Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:cond-mat/0601522 · Physical Review B

Decoherence processes in a current biased dc SQUID

Julien Claudon, Aurélien Fay, Laurent-Patrick Lévy, O. Buisson

Published May 5, 2006• 20 citations
arXivHTMLPDF

Abstract

A current biased dc superconducting quantum interference device behaves as an anharmonic quantum oscillator controlled by a bias current and an applied magnetic flux. We consider here its two level limit consisting of the two lower energy states \ensuremath{\mid}0⟩ and \ensuremath{\mid}1⟩. We have measured energy relaxation times and microwave absorption for different bias currents and fluxes in the low microwave power limit. Decoherence times are extracted. The low frequency flux and current noise have been measured independently by analyzing the probability of current switching from the superconducting to the finite voltage state, as a function of applied flux. The high frequency part of the current noise is derived from the electromagnetic environment of the circuit. The decoherence of this quantum circuit can be fully accounted for by these current and flux noise sources.

DOI
10.1103/physrevb.73.180502

Related papers

Relaxation and Dephasing in a Flux-qubit

Patrice Bertet, I. Chiorescu, Guido Burkard +4 more

We report detailed measurements of the relaxation and dephasing time in a flux-qubit measured by a switching DC SQUID. We studied their dependence on the two important circuit bias parameters: the externally applied magnetic flux and the bias current through the SQUID in two samples. We demonstrate two complementary strategies to protect the qubit from these decoherence sources. One consists in biasing the qubit so that its resonance frequency is stationary with respect to the control parameters ({\it optimal point}) ; the second consists in {\it decoupling} the qubit from current noise by chosing a proper bias current through the SQUID. At the decoupled optimal point, we measured long spin-echo decay times of up to $4 μs$.

arXiv:cond-mat/0412485•Dec 17, 2004•30 citations

Coherent Oscillations in a Superconducting Multilevel Quantum System

Julien Claudon, Franck Balestro, F. W. J. Hekking +1 more

We have observed coherent oscillations in a multilevel quantum system, formed by a current-biased dc SQUID. These oscillations have been induced by applying resonant microwave pulses of flux. Quantum measurement is performed by a nanosecond flux pulse that projects the final state onto one of two different voltage states of the dc SQUID, which can be read out. The number of quantum states involved in the coherent oscillations increases with increasing microwave power. The dependence of the oscillation frequency on microwave power deviates strongly from the linear regime expected for a two-level system and can be very well explained by a theoretical model taking into account the anharmonicity of the multilevel system.

arXiv:cond-mat/0405430•Physical Review Letters•Oct 26, 2004•111 citations

Nanosecond quantum state detection in a current-biased dc SQUID

Julien Claudon, Aurélien Fay, Emile Hoskinson +1 more

This paper presents our procedure to measure the quantum state of a dc superconducting quantum interference device (SQUID) within a few nanoseconds, using an adiabatic dc flux pulse. Detection of the ground state is governed by standard macroscopic quantum tunneling (MQT) theory, with a small correction due to residual noise in the bias current. In the two-level limit, where the SQUID constitutes a phase qubit, an observed contrast of 0.54 indicates a significant loss in contrast compared to the MQT prediction. It is attributed to spurious depolarization (loss of excited state occupancy) during the leading edge of the adiabatic flux measurement pulse. We give a simple phenomenological relaxation model which is able to predict the observed contrast of multilevel Rabi oscillations for various microwave amplitudes.

arXiv:cond-mat/0702453•Physical Review B•Jul 13, 2007•18 citations

Superconducting quantum interference device with frequency-dependent damping: Readout of flux qubits

