Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:cond-mat/0311332 · Applied Physics Letters

Circuit with small-capacitance high-quality Nb Josephson junctions

道生 渡部, Yasunobu Nakamura, Jaw-Shen Tsai

Published Jan 13, 2004• 24 citations
arXivHTMLPDF

Abstract

We have developed a fabrication process for nanoscale tunnel junctions which includes focused-ion-beam etching from different directions. By applying the process to a Nb/(Al–)Al2O3/Nb trilayer, we have fabricated a Nb single-electron transistor (SET), and characterized the SET at low temperatures, T=0.04–40 K. The superconducting gap energy and the transition temperature of the Nb SET agree with the bulk values, which suggests high quality Nb junctions. The single-electron charging energy of the SET is estimated to be larger than 1 K.

DOI
10.1063/1.1640798

Related papers

Transport properties of nanoscale Nb and NbN Josephson junctions fabricated by focused-ion-beam milling

Kazuaki Matsuba, 道生 渡部, Jaw-Shen Tsai

We have studied low-temperature electrical transport properties of nanoscale Nb∕(Al–)Al2O3∕Nb and NbN∕AlN∕NbN Josephson junctions (JJs) fabricated by focused-ion-beam (FIB) milling. This FIB fabrication process yields high-quality JJs whose superconducting gap energy agrees with the bulk value. In this paper, we report the improvement in the precision of the fabrication technology by employing a weaker ion beam current and by introducing a step of XeF2-gas-assisted milling, which allowed us to reduce the anodization voltage. For Nb JJs, we measured the current-voltage (I-V) characteristics of single-electron transistors (SETs) and examined the current observed within the superconducting energy gap. At finite voltages, we observed current peaks due to the Josephson-quasiparticle (JQP) cycle. Based on the JQP-peak positions, we estimated the charging energy Ec of the SETs. For all SETs, Ec∕kB is larger than 1K, which is consistent with 0.1×0.1μm2 junctions. We also analyzed the superconducting critical current at zero voltage. The ratio Ic∕Ic0 depended on the junction size, where Ic is the measured critical current and Ic0 is the theoretical one. The I-V curves of NbN single Josephson junctions also depended on the junction size, and they were qualitatively different, especially around the energy gap. We will discuss the possible origins for the junction-size dependence.

Journal of Applied Physics•Apr 1, 2008•2 citations

Single-charge devices with ultrasmall Nb∕AlOx∕Nb trilayer Josephson junctions

R. Dolata, Hansjorg Scherer, Alexander B Zorin +1 more

Josephson junction transistors and 50-junction arrays with linear junction dimensions from 200nm down to 70nm were fabricated from standard Nb∕AlOx∕Nb trilayers. The fabrication process includes electron beam lithography, dry etching, anodization, and planarization by chemical-mechanical polishing. The samples were characterized at temperatures down to 25mK. In general, all junctions are of high quality and their I-U characteristics show low leakage currents and high superconducting energy gap values of Δ≈1.35meV. The characteristics of the transistors and arrays exhibit some features in the subgap area, associated with tunneling of Cooper pairs, quasiparticles, and their combinations due to the redistribution of the bias voltage between the junctions. Total island capacitances of the transistor samples ranged from 1.5fF to 4fF, depending on the junction sizes. Devices made of junctions with linear dimensions below 100nm×100nm demonstrate a remarkable single-electron behavior in both superconducting and normal state. We also investigated the area dependence of the junction capacitances for transistor and array samples.

arXiv:cond-mat/0410288•Journal of Applied Physics•Feb 4, 2005•44 citations

TECHNOLOGIES FOR THE FABRICATION OF NANOSCALE SUPERCONDUCTING CIRCUITS

道生 渡部

Researches on the fabrication of ~ 0.1 × 0.1 μ m 2 superconductor–insulator–superconductor (SIS) Josephson junctions are reviewed. Today, a typical dimension is 1–10 μm for Josephson junctions in superconducting integrated circuits. These Josephson junctions are defined by well-established photolithographic technology with reactive ion etching (RIE), and for the superconductor, Nb is almost always used. The merits of Nb include the facts that the superconducting transition temperature Tc of Nb (9.2 K ) is higher than the boiling point of He (4.2 K ), and that Nb has excellent stability against thermal cycling between room temperature and liquid- He temperature. For the fabrication of ~ 0.1 × 0.1 μ m 2 junctions, on the other hand, there is a standard process with electron-beam lithography, shadow evaporation, and lift-off. This process works well for Al (Tc = 1.2 K ), however, it is not ideal for Nb . The scope of this brief review is the nanoscale junction with Nb electrodes. We will look at the efforts of optimizing the standard lift-off process for Nb , electron-beam-lithographic versions of the Nb Josephson-junction technology, focused-ion-beam (FIB) etching as a convenient alternative to electron-beam lithography and RIE, etc. In order to characterize nanoscale tunnel junctions, the single-charge transistor has been often fabricated. Therefore, a summary of its theoretical transport properties is also included.

