Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:quant-ph/0008111 · Physical Review Letters

Magnetic Conveyor Belt for Transporting and Merging Trapped Atom Clouds

W. Hänsel, Jakob Reichel, Peter Hommelhoff, Theodor W. Hänsch

Published Jan 22, 2001• 188 citations
arXivHTMLPDF

Abstract

We demonstrate an integrated magnetic device which transports cold atoms near a surface with very high positioning accuracy. Time-dependent currents in a lithographic conductor pattern create a moving chain of potential wells; atoms are transported in these wells while remaining confined in all three dimensions. We achieve mean fluxes up to 10(6) s(-1) with a negligible heating rate. An extension of this device allows merging of atom clouds by unification of two Ioffe-Pritchard potentials. The unification, which we demonstrate experimentally, can be performed without loss of phase space density. This novel, all-magnetic atom manipulation offers exciting perspectives, such as trapped-atom interferometry.

DOI
10.1103/physrevlett.86.608

Related papers

Transporting, splitting and merging of atomic ensembles in a chip trap

Peter Hommelhoff, W Hänsel, T. Steinmetz +2 more

We present a toolbox for cold atom manipulation with time-dependent magnetic fields generated by an atom chip. Wire layouts, detailed experimental procedures and results are presented for the following experiments: use of a magnetic conveyor belt for positioning of cold atoms and Bose–Einstein condensates (BECs) with a potential resolution of 2 nm; splitting of thermal clouds and BECs in adjustable magnetic double-well potentials; and controlled splitting of a cold reservoir. The devices that enable these manipulations can be combined with each other. We demonstrate this by combining reservoir splitter and conveyor belt to obtain a cold atom dispenser. We discuss the importance of these devices for quantum information processing, atom interferometry and Josephson junction physics on the chip. For all devices, absorption-image video sequences are provided to demonstrate their time-dependent behaviour.

arXiv:quant-ph/0411012•New Journal of Physics•Jan 12, 2005•63 citations

Three magnetic devices for atom optics

Philip F. Schewe

Have been demonstrated: a beam splitter, a conveyor belt, and a switch. Just as electrons drive electronics and photons drive photonics, many researchers hope that cold, neutral atoms will drive a future “atomtronics.” To process information, atoms will need to be manipulated on or near an “atom chip” using atom-based analogs of mirrors, lenses, waveguides, gratings, and other devices. The new devices reported here all exploit the interaction between a neutral atom’s magnetic moment and an external magnetic field with a gradient strong enough to create microscopic potentials. Jörg Schmiedmayer of the University of Heidelberg and his colleagues have designed a beam splitter for guided atoms, using a Y-shaped current-carrying wire nanofabricated on a surface. Depending on how current is sent through the Y, atoms can be directed to the output arms with any desired ratio. A group at the Max Planck Institute for Quantum Optics in Munich has been able to confine atom clouds in separate potential wells and transport them with 800-nm precision near a surface having time-dependent currents in a lithographically patterned conductor. The researchers have used their “magnetic conveyor belt” to merge separate clouds; their evidence shows that the process is adiabatic and can be reversed to coherently split wavepackets. Also using lithography, and following their own beam splitter, a group at the University of Colorado and NIST in Boulder has devised a switch that can direct a guided beam of neutral atoms to either of two output ports separated by 8 mm. Both the incoming and outgoing atoms are guided between two parallel wires having current flowing in the same direction. In the switch region, the atoms are guided alongside two wires with oppositely flowing current. (D. Cassettari et al., Phys. Rev. Lett. 85, 5483, 2000 http://dx.doi.org/10.1103/PhysRevLett.85.5483 . W. Hänsel et al., Phys. Rev. Lett. 86, 608, 2001 http://dx.doi.org/10.1103/PhysRevLett.86.608 . D. Müller et al., Opt. Lett. 25, 1382, 2000 http://dx.doi.org/10.1364/OL.25.001382 ; D. Müller et al., Phys. Rev. A , in press.)© 2001 American Institute of Physics.