Timothy L. Robertson, B. L. T. Plourde, T. Hime +4 more

Recent experiments on superconducting flux qubits, consisting of a superconducting loop interrupted by Josephson junctions, have demonstrated quantum coherence between two different quantum states. The state of the qubit is measured with a superconducting quantum interference device (SQUID). Such measurements require the SQUID to have high resolution while exerting minimal backaction on the qubit. By designing shunts across the SQUID junctions appropriately, one can improve the measurement resolution without increasing the backaction significantly. Using a path-integral approach to analyze the Caldeira-Leggett model, we calculate the narrowing of the distribution of the switching events from the zero-voltage state of the SQUID for arbitrary shunt admittances, focusing on shunts consisting of a capacitance ${C}_{s}$ and resistance ${R}_{s}$ in series. To test this model, we fabricated a dc SQUID in which each junction is shunted with a thin-film interdigitated capacitor in series with a resistor, and measured the switching distribution as a function of temperature and applied magnetic flux. After accounting for the damping due to the SQUID leads, we found good agreement between the measured escape rates and the predictions of our model. We analyze the backaction of a shunted symmetric SQUID on a flux qubit. For the given parameters of our SQUID and realistic parameters for a flux qubit, at the degeneracy point we find a relaxation time of $113\phantom{\rule{0.3em}{0ex}}\ensuremath{\mu}\mathrm{s}$, which limits the decoherence time to $226\phantom{\rule{0.3em}{0ex}}\ensuremath{\mu}\mathrm{s}$. Based on our analysis of the escape process, we determine that a SQUID with purely capacitive shunts should have narrow switching distributions and no dissipation.

Physical Review B•Jul 11, 2005•23 citations

Flicker (1∕f) noise in the critical current of Josephson junctions at 0.09–4.2K

F. C. Wellstood, C. Urbina, John L. Clarke

We have measured the low-frequency noise in the critical current Ic of six dc superconducting quantum interference devices (SQUIDs) with resistively shunted Nb–NbOx–PbIn Josephson junctions in the temperature range T=0.09–4.2K. Each device is voltage biased, the applied flux is an integer number of flux quanta, and the current fluctuations are measured with a second dc SQUID. At low frequencies f, there is a component of the power spectrum of the critical current fluctuations given approximately by SIc(f)=CIc2T2∕Af, where A is the area of both junctions, and C≈(3.9±0.4)×10−23m2∕K2. For quantum bits based on Josephson junctions, the scaling of SIc(f) with T2 implies that the dephasing time limited by critical current l∕f noise should scale as 1∕T for temperatures down to at least 0.09K.

Applied Physics Letters•Nov 29, 2004•62 citations

Reducing decoherence in dc SQUID phase qubits

Anthony Przybysz

This thesis examines sources of dissipation and dephasing in a dc SQUID phase qubit. Coupling of the qubit to the bias lines and lossy dielectrics causes the qubit to lose quantum information through a process known generally as decoherence. Using knowledge of the possible sources of decoherence, a dc SQUID phase qubit is designed with parameters that should have made it resistant to dissipation and dephasing from those sources. Device PB9 was a dc SQUID with one small area 0.23 (μm)2 Josephson junction with a critical current of 130 nA, which was meant to be the qubit junction, and a larger area 5 (μm)2 junction with a critical current of 8.6 μA, which acted as part of an inductive isolation network. The qubit junction was shunted by a 1.5 pF low-loss interdigitated capacitor. The dc current bias line had an on-chip LC filter with a cutoff frequency of 180 MHz. The other control lines were also designed to minimize coupling of dissipative elements to the qubit. According to a theoretical model of the dissipation and dephasing, the qubit was expected to have an energy relaxation T1 ≤ 8.4 μs and dephasing time Tø ∼ 1 μs. Because of the relatively high Josephson inductance of the qubit junction, the device did not act perform like a conventional isolated single-junction phase qubit. Instead, the resonant modes that I observed were the normal modes of the entire SQUID. At 20 mK and a frequency of 4.047 GHz, the maximum energy relaxation time of the device was found to be 350 ± 70 ns, despite the optimized design. Through a study of T1 versus applied flux, T1 was found to depend on the strength of the coupling of the microwave drive line to the qubit. When the line was more coupled, T1 was shorter. This was evidence that the microwave line was overcoupled to the qubit, and was limiting the lifetime of the excited state T1. Through a study of the spectroscopic coherence time T2* , which measured the effects of low-frequency inhomogeneous broadening and higher frequency dephasing from noise, I discovered that device PB9 has several sweet spots. In particular, the presence of a sweet spot with respect to critical current fluctuations allowed me to identify critical current noise as a major source of broadening and dephasing in the qubit. From the spectroscopy I estimated the 1/f critical current noise power density at 1 Hz was SI01 (1Hz) ≈ 10 (nA) 2/Hz and the 1/f flux noise power spectral density at 1 Hz was SΦ (1Hz) ≈ (110 μΦ 0)2/Hz. Both of these values were quite high, possibly due to switching of the device between measurements.

