Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:0909.2464 · New Journal of Physics

Toward scalable ion traps for quantum information processing

Jason Amini, Hermann Uys, Janus H. Wesenberg, Signe Louise Seidelin, J. Britton, J. J. Bollinger, Dietrich G. Leibfried, C. Ospelkaus, Aaron P. VanDevender, David J. Wineland

Published Mar 16, 2010• 185 citations
arXivHTMLPDF

Abstract

In this paper, we report the design, fabrication and preliminary testing of a 150 zone ion trap array built in a 'surface-electrode' geometry microfabricated on a single substrate. We demonstrate the transport of atomic ions between the legs of a 'Y'-type junction and measure the in-situ heating rates for the ions. The trap design demonstrates the use of a basic component design library that can be quickly assembled to form structures optimized for a particular experiment.

DOI
10.1088/1367-2630/12/3/033031

Related papers

Reliable transport through a microfabricated X -junction surface-electrode ion trap

Kenneth Wright, Jason Amini, Daniel L. Faircloth +9 more

We report the design, fabrication and characterization of a microfabricated surface-electrode ion trap that supports controlled transport through the two-dimensional intersection of linear trapping zones arranged in a 90° cross. The trap is fabricated with very large scalable integration techniques which are compatible with scaling to a large quantum information processor. The shape of the radio-frequency electrodes is optimized with a genetic algorithm to reduce axial pseudopotential barriers and minimize ion heating during transport. Seventy-eight independent dc control electrodes enable fine control of the trapping potentials. We demonstrate reliable ion transport between junction legs and determine the rate of ion loss due to transport. Doppler-cooled ions survive more than 10 5 round-trip transits between junction legs without loss and more than 65 consecutive round trips without laser cooling.

arXiv:1210.3655•New Journal of Physics•Mar 4, 2013•89 citations

Microfabricated Surface-Electrode Ion Trap for Scalable Quantum Information Processing

Signe Louise Seidelin, John Chiaverini, R. Reichle +13 more

Individual laser-cooled 24Mg+ ions are confined in a linear Paul trap with a novel geometry where gold electrodes are located in a single plane and the ions are trapped 40 microm above this plane. The relatively simple trap design and fabrication procedure are important for large-scale quantum information processing (QIP) using ions. Measured ion motional frequencies are compared to simulations. Measurements of ion recooling after cooling is temporarily suspended yield a heating rate of approximately 5 motional quanta per millisecond for a trap frequency of 2.83 MHz, sufficiently low to be useful for QIP.

arXiv:quant-ph/0601173•Physical Review Letters•Jun 30, 2006•457 citations

Optimization and implementation of a surface-electrode ion trap junction

Chi Zhang, Karan K. Mehta, Jonathan Home

Abstract We describe the design of a surface-electrode ion trap junction, which is a key element for large-scale ion trap arrays. A bi-objective optimization method is used for designing the electrodes, which maintains the total pseudo-potential curvature while minimizing the axial pseudo-potential gradient along the ion transport path. To facilitate the laser beam delivery for parallel operations in multiple trap zones, we implemented integrated optics on each arm of this X-junction trap. The layout of the trap chip for commercial foundry fabrication is presented. This work suggests routes to improving ion trap junction performance in scalable implementations. Together with integrated optical addressing, this contributes to modular trapped-ion quantum computing in interconnected two-dimensional arrays.

arXiv:2201.12579•New Journal of Physics•Jul 1, 2022•10 citations

Monolithic microfabricated ion trap forquantum information processing

Fayaz A. Shaikh

The objective of this research is to design, fabricate, and demonstrate a microfabricated \nmonolithic ion trap for applications in quantum computation and quantum simulation. \nMost current microfabricated ion trap designs are based on planar-segmented surface electrodes. \nAlthough promising scalability to trap arrays containing ten to one hundred ions, \nthese planar designs suffer from the challenges of shallow trap depths, radial asymmetry of \nthe confining potential, and electrode charging resulting from laser interactions with dielectric \nsurfaces. In this research, the design, fabrication, and testing of a monolithic \nand symmetric two-level ion trap is presented. This ion trap overcomes the challenges of \nsurface-electrode ion traps. Numerical electrostatic simulations show that this symmetric \ntrap produces a deep (1 eV for 171Yb+ ion), radially symmetric RF confinement potential. \nThe trap has an angled through-chip slot that allows back-side ion loading and generous \nthrough laser access, while avoiding surface-light scattering and dielectric charging that \ncan corrupt the design control electrode compensating potentials. The geometry of the trap \nand its dimensions are optimized for trapping long and linear ion chains with equal spacing \nfor use with quantum simulation problems and quantum computation architectures.

