Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1008.1277 · Applied Physics Letters

Low-crosstalk bifurcation detectors for coupled flux qubits

P. C. de Groot, Arjan F. van Loo, Jürgen Lisenfeld, Raymond N. Schouten, Adrian Lupaşcu, C. J. P. M. Harmans, Johan E. Mooij

Published Mar 22, 2010• 8 citations
arXivHTMLPDF

Abstract

We present experimental results on the crosstalk between two ac-operated dispersive bifurcation detectors, implemented in a circuit for high-fidelity readout of two strongly coupled flux qubits. Both phase-dependent and phase-independent contributions to the crosstalk are analyzed. For proper tuning of the phase the measured crosstalk is 0.1% and the correlation between the measurement outcomes is less than 0.05%. These results show that bifurcative readout provides a reliable and generic approach for multipartite correlation experiments.

DOI
10.1063/1.3367875

Related papers

Improved qubit bifurcation readout in the straddling regime of circuit QED

Maxime Boissonneault, Jay Gambetta, Alexandre Blais

We study bifurcation measurement of a multilevel superconducting qubit using a nonlinear resonator biased in the straddling regime, where the resonator frequency sits between two qubit transition frequencies. We find that high-fidelity bifurcation measurements are possible because of the enhanced qubit-state-dependent pull of the resonator frequency, the behavior of qubit-induced nonlinearities, and the reduced Purcell decay rate of the qubit that can be realized in this regime. Numerical simulations find up to a threefold improvement in qubit readout fidelity when operating in, rather than outside of, the straddling regime. High-fidelity measurements can be obtained at much smaller qubit-resonator couplings than current typical experimental realizations, reducing spectral crowding and potentially simplifying the implementation of multiqubit devices.

arXiv:1206.1296•Physical Review A•Aug 23, 2012•16 citations

QUANTUM NON-DEMOLITION MEASUREMENT OF A SUPERCONDUCTING FLUX QUBIT

Johan E. Mooij

Measurements have been performed on superconducting flux qubits using a Josephson bifurcation amplifier (JBA). The qubit states are identified with the two stable dynamic states of a strongly driven non-linear oscillator that contains a SQUID sensor. Readout with high fidelity is achieved. Correlations in repeated measurements demonstrate that this readout is fully projective.

Foundations of Quantum Mechanics in the Light of New Technology•Jun 1, 2009•0 citations

Theoretical analysis of measurement crosstalk for coupled Josephson phase qubits

Abraham G. Kofman, Qin Zhang, John M. Martinis +1 more

We analyze the crosstalk error mechanism in measurement of two capacitively coupled superconducting flux-biased phase qubits. The damped oscillations of the superconducting phase after the measurement of the first qubit may significantly excite the second qubit, leading to its measurement error. The first qubit, which is highly excited after the measurement, is described classically. The second qubit is treated both classically and quantum mechanically. The results of the analysis are used to find the upper limit for the coupling capacitance (thus limiting the frequency of two-qubit operations) for a given tolerable value of the measurement error probability.

arXiv:cond-mat/0606078•Physical Review B•Jan 23, 2007•27 citations

Calibration of Flux Crosstalk in Large-Scale Flux-Tunable Superconducting Quantum Circuits

Xi Dai, Daniel Tennant, Robbyn Trappen +16 more

Magnetic flux tunability is an essential feature in most approaches to quantum computing based on superconducting qubits.Independent control of the fluxes in multiple loops is hampered by crosstalk.Calibrating flux crosstalk becomes a challenging task when the circuit elements interact strongly.We present a novel approach to flux crosstalk calibration, which is circuit model independent and relies on an iterative process to gradually improve calibration accuracy.This method allows us to reduce errors due to the inductive coupling between loops.The calibration procedure is automated and implemented on devices consisting of tunable flux qubits and couplers with up to 27 control loops.We devise a method to characterize the calibration error, which is used to show that the errors of the measured crosstalk coefficients are all below 0.17%.

arXiv:2105.14360•PRX Quantum•Oct 20, 2021•49 citations

Characterization and Control of Measurement-Induced Dephasing on Superconducting Flux Qubit with a Josephson Bifurcation Amplifier

Kosuke Kakuyanagi, Yuichiro Matsuzaki, Tatsuya Baba +3 more

Quantum measurements play a central role in quantum information processing. Understanding the mechanism of the quantum measurements is essential to both improve the visibility of the readout and decrease the projection error during measurement. Here, we describe and demonstrate an experimental protocol for quantifying a measurement backaction when we readout a superconducting flux qubit using a Josephson bifurcation amplifier. The coupling with the Josephson bifurcation amplifier induces a dephasing on the flux qubit during the readout. We have succeeded in estimating and controlling the strength of such a measurement-induced dephasing by changing the pulse height of the microwave driving. Our results are crucial for designing a suitable quantum readout technique for the realization of practical quantum devices.

