Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:0901.1146 · IEEE Transactions on Applied Superconductivity

Niobium Superconducting Nanowire Single-Photon Detectors

A.J. Annunziata, Daniel F. Santavicca, J.D. Chudow, Luigi Frunzio, Michael J. Rooks, A. Frydman, D.E. Prober

Published Jun 1, 2009• 57 citations
arXivHTMLPDF

Abstract

We investigate the performance of superconducting nanowire photon detectors fabricated from ultra-thin Nb. A direct comparison is made between these detectors and similar nanowire detectors fabricated from NbN. We find that Nb detectors are significantly more susceptible than NbN to thermal instability (latching) at high bias. We show that the devices can be stabilized by reducing the input resistance of the readout. Nb detectors optimized in this way are shown to have approximately 2/3 the reset time of similar large-active-area NbN detectors of the same geometry, with approximately 6% detection efficiency for single photons at 470 nm.

DOI
10.1109/tasc.2009.2018740

Related papers

Superconducting niobium nanowire single photon detectors

Anthony J. Annunziata, A. Frydman, Matthew O. Reese +3 more

We have fabricated and tested single photon detectors based on a current biased superconducting niobium nanowire patterned into a meander. The detectors are fabricated from high quality, ultra high vacuum sputtered niobium thin films on a sapphire substrate. For detection of single optical photons, we show that the superconductor's intrinsic kinetic inductance does not limit the reset time of the detector, which is ≈ 2 nanoseconds, in contrast to the longer reset times seen in niobium nitride detectors of similar size and geometry. We also describe a readout scheme for photon counting that is unique to Nb due to its lower resistivity. These detectors have applications in imaging of infrared photoemission from CMOS logic circuits as well as in optical communications and quantum information processing.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Oct 18, 2006•14 citations

Reset dynamics and latching in niobium superconducting nanowire single-photon detectors

Anthony J. Annunziata, Orlando Quaranta, Daniel F. Santavicca +8 more

We study the reset dynamics of niobium (Nb) superconducting nanowire single-photon detectors (SNSPDs) using experimental measurements and numerical simulations. The numerical simulations of the detection dynamics agree well with experimental measurements, using independently determined parameters in the simulations. We find that if the photon-induced hotspot cools too slowly, the device will latch into a dc resistive state. To avoid latching, the time for the hotspot to cool must be short compared to the inductive time constant that governs the resetting of the current in the device after hotspot formation. From simulations of the energy relaxation process, we find that the hotspot cooling time is determined primarily by the temperature-dependent electron-phonon inelastic time. Latching prevents reset and precludes subsequent photon detection. Fast resetting to the superconducting state is, therefore, essential, and we demonstrate experimentally how this is achieved. We compare our results to studies of reset and latching in niobium nitride SNSPDs.

arXiv:1008.0895•Journal of Applied Physics•Oct 15, 2010•127 citations

Design of efficient superconducting nanowire single photon detectors for near-infrared wavelengths

M. J. A. de Dood

Superconducting single photon detectors consist of a narrow and thin wire of superconductor and can detect single photons with high efficiency and high speed. Simultaneous optimization of the detection efficiency and detector response time is difficult because the response time is set by the dimensions of the wire (cross section and length) while the detection efficiency is determined by both the internal detection mechanism and the dimensions of the wire. Wider and shorter wires are easier to fabricate, are more robust and lead to shorter detector reset time, but are generally less efficient. Experiments employing detector tomography provide important insights into the photon detection mechanism and indicate a detection mechanism where the edges of the wire are more efficient. This leads to a position dependent local detection efficiency that can be explained in the context of a photon-assisted-vortex-entry model and predicts an optimum wire width ~70 nm. A 50 nm wide silicon nanowire deposited on top of a 150 nm wide NbN nanowire directs light at 1550 nm wavelength to the edges and improves both the total absorption efficiency and the internal detection efficiency of the wire. The total absorption efficiency can be enhanced by 30% while the internal detection efficiency is increased by 70%. Assuming that the wire covers a similar area the detector response time is reduced 4-fold compared to the standard design using a 70 nm wide wire.

Advanced Photon Counting Techniques•May 14, 2018•0 citations

Comparison of Superconducting Nanowire Single-Photon Detectors Made of NbTiN and NbN Thin Films

Xiaoyan Yang, Lixing You, Lu Zhang +5 more

We fabricated superconducting nanowire single-photon detectors (SNSPDs) made of NbTiN and NbN thin films in the same fabrication batch. Various parameters, such as critical temperature, resistivity, switching current, and kinetic inductance, were compared between the two types of SNSPDs. These data indicate that NbTiN SNSPD surpasses NbN SNSPD in many aspects, including a shorter recovery time due to smaller kinetic inductance, a lower timing jitter due to higher switching current, and better uniformity. Based on the measurement of 28 out of 121 NbTiN SNSPDs on a 2-in Si wafer, 71% of detectors show a system detection efficiency of over 50% at a dark count rate of 100 Hz, with the maximum efficiency being 77.5%.