•Mar 26, 2013•0 citations

TWO-DIMENSIONAL ARRAY OF ION TRAPS ON A PLANAR CHIP

Jinyin Wan, Yuzhu Wang, Liang Liu

We investigate a planar ion chip design with a two-dimensional array of linear ion traps for the scalable quantum information processor. The segmented electrodes reside in a single plane on a substrate and a grounded metal plate, a combination of appropriate rf and DC potentials are applied to them for stable ion confinement, and the trap axes are located above the surface at a distance controlled by the electrodes' lateral extent and the substrate's height as discussed. The potential distributions are calculated using static electric field qualitatively. This architecture is conceptually simple and many current microfabrication techniques are feasible for the basic structure. It may provide a promising route for scalable quantum computers.

Modern Physics Letters B•Jan 10, 2009•1 citation

The development of microfabricated ion traps towards quantum information and simulation

Marcus Hughes

Trapped ions within Paul traps have shown to be a promising architecture in the realisation of a quantum information processor together with the ability of providing quantum simulations. Linear Paul traps have demonstrated long coherence times with ions being well isolated from the environment, single and multi-qubit gates and the high fidelity detection of states. The scalability to large number of qubits, incorporating all the previous achievements requires an array of linear ion traps. Microfabrication techniques allow for fabrication and micron level accuracy of the trap electrode dimensions through photolithography techniques. The first part of this thesis presents the experiential setup and trapping of Yb+ ions needed to test large ion trap arrays. This include vacuum systems that can host advanced symmetric and asymmetric ion traps with up to 90 static voltage control electrodes. Demonstration of a single trapped Yb+ ion within a two-layer macroscopic ion trap is presented. with an ion-electrode distance of 310(10) µm. The anomalous heating rate and spectral noise density of the trap was measured, a main form of decoherence within ion traps. The second half of this thesis presents the design and fabrication of multi-layer asymmetric ion traps. This allows for isolated electrodes that cannot be accessed via surface pathways, allowing for higher density of electrodes as well as creating novel trap designs that allow for the potential of quantum simulations to be demonstrated. These include two-dimensional lattices and ring trap designs in which the isolated electrodes provide more control in the ion position. For the microfabrication of these traps I present a novel high-aspect ratio electroplated electrode design that provides shielding of the dielectric layer. This provides a means to mitigate stray electric field due to charge build up on the dielectric surfaces. Electrical testing of the trap structures was performed to test bulk breakdown and surface flashover of the ion trap architectures. Results showed sufficient isolation between electrodes for both radio frequency and static breakdown. Surface flashover voltage measurements over the dielectric layer showed an improvement of more than double over previous results using a new fabrication technique. This will allow for more powerful ion trap chips needed for the next generation of microfabricated ion trap arrays for scalable quantum technologies.