•Jan 1, 2010•1 citation
A current biased dc superconducting quantum interference device behaves as an anharmonic quantum oscillator controlled by a bias current and an applied magnetic flux. We consider here its two level limit consisting of the two lower energy states \ensuremath{\mid}0⟩ and \ensuremath{\mid}1⟩. We have measured energy relaxation times and microwave absorption for different bias currents and fluxes in the low microwave power limit. Decoherence times are extracted. The low frequency flux and current noise have been measured independently by analyzing the probability of current switching from the superconducting to the finite voltage state, as a function of applied flux. The high frequency part of the current noise is derived from the electromagnetic environment of the circuit. The decoherence of this quantum circuit can be fully accounted for by these current and flux noise sources.
We report detailed measurements of the relaxation and dephasing time in a flux-qubit measured by a switching DC SQUID. We studied their dependence on the two important circuit bias parameters: the externally applied magnetic flux and the bias current through the SQUID in two samples. We demonstrate two complementary strategies to protect the qubit from these decoherence sources. One consists in biasing the qubit so that its resonance frequency is stationary with respect to the control parameters ({\it optimal point}) ; the second consists in {\it decoupling} the qubit from current noise by chosing a proper bias current through the SQUID. At the decoupled optimal point, we measured long spin-echo decay times of up to 4μs4 μs4μs.
We have observed coherent oscillations in a multilevel quantum system, formed by a current-biased dc SQUID. These oscillations have been induced by applying resonant microwave pulses of flux. Quantum measurement is performed by a nanosecond flux pulse that projects the final state onto one of two different voltage states of the dc SQUID, which can be read out. The number of quantum states involved in the coherent oscillations increases with increasing microwave power. The dependence of the oscillation frequency on microwave power deviates strongly from the linear regime expected for a two-level system and can be very well explained by a theoretical model taking into account the anharmonicity of the multilevel system.
This paper presents our procedure to measure the quantum state of a dc superconducting quantum interference device (SQUID) within a few nanoseconds, using an adiabatic dc flux pulse. Detection of the ground state is governed by standard macroscopic quantum tunneling (MQT) theory, with a small correction due to residual noise in the bias current. In the two-level limit, where the SQUID constitutes a phase qubit, an observed contrast of 0.54 indicates a significant loss in contrast compared to the MQT prediction. It is attributed to spurious depolarization (loss of excited state occupancy) during the leading edge of the adiabatic flux measurement pulse. We give a simple phenomenological relaxation model which is able to predict the observed contrast of multilevel Rabi oscillations for various microwave amplitudes.
Recent experiments on superconducting flux qubits, consisting of a superconducting loop interrupted by Josephson junctions, have demonstrated quantum coherence between two different quantum states. The state of the qubit is measured with a superconducting quantum interference device (SQUID). Such measurements require the SQUID to have high resolution while exerting minimal backaction on the qubit. By designing shunts across the SQUID junctions appropriately, one can improve the measurement resolution without increasing the backaction significantly. Using a path-integral approach to analyze the Caldeira-Leggett model, we calculate the narrowing of the distribution of the switching events from the zero-voltage state of the SQUID for arbitrary shunt admittances, focusing on shunts consisting of a capacitance Cs{C}_{s}Cs​ and resistance Rs{R}_{s}Rs​ in series. To test this model, we fabricated a dc SQUID in which each junction is shunted with a thin-film interdigitated