Journal of the Physical Society of Japan•Sep 6, 2016•3 citations

Flux Crosstalk Calibration from Zero Knowledge to High Precision in Fully Tunable Superconducting Circuits

Y. Gao, Asier Galicia, J. R. Guimarães +9 more

Precise and independent flux control is essential for scalable superconducting processors built from frequency-tunable qubits and couplers, but flux crosstalk undermines it. Conventional calibration methods rely either on dedicated readout channels, which tunable couplers typically lack, or on readout schemes requiring extensive prior spectroscopy of the qubit and coupler. We demonstrate two independent methods that characterize coupler flux crosstalk without directly driving or measuring the couplers. The first method is zero-knowledge characterization, which exploits intrinsic coupler-resonator coupling to yield rapid and accurate estimates with no prior qubit or coupler spectroscopy, accelerating large scale bring-up. The second method is symmetric branch cancellation, which isolates crosstalk from other dispersive effects allowing for quantifying with high precision. Combined with an improved iterative procedure, these methods suppress residual coupler crosstalk below $5\times10^{-5}$, providing a complete route from zero-knowledge initialization to high-precision crosstalk characterization in fully tunable architectures.

arXiv:2611.06656•Nov 4, 2026•0 citations
We present experimental results on the crosstalk between two ac-operated dispersive bifurcation detectors, implemented in a circuit for high-fidelity readout of two strongly coupled flux qubits. Both phase-dependent and phase-independent contributions to the crosstalk are analyzed. For proper tuning of the phase the measured crosstalk is 0.1% and the correlation between the measurement outcomes is less than 0.05%. These results show that bifurcative readout provides a reliable and generic approach for multipartite correlation experiments.
We study bifurcation measurement of a multilevel superconducting qubit using a nonlinear resonator biased in the straddling regime, where the resonator frequency sits between two qubit transition frequencies. We find that high-fidelity bifurcation measurements are possible because of the enhanced qubit-state-dependent pull of the resonator frequency, the behavior of qubit-induced nonlinearities, and the reduced Purcell decay rate of the qubit that can be realized in this regime. Numerical simulations find up to a threefold improvement in qubit readout fidelity when operating in, rather than outside of, the straddling regime. High-fidelity measurements can be obtained at much smaller qubit-resonator couplings than current typical experimental realizations, reducing spectral crowding and potentially simplifying the implementation of multiqubit devices.
We analyze the crosstalk error mechanism in measurement of two capacitively coupled superconducting flux-biased phase qubits. The damped oscillations of the superconducting phase after the measurement of the first qubit may significantly excite the second qubit, leading to its measurement error. The first qubit, which is highly excited after the measurement, is described classically. The second qubit is treated both classically and quantum mechanically. The results of the analysis are used to find the upper limit for the coupling capacitance (thus limiting the frequency of two-qubit operations) for a given tolerable value of the measurement error probability.
Magnetic flux tunability is an essential feature in most approaches to quantum computing based on superconducting qubits.Independent control of the fluxes in multiple loops is hampered by crosstalk.Calibrating flux crosstalk becomes a challenging task when the circuit elements interact strongly.We present a novel approach to flux crosstalk calibration, which is circuit model independent and relies on an iterative process to gradually improve calibration accuracy.This method allows us to reduce errors due to the inductive coupling between loops.The calibration procedure is automated and implemented on devices consisting of tunable flux qubits and couplers with up to 27 control loops.We devise a method to characterize the calibration error, which is used to show that the errors of the measured crosstalk coefficients are all below 0.17%.
Quantum measurements play a central role in quantum information processing. Understanding the mechanism of the quantum measurements is essential to both improve the visibility of the readout and decrease the projection error during measurement. Here, we describe and demonstrate an experimental protocol for quantifying a measurement backaction when we readout a superconducting flux qubit using a Josephson bifurcation amplifier. The coupling with the Josephson bifurcation amplifier induces a dephasing on the flux qubit during the readout. We have succeeded in estimating and controlling the strength of such a measurement-induced dephasing by changing the pulse height of the microwave driving. Our results are crucial for designing a suitable quantum readout technique for the realization of practical quantum devices.
Precise and independent flux control is essential for scalable superconducting processors built from frequency-tunable qubits and couplers, but flux crosstalk undermines it. Conventional calibration methods rely either on dedicated readout channels, which tunable couplers typically lack, or on readout schemes requiring extensive prior spectroscopy of the qubit and coupler. We demonstrate two independent methods that characterize coupler flux crosstalk without directly driving or measuring the couplers. The first method is zero-knowledge characterization, which exploits intrinsic coupler-resonator coupling to yield rapid and accurate estimates with no prior qubit or coupler spectroscopy, accelerating large scale bring-up. The second method is symmetric branch cancellation, which isolates crosstalk from other dispersive effects allowing for quantifying with high precision. Combined with an improved iterative procedure, these methods suppress residual coupler crosstalk below 5×10−55\times10^{-5}5×10−5, providing a complete route from zero-knowledge initialization to high-precision crosstalk characterization in fully tunable architectures.