Physics Today•Feb 1, 2001•0 citations

Transport of atom packets in a train of Ioffe-Pritchard traps

Thierry Lahaye, Gael Reinaudi, Z. Wang +2 more

We demonstrate transport and evaporative cooling of several atomic clouds in a chain of magnetic Ioffe-Pritchard traps moving at a low speed $(<1\phantom{\rule{0.3em}{0ex}}\mathrm{m}∕\mathrm{s})$. The trapping scheme relies on the use of a magnetic guide for transverse confinement and of magnets fixed on a conveyor belt for longitudinal trapping. This experiment introduces a different approach for parallelizing the production of Bose-Einstein condensates as well as for the realization of a continuous atom laser.

arXiv:cond-mat/0605302•Physical Review A•Sep 28, 2006•19 citations

Efficient loading of a magnetic waveguide on an atom chip

Peter D. D. Schwindt, Eric Cornell, T. Kishimoto +2 more

We demonstrate efficient loading of neutral atoms into a magnetic waveguide produced by the magnetic fields of microfabricated current-carrying conductors. The lithographically patterned conductors on this ``atom chip'' can be used to make a variety of guiding and trapping structures for manipulating cold atoms and Bose-Einstein condensates. A three-chamber vacuum apparatus collects atoms in a magneto-optical trap, precools them via evaporative cooling, and delivers them to the final chamber containing the atom chip. We describe in detail how the precooled atomic cloud is transferred from a macroscopic magnetic Ioffe-Pritchard trap to the microscopic magnetic waveguide on the atom chip $21\phantom{\rule{0.3em}{0ex}}\mathrm{cm}$ away. Permanent magnets provide a confining two-dimensional quadrupole field to guide the atoms between the two chambers while longitudinally the cloud is allowed to freely expand during the transfer. Strategically placed coils are used to control the longitudinal size and speed of the atomic cloud as it is loaded on the atom chip.

Physical Review A•Aug 18, 2005•13 citations

A minimalistic and optimized conveyor belt for neutral atoms

Ritayan Roy, Paul C. Condylis, Vindhiya Prakash +2 more

Abstract Here we report of a design and the performance of an optimized micro-fabricated conveyor belt for precise and adiabatic transportation of cold atoms. A theoretical model is presented to determine optimal currents in conductors used for the transportation. We experimentally demonstrate a fast adiabatic transportation of Rubidium (87Rb) cold atoms with minimal loss and heating with as few as three conveyor belt conductors. This novel design of a multilayered conveyor belt structure is fabricated in aluminium nitride (AlN) because of its outstanding thermal and electrical properties. This demonstration would pave a way for a compact and portable quantum device required for quantum information processing and sensors, where precise positioning of cold atoms is desirable.

arXiv:1704.03030•Scientific Reports•Oct 16, 2017•10 citations

A cold atom apparatus for the microscopy of thin membranes

Amruta Gadge

Ultracold atomic gases can be utilised as extremely sensitive probes of their surrounding environment. In particular, samples of ultracold atoms confined using chip-based microtraps are an ideal tool for mapping electric and magnetic field landscapes. Over the course of this thesis, a new experiment capable of performing surface microscopy using magnetically trapped clouds of cold rubidium-87 atoms has been built. The focus of the work is on the design and construction of the experimental system, which must incorporate many different aspects for manipulating thermal atomic gases, with a view to positioning them at sub-micron distances from special surfaces. This reduced atom-surface separation is necessary for implementing a high resolution, high sensitivity magnetic field sensor with cold atoms. Although current microfabrication techniques easily enable trapping at distances on the order of micrometres, several distance-dependent surface effects - such as the Casimir-Polder force, Johnson-Nyquist noise, and stray potentials - eventually impede magnetic trapping at the sub-micron level. These surface effects can greatly modify the confining potentials, which reduces the trap depth and consequently leads to an additional loss rate of atoms from the trap. We have explored the possibility of using special surfaces such as nano-membranes of silicon nitride and graphene, which have reduced atom- surface interactions, to enable trapping distances at the sub-micron level. A multilayer printed circuit board chip has been designed to form an initial magnetic trap and then transport the cloud of atoms to a desired location over the samples. This chip, along with various samples, is mounted on a custom-made electrical feedthrough designed to make connections to all conductor that are inside the vacuum chamber. The initial cloud of cold atoms can then be prepared in the central region of the chip and delivered to the location of the samples on either side. The experimental system is able to routinely capture over 10^8 rubidium-87 atoms at a temperature of 80 micro-Kelvin in a magneto-optical trap using a novel scheme of five laser beams. A method is demonstrated for enhancing the atom number in the magneto-optical traps by a factor of two by using laser beams with two slightly different frequencies. Atoms from the magneto-optical trap are then transferred to a purely magnetic trap formed by the wires on the printed circuit board chip. Time-dependent currents in the chip wires then create a dynamic potential, which is shown to successfully transport the atomic sample over a distance of 12 millimetre with minimal atom loss. This thesis describes the development of the apparatus in detail, along with careful characterisation of the cold cloud at various stages of the experimental sequence. Initial results on the long distance atom transport are presented. Finally, the experimental results of the two frequency magneto-optical trap for atom number improvement are discussed.