IEEE Transactions on Applied Superconductivity•Nov 22, 2017•45 citations

Large sensitive-area NbN nanowire superconducting single-photon detectors fabricated on single-crystal MgO substrates

Shigehito Miki, Mikio Fujiwara, Masahide Sasaki +5 more

We report on the performance of large area NbN nanowire superconducting single-photon detectors (SSPDs). 20×20μm2 area SSPDs with 80 and 100nm linewidths and 50% fill factor were fabricated in 4-nm-thick NbN films grown on single-crystal MgO substrates. The high quality of the devices was verified by electrical and optical testing and compares favorably to measurements of 10×10μm2 area SSPDs. Measurements of kinetic inductance versus bias current indicate that the constriction density is low. The fiber-coupled detection efficiency of the devices was 0.4%–3.5% at 100Hz dark count rate.

Applied Physics Letters•Feb 11, 2008•119 citations

Bias sputtered NbN and superconducting nanowire devices

Andrew E. Dane, Adam N. McCaughan, Di Zhu +6 more

Superconducting nanowire single photon detectors (SNSPDs) promise to combine near-unity quantum efficiency with >100 megacounts per second rates, picosecond timing jitter, and sensitivity ranging from x-ray to mid-infrared wavelengths. However, this promise is not yet fulfilled, as superior performance in all metrics is yet to be combined into one device. The highest single-pixel detection efficiency and the widest bias windows for saturated quantum efficiency have been achieved in SNSPDs based on amorphous materials, while the lowest timing jitter and highest counting rates were demonstrated in devices made from polycrystalline materials. Broadly speaking, the amorphous superconductors that have been used to make SNSPDs have higher resistivities and lower critical temperature (Tc) values than typical polycrystalline materials. Here, we demonstrate a method of preparing niobium nitride (NbN) that has lower-than-typical superconducting transition temperature and higher-than-typical resistivity. As we will show, NbN deposited onto unheated SiO2 has a low Tc and high resistivity but is too rough for fabricating unconstricted nanowires, and Tc is too low to yield SNSPDs that can operate well at liquid helium temperatures. By adding a 50 W RF bias to the substrate holder during sputtering, the Tc of the unheated NbN films was increased by up to 73%, and the roughness was substantially reduced. After optimizing the deposition for nitrogen flow rates, we obtained 5 nm thick NbN films with a Tc of 7.8 K and a resistivity of 253 μΩ cm. We used this bias sputtered room temperature NbN to fabricate SNSPDs. Measurements were performed at 2.5 K using 1550 nm light. Photon count rates appeared to saturate at bias currents approaching the critical current, indicating that the device's quantum efficiency was approaching unity. We measured a single-ended timing jitter of 38 ps. The optical coupling to these devices was not optimized; however, integration with front-side optical structures to improve absorption should be straightforward. This material preparation was further used to fabricate nanocryotrons and a large-area imager device, reported elsewhere. The simplicity of the preparation and promising device performance should enable future high-performance devices.