•Jun 16, 2013•0 citations
In this paper, we report the design, fabrication and preliminary testing of a 150 zone ion trap array built in a 'surface-electrode' geometry microfabricated on a single substrate. We demonstrate the transport of atomic ions between the legs of a 'Y'-type junction and measure the in-situ heating rates for the ions. The trap design demonstrates the use of a basic component design library that can be quickly assembled to form structures optimized for a particular experiment.
We report the design, fabrication and characterization of a microfabricated surface-electrode ion trap that supports controlled transport through the two-dimensional intersection of linear trapping zones arranged in a 90° cross. The trap is fabricated with very large scalable integration techniques which are compatible with scaling to a large quantum information processor. The shape of the radio-frequency electrodes is optimized with a genetic algorithm to reduce axial pseudopotential barriers and minimize ion heating during transport. Seventy-eight independent dc control electrodes enable fine control of the trapping potentials. We demonstrate reliable ion transport between junction legs and determine the rate of ion loss due to transport. Doppler-cooled ions survive more than 10 5 round-trip transits between junction legs without loss and more than 65 consecutive round trips without laser cooling.
Individual laser-cooled 24Mg+ ions are confined in a linear Paul trap with a novel geometry where gold electrodes are located in a single plane and the ions are trapped 40 microm above this plane. The relatively simple trap design and fabrication procedure are important for large-scale quantum information processing (QIP) using ions. Measured ion motional frequencies are compared to simulations. Measurements of ion recooling after cooling is temporarily suspended yield a heating rate of approximately 5 motional quanta per millisecond for a trap frequency of 2.83 MHz, sufficiently low to be useful for QIP.
Abstract We describe the design of a surface-electrode ion trap junction, which is a key element for large-scale ion trap arrays. A bi-objective optimization method is used for designing the electrodes, which maintains the total pseudo-potential curvature while minimizing the axial pseudo-potential gradient along the ion transport path. To facilitate the laser beam delivery for parallel operations in multiple trap zones, we implemented integrated optics on each arm of this X-junction trap. The layout of the trap chip for commercial foundry fabrication is presented. This work suggests routes to improving ion trap junction performance in scalable implementations. Together with integrated optical addressing, this contributes to modular trapped-ion quantum computing in interconnected two-dimensional arrays.
The objective of this research is to design, fabricate, and demonstrate a microfabricated \nmonolithic ion trap for applications in quantum computation and quantum simulation. \nMost current microfabricated ion trap designs are based on planar-segmented surface electrodes. \nAlthough promising scalability to trap arrays containing ten to one hundred ions, \nthese planar designs suffer from the challenges of shallow trap depths, radial asymmetry of \nthe confining potential, and electrode charging resulting from laser interactions with dielectric \nsurfaces. In this research, the design, fabrication, and testing of a monolithic \nand symmetric two-level ion trap is presented. This ion trap overcomes the challenges of \nsurface-electrode ion traps. Numerical electrostatic simulations show that this symmetric \ntrap produces a deep (1 eV for 171Yb+ ion), radially symmetric RF confinement potential. \nThe trap has an angled through-chip slot that allows back-side ion loading and generous \nthrough laser access, while avoiding surface-light scattering and dielectric charging that \ncan corrupt the design control electrode compensating potentials. The geometry of the trap \nand its dimensions are optimized for trapping long and linear ion chains with equal spacing \nfor use with quantum simulation problems and quantum computation architectures.
We investigate a planar ion chip design with a two-dimensional array of linear ion traps for the scalable quantum information processor. The segmented electrodes reside in a single plane on a substrate and a grounded metal plate, a combination of appropriate rf and DC potentials are applied to them for stable ion confinement, and the trap axes are located above the surface at a distance controlled by the electrodes' lateral extent and the substrate's height as discussed. The potential distributions are calculated using static electric field qualitatively. This architecture is conceptually simple and many current microfabrication techniques are feasible for the basic structure. It may provide a promising route for scalable quantum computers.
Trapped ions within Paul traps have shown to be a promising architecture in the realisation of a quantum information processor together with the ability of providing quantum simulations. Linear Paul traps have demonstrated long coherence times with ions being well isolated from the environment, single and multi-qubit gates and the high fidelity detection of states. The scalability to large number of qubits, incorporating all the previous achievements requires an array of linear ion traps. Microfabrication techniques allow for fabrication and micron level accuracy of the trap electrode dimensions through photolithography techniques. The first part of this thesis presents the experiential setup and trapping of Yb+ ions needed to test large ion trap arrays. This include vacuum systems that can host advanced symmetric and asymmetric ion traps with up to 90 static voltage control electrodes. Demonstration of a single trapped Yb+ ion within a two-layer macroscopic ion trap is presented. with an ion-electrode distance of 310(10) µm. The anomalous heating rate and spectral noise density of the trap was measured, a main form of decoherence within ion traps. The second half of this thesis presents the design and fabrication of multi-layer asymmetric ion traps. This allows for isolated electrodes that cannot be accessed via surface pathways, allowing for higher density of electrodes as well as creating novel trap designs that allow for the potential of quantum simulations to be demonstrated. These include two-dimensional lattices and ring trap designs in which the isolated electrodes provide more control in the ion position. For the microfabrication of these traps I present a novel high-aspect ratio electroplated electrode design that provides shielding of the dielectric layer. This provides a means to mitigate stray electric field due to charge build up on the dielectric surfaces. Electrical testing of the trap structures was performed to test bulk breakdown and surface flashover of the ion trap architectures. Results showed sufficient isolation between electrodes for both radio frequency and static breakdown. Surface flashover voltage measurements over the dielectric layer showed an improvement of more than double over previous results using a new fabrication technique. This will allow for more powerful ion trap chips needed for the next generation of microfabricated ion trap arrays for scalable quantum technologies.