•Jul 19, 2018•0 citations
We demonstrate an integrated magnetic device which transports cold atoms near a surface with very high positioning accuracy. Time-dependent currents in a lithographic conductor pattern create a moving chain of potential wells; atoms are transported in these wells while remaining confined in all three dimensions. We achieve mean fluxes up to 10(6) s(-1) with a negligible heating rate. An extension of this device allows merging of atom clouds by unification of two Ioffe-Pritchard potentials. The unification, which we demonstrate experimentally, can be performed without loss of phase space density. This novel, all-magnetic atom manipulation offers exciting perspectives, such as trapped-atom interferometry.
We present a toolbox for cold atom manipulation with time-dependent magnetic fields generated by an atom chip. Wire layouts, detailed experimental procedures and results are presented for the following experiments: use of a magnetic conveyor belt for positioning of cold atoms and Bose–Einstein condensates (BECs) with a potential resolution of 2 nm; splitting of thermal clouds and BECs in adjustable magnetic double-well potentials; and controlled splitting of a cold reservoir. The devices that enable these manipulations can be combined with each other. We demonstrate this by combining reservoir splitter and conveyor belt to obtain a cold atom dispenser. We discuss the importance of these devices for quantum information processing, atom interferometry and Josephson junction physics on the chip. For all devices, absorption-image video sequences are provided to demonstrate their time-dependent behaviour.
Have been demonstrated: a beam splitter, a conveyor belt, and a switch. Just as electrons drive electronics and photons drive photonics, many researchers hope that cold, neutral atoms will drive a future “atomtronics.” To process information, atoms will need to be manipulated on or near an “atom chip” using atom-based analogs of mirrors, lenses, waveguides, gratings, and other devices. The new devices reported here all exploit the interaction between a neutral atom’s magnetic moment and an external magnetic field with a gradient strong enough to create microscopic potentials. Jörg Schmiedmayer of the University of Heidelberg and his colleagues have designed a beam splitter for guided atoms, using a Y-shaped current-carrying wire nanofabricated on a surface. Depending on how current is sent through the Y, atoms can be directed to the output arms with any desired ratio. A group at the Max Planck Institute for Quantum Optics in Munich has been able to confine atom clouds in separate potential wells and transport them with 800-nm precision near a surface having time-dependent currents in a lithographically patterned conductor. The researchers have used their “magnetic conveyor belt” to merge separate clouds; their evidence shows that the process is adiabatic and can be reversed to coherently split wavepackets. Also using lithography, and following their own beam splitter, a group at the University of Colorado and NIST in Boulder has devised a switch that can direct a guided beam of neutral atoms to either of two output ports separated by 8 mm. Both the incoming and outgoing atoms are guided between two parallel wires having current flowing in the same direction. In the switch region, the atoms are guided alongside two wires with oppositely flowing current. (D. Cassettari et al., Phys. Rev. Lett. 85, 5483, 2000 http://dx.doi.org/10.1103/PhysRevLett.85.5483 . W. Hänsel et al., Phys. Rev. Lett. 86, 608, 2001 http://dx.doi.org/10.1103/PhysRevLett.86.608 . D. Müller et al., Opt. Lett. 25, 1382, 2000 http://dx.doi.org/10.1364/OL.25.001382 ; D. Müller et al., Phys. Rev. A , in press.)© 2001 American Institute of Physics.
We demonstrate transport and evaporative cooling of several atomic clouds in a chain of magnetic Ioffe-Pritchard traps moving at a low speed (<1m∕s)(<1\phantom{\rule{0.3em}{0ex}}\mathrm{m}∕\mathrm{s})(<1m∕s). The trapping scheme relies on the use of a magnetic guide for transverse confinement and of magnets fixed on a conveyor belt for longitudinal trapping. This experiment introduces a different approach for parallelizing the production of Bose-Einstein condensates as well as for the realization of a continuous atom laser.