Applied Physics Letters•Sep 18, 2017•67 citations
We investigate the performance of superconducting nanowire photon detectors fabricated from ultra-thin Nb. A direct comparison is made between these detectors and similar nanowire detectors fabricated from NbN. We find that Nb detectors are significantly more susceptible than NbN to thermal instability (latching) at high bias. We show that the devices can be stabilized by reducing the input resistance of the readout. Nb detectors optimized in this way are shown to have approximately 2/3 the reset time of similar large-active-area NbN detectors of the same geometry, with approximately 6% detection efficiency for single photons at 470 nm.
We have fabricated and tested single photon detectors based on a current biased superconducting niobium nanowire patterned into a meander. The detectors are fabricated from high quality, ultra high vacuum sputtered niobium thin films on a sapphire substrate. For detection of single optical photons, we show that the superconductor's intrinsic kinetic inductance does not limit the reset time of the detector, which is ≈ 2 nanoseconds, in contrast to the longer reset times seen in niobium nitride detectors of similar size and geometry. We also describe a readout scheme for photon counting that is unique to Nb due to its lower resistivity. These detectors have applications in imaging of infrared photoemission from CMOS logic circuits as well as in optical communications and quantum information processing.
We study the reset dynamics of niobium (Nb) superconducting nanowire single-photon detectors (SNSPDs) using experimental measurements and numerical simulations. The numerical simulations of the detection dynamics agree well with experimental measurements, using independently determined parameters in the simulations. We find that if the photon-induced hotspot cools too slowly, the device will latch into a dc resistive state. To avoid latching, the time for the hotspot to cool must be short compared to the inductive time constant that governs the resetting of the current in the device after hotspot formation. From simulations of the energy relaxation process, we find that the hotspot cooling time is determined primarily by the temperature-dependent electron-phonon inelastic time. Latching prevents reset and precludes subsequent photon detection. Fast resetting to the superconducting state is, therefore, essential, and we demonstrate experimentally how this is achieved. We compare our results to studies of reset and latching in niobium nitride SNSPDs.
Superconducting single photon detectors consist of a narrow and thin wire of superconductor and can detect single photons with high efficiency and high speed. Simultaneous optimization of the detection efficiency and detector response time is difficult because the response time is set by the dimensions of the wire (cross section and length) while the detection efficiency is determined by both the internal detection mechanism and the dimensions of the wire. Wider and shorter wires are easier to fabricate, are more robust and lead to shorter detector reset time, but are generally less efficient. Experiments employing detector tomography provide important insights into the photon detection mechanism and indicate a detection mechanism where the edges of the wire are more efficient. This leads to a position dependent local detection efficiency that can be explained in the context of a photon-assisted-vortex-entry model and predicts an optimum wire width ~70 nm. A 50 nm wide silicon nanowire deposited on top of a 150 nm wide NbN nanowire directs light at 1550 nm wavelength to the edges and improves both the total absorption efficiency and the internal detection efficiency of the wire. The total absorption efficiency can be enhanced by 30% while the internal detection efficiency is increased by 70%. Assuming that the wire covers a similar area the detector response time is reduced 4-fold compared to the standard design using a 70 nm wide wire.
We fabricated superconducting nanowire single-photon detectors (SNSPDs) made of NbTiN and NbN thin films in the same fabrication batch. Various parameters, such as critical temperature, resistivity, switching current, and kinetic inductance, were compared between the two types of SNSPDs. These data indicate that NbTiN SNSPD surpasses NbN SNSPD in many aspects, including a shorter recovery time due to smaller kinetic inductance, a lower timing jitter due to higher switching current, and better uniformity. Based on the measurement of 28 out of 121 NbTiN SNSPDs on a 2-in Si wafer, 71% of detectors show a system detection efficiency of over 50% at a dark count rate of 100 Hz, with the maximum efficiency being 77.5%.
We report on the performance of large area NbN nanowire superconducting single-photon detectors (SSPDs). 20×20μm2 area SSPDs with 80 and 100nm linewidths and 50% fill factor were fabricated in 4-nm-thick NbN films grown on single-crystal MgO substrates. The high quality of the devices was verified by electrical and optical testing and compares favorably to measurements of 10×10μm2 area SSPDs. Measurements of kinetic inductance versus bias current indicate that the constriction density is low. The fiber-coupled detection efficiency of the devices was 0.4%–3.5% at 100Hz dark count rate.
Superconducting nanowire single photon detectors (SNSPDs) promise to combine near-unity quantum efficiency with >100 megacounts per second rates, picosecond timing jitter, and sensitivity ranging from x-ray to mid-infrared wavelengths. However, this promise is not yet fulfilled, as superior performance in all metrics is yet to be combined into one device. The highest single-pixel detection efficiency and the widest bias windows for saturated quantum efficiency have been achieved in SNSPDs based on amorphous materials, while the lowest timing jitter and highest counting rates were demonstrated in devices made from polycrystalline materials. Broadly speaking, the amorphous superconductors that have been used to make SNSPDs have higher resistivities and lower critical temperature (Tc) values than typical polycrystalline materials. Here, we demonstrate a method of preparing niobium nitride (NbN) that has lower-than-typical superconducting transition temperature and higher-than-typical resistivity. As we will show, NbN deposited onto unheated SiO2 has a low Tc and high resistivity but is too rough for fabricating unconstricted nanowires, and Tc is too low to yield SNSPDs that can operate well at liquid helium temperatures. By adding a 50 W RF bias to the substrate holder during sputtering, the Tc of the unheated NbN films was increased by up to 73%, and the roughness was substantially reduced. After optimizing the deposition for nitrogen flow rates, we obtained 5 nm thick NbN films with a Tc of 7.8 K and a resistivity of 253 μΩ cm. We used this bias sputtered room temperature NbN to fabricate SNSPDs. Measurements were performed at 2.5 K using 1550 nm light. Photon count rates appeared to saturate at bias currents approaching the critical current, indicating that the device's quantum efficiency was approaching unity. We measured a single-ended timing jitter of 38 ps. The optical coupling to these devices was not optimized; however, integration with front-side optical structures to improve absorption should be straightforward. This material preparation was further used to fabricate nanocryotrons and a large-area imager device, reported elsewhere. The simplicity of the preparation and promising device performance should enable future high-performance devices.