capacitor in series with a resistor, and measured the switching distribution as a function of temperature and applied magnetic flux. After accounting for the damping due to the SQUID leads, we found good agreement between the measured escape rates and the predictions of our model. We analyze the backaction of a shunted symmetric SQUID on a flux qubit. For the given parameters of our SQUID and realistic parameters for a flux qubit, at the degeneracy point we find a relaxation time of $113\phantom{\rule{0.3em}{0ex}}\ensuremath{\mu}\mathrm{s}$, which limits the decoherence time to $226\phantom{\rule{0.3em}{0ex}}\ensuremath{\mu}\mathrm{s}$. Based on our analysis of the escape process, we determine that a SQUID with purely capacitive shunts should have narrow switching distributions and no dissipation.
We have measured the low-frequency noise in the critical current Ic of six dc superconducting quantum interference devices (SQUIDs) with resistively shunted Nb–NbOx–PbIn Josephson junctions in the temperature range T=0.09–4.2K. Each device is voltage biased, the applied flux is an integer number of flux quanta, and the current fluctuations are measured with a second dc SQUID. At low frequencies f, there is a component of the power spectrum of the critical current fluctuations given approximately by SIc(f)=CIc2T2∕Af, where A is the area of both junctions, and C≈(3.9±0.4)×10−23m2∕K2. For quantum bits based on Josephson junctions, the scaling of SIc(f) with T2 implies that the dephasing time limited by critical current l∕f noise should scale as 1∕T for temperatures down to at least 0.09K.
This thesis examines sources of dissipation and dephasing in a dc SQUID phase qubit. Coupling of the qubit to the bias lines and lossy dielectrics causes the qubit to lose quantum information through a process known generally as decoherence. Using knowledge of the possible sources of decoherence, a dc SQUID phase qubit is designed with parameters that should have made it resistant to dissipation and dephasing from those sources. Device PB9 was a dc SQUID with one small area 0.23 (μm)2 Josephson junction with a critical current of 130 nA, which was meant to be the qubit junction, and a larger area 5 (μm)2 junction with a critical current of 8.6 μA, which acted as part of an inductive isolation network. The qubit junction was shunted by a 1.5 pF low-loss interdigitated capacitor. The dc current bias line had an on-chip LC filter with a cutoff frequency of 180 MHz. The other control lines were also designed to minimize coupling of dissipative elements to the qubit. According to a theoretical model of the dissipation and dephasing, the qubit was expected to have an energy relaxation T1 ≤ 8.4 μs and dephasing time Tø ∼ 1 μs. Because of the relatively high Josephson inductance of the qubit junction, the device did not act perform like a conventional isolated single-junction phase qubit. Instead, the resonant modes that I observed were the normal modes of the entire SQUID. At 20 mK and a frequency of 4.047 GHz, the maximum energy relaxation time of the device was found to be 350 ± 70 ns, despite the optimized design. Through a study of T1 versus applied flux, T1 was found to depend on the strength of the coupling of the microwave drive line to the qubit. When the line was more coupled, T1 was shorter. This was evidence that the microwave line was overcoupled to the qubit, and was limiting the lifetime of the excited state T1. Through a study of the spectroscopic coherence time T2* , which measured the effects of low-frequency inhomogeneous broadening and higher frequency dephasing from noise, I discovered that device PB9 has several sweet spots. In particular, the presence of a sweet spot with respect to critical current fluctuations allowed me to identify critical current noise as a major source of broadening and dephasing in the qubit. From the spectroscopy I estimated the 1/f critical current noise power density at 1 Hz was SI01 (1Hz) ≈ 10 (nA) 2/Hz and the 1/f flux noise power spectral density at 1 Hz was SΦ (1Hz) ≈ (110 μΦ 0)2/Hz. Both of these values were quite high, possibly due to switching of the device between measurements.