). These results establish optomechanical crystals as efficient optical interfaces to GHz mechanical modes and provide a pathway toward deterministic single-quantum-level mechanical state preparation.
Microwave-to-optical transducers facilitate the distributed quantum network by combining the high-speed information-processing abilities of superconducting circuits with the long-distance, low-loss transmitting capabilities of optical photons. Besides core metrics such as high efficiency, low noise, and wide bandwidth, practical and scalable transducers also demand a compact footprint and frequency tunability. In this work, we propose an integrated and tunable transducer that combines a coplanar waveguide microwave resonator with a magno-optomechanical microcavity via flip-chip bonding. Benefiting from the broad frequency tunability of the magnon mode, the working frequency range can be tuned over several gigahertz. Through optimization of the geometry and pump powers, our design achieves a theoretical microwave-to-optical photon conversion efficiency exceeding 50% using experimentally achievable parameters, alongside a bandwidth greater than 10 kHz. An added noise near the quantum limit $(\ensuremath{\sim}1)$ is achievable at 10 mK using lower pump powers at the cost of conversion efficiency or a pulsed-pump protocol. By merging compact integration with wide frequency tunability, this platform offers a promising pathway toward scalable quantum networks.
State transfer between light and microwaves is a key challenge in quantum networks. Promising transducers use a mechanical intermediary that couples to both fields via radiation pressure. Such electro-optomechanical devices have achieved high efficiencies, yet require resolved-sideband cavities, and generally compromise in scalability and noise performance. Here, we relax this constraint by extending the protocol of Navarathna et al. that transfers optical quantum information onto a mechanical resonator using a broadband, sideband-unresolved cavity and feedback. Combining this with parametric mechanical-to-microwave conversion, we show that continuous optical-to-microwave quantum state transfer is possible using measurement-based feedback, while all-optical coherent feedback enables bidirectional transfer. To assess the transfer, we introduce the quantum transfer witness WT, which -- though similar to the input-referred added noise -- also identifies whether a channel is capable of both preserving Gaussian entanglement and outperforming classical transduction schemes. Finally, we show that quantum-compatible noise performance is within reach of current experimental capabilities. Our results unlock a new design space for electro-optomechanical transducers and strengthens their candidacy as scalable quantum links between distant nodes.