We demonstrate efficient loading of neutral atoms into a magnetic waveguide produced by the magnetic fields of microfabricated current-carrying conductors. The lithographically patterned conductors on this ``atom chip'' can be used to make a variety of guiding and trapping structures for manipulating cold atoms and Bose-Einstein condensates. A three-chamber vacuum apparatus collects atoms in a magneto-optical trap, precools them via evaporative cooling, and delivers them to the final chamber containing the atom chip. We describe in detail how the precooled atomic cloud is transferred from a macroscopic magnetic Ioffe-Pritchard trap to the microscopic magnetic waveguide on the atom chip 21cm21\phantom{\rule{0.3em}{0ex}}\mathrm{cm}21cm away. Permanent magnets provide a confining two-dimensional quadrupole field to guide the atoms between the two chambers while longitudinally the cloud is allowed to freely expand during the transfer. Strategically placed coils are used to control the longitudinal size and speed of the atomic cloud as it is loaded on the atom chip.
Abstract Here we report of a design and the performance of an optimized micro-fabricated conveyor belt for precise and adiabatic transportation of cold atoms. A theoretical model is presented to determine optimal currents in conductors used for the transportation. We experimentally demonstrate a fast adiabatic transportation of Rubidium (87Rb) cold atoms with minimal loss and heating with as few as three conveyor belt conductors. This novel design of a multilayered conveyor belt structure is fabricated in aluminium nitride (AlN) because of its outstanding thermal and electrical properties. This demonstration would pave a way for a compact and portable quantum device required for quantum information processing and sensors, where precise positioning of cold atoms is desirable.
Ultracold atomic gases can be utilised as extremely sensitive probes of their surrounding environment. In particular, samples of ultracold atoms confined using chip-based microtraps are an ideal tool for mapping electric and magnetic field landscapes. Over the course of this thesis, a new experiment capable of performing surface microscopy using magnetically trapped clouds of cold rubidium-87 atoms has been built. The focus of the work is on the design and construction of the experimental system, which must incorporate many different aspects for manipulating thermal atomic gases, with a view to positioning them at sub-micron distances from special surfaces. This reduced atom-surface separation is necessary for implementing a high resolution, high sensitivity magnetic field sensor with cold atoms. Although current microfabrication techniques easily enable trapping at distances on the order of micrometres, several distance-dependent surface effects - such as the Casimir-Polder force, Johnson-Nyquist noise, and stray potentials - eventually impede magnetic trapping at the sub-micron level. These surface effects can greatly modify the confining potentials, which reduces the trap depth and consequently leads to an additional loss rate of atoms from the trap. We have explored the possibility of using special surfaces such as nano-membranes of silicon nitride and graphene, which have reduced atom- surface interactions, to enable trapping distances at the sub-micron level. A multilayer printed circuit board chip has been designed to form an initial magnetic trap and then transport the cloud of atoms to a desired location over the samples. This chip, along with various samples, is mounted on a custom-made electrical feedthrough designed to make connections to all conductor that are inside the vacuum chamber. The initial cloud of cold atoms can then be prepared in the central region of the chip and delivered to the location of the samples on either side. The experimental system is able to routinely capture over 10^8 rubidium-87 atoms at a temperature of 80 micro-Kelvin in a magneto-optical trap using a novel scheme of five laser beams. A method is demonstrated for enhancing the atom number in the magneto-optical traps by a factor of two by using laser beams with two slightly different frequencies. Atoms from the magneto-optical trap are then transferred to a purely magnetic trap formed by the wires on the printed circuit board chip. Time-dependent currents in the chip wires then create a dynamic potential, which is shown to successfully transport the atomic sample over a distance of 12 millimetre with minimal atom loss. This thesis describes the development of the apparatus in detail, along with careful characterisation of the cold cloud at various stages of the experimental sequence. Initial results on the long distance atom transport are presented. Finally, the experimental results of the two frequency magneto-optical trap for atom number improvement are discussed.