Modern Physics Letters B•Apr 30, 2005•3 citations

Fabrication of high-quality submicron Nb/Al-AlO x /Nb tunnel junctions

Haifeng Yu, Cao Wen-Hui, Zhu Xiao-Bo +6 more

Nb/Al–AlO x /Nb tunnel junctions are often used in the studies of macroscopic quantum phenomena and superconducting qubit applications of the Josephson devices. In this work, we describe a convenient and reliable process using electron beam lithography for the fabrication of high-quality, submicron-sized Nb/Al–AlO x /Nb Josephson junctions. The technique follows the well-known selective Nb etching process and produces high-quality junctions with V m = 100 mV at 2.3 K for the typical critical current density of 2.2 kA/cm 2 , which can be adjusted by controlling the oxygen pressure and oxidation time during the formation of the tunnelling barrier. We present the results of the temperature dependence of the sub-gap current and in-plane magnetic-field dependence of the critical current, and compare them with the theoretical predictions.

Chinese Physics B•Aug 1, 2008•7 citations

Anodization-free fabrication process for high-quality cross-type Josephson tunnel junctions based on a Nb/Al-AlO x /Nb trilayer

F Adam, C. Enss, Sebastian Kempf

Abstract Josephson tunnel junctions form the basis for various superconductor electronic devices. For this reason, enormous efforts are routinely taken to establish and later on maintain a scalable and reproducible wafer-scale manufacturing process for high-quality Josephson junctions. Here, we present an anodization-free fabrication process for Nb/Al-AlO x /Nb cross-type Josephson junctions that requires only a small number of process steps and that is in general intrinsically compatible with wafer-scale fabrication. We show that the fabricated junctions are of very high quality and, compared to other junction types, exhibit not only a significantly reduced capacitance but also an almost rectangular critical current density profile. Our process hence enables the usage of low capacitance Josephson junctions for superconductor electronic devices such as ultra-low noise dc-superconducting quantum interference devices (SQUIDs), microwave SQUID multiplexers based on non-hysteretic rf-SQUIDs and RFSQ circuits.

arXiv:2403.01806•Superconductor Science and Technology•Jul 8, 2024•6 citations

Fabrication of ultrasmall Nb-AlOx-Nb Josephson tunnel junctions

John M. Martinis, Ronald H. Ono

We describe a fabrication process to make Nb-AlOx-Nb edge junctions with areas as small as 0.0022 μm2 and with current densities from 10 to 24 000 A/cm2. The junction conductance was low for voltages below the superconducting energy gap which indicates good quality tunnel barriers. Coulomb gap measurements obtained when the junctions were in the normal state were used to find the junction capacitance. Junction capacitance as small as 0.18 fF has been measured.

Applied Physics Letters•Aug 6, 1990•34 citations
We have developed a fabrication process for nanoscale tunnel junctions which includes focused-ion-beam etching from different directions. By applying the process to a Nb/(Al–)Al2O3/Nb trilayer, we have fabricated a Nb single-electron transistor (SET), and characterized the SET at low temperatures, T=0.04–40 K. The superconducting gap energy and the transition temperature of the Nb SET agree with the bulk values, which suggests high quality Nb junctions. The single-electron charging energy of the SET is estimated to be larger than 1 K.
We have studied low-temperature electrical transport properties of nanoscale Nb∕(Al–)Al2O3∕Nb and NbN∕AlN∕NbN Josephson junctions (JJs) fabricated by focused-ion-beam (FIB) milling. This FIB fabrication process yields high-quality JJs whose superconducting gap energy agrees with the bulk value. In this paper, we report the improvement in the precision of the fabrication technology by employing a weaker ion beam current and by introducing a step of XeF2-gas-assisted milling, which allowed us to reduce the anodization voltage. For Nb JJs, we measured the current-voltage (I-V) characteristics of single-electron transistors (SETs) and examined the current observed within the superconducting energy gap. At finite voltages, we observed current peaks due to the Josephson-quasiparticle (JQP) cycle. Based on the JQP-peak positions, we estimated the charging energy Ec of the SETs. For all SETs, Ec∕kB is larger than 1K, which is consistent with 0.1×0.1μm2 junctions. We also analyzed the superconducting critical current at zero voltage. The ratio Ic∕Ic0 depended on the junction size, where Ic is the measured critical current and Ic0 is the theoretical one. The I-V curves of NbN single Josephson junctions also depended on the junction size, and they were qualitatively different, especially around the energy gap. We will discuss the possible origins for the junction-size dependence.
Josephson junction transistors and 50-junction arrays with linear junction dimensions from 200nm down to 70nm were fabricated from standard Nb∕AlOx∕Nb trilayers. The fabrication process includes electron beam lithography, dry etching, anodization, and planarization by chemical-mechanical polishing. The samples were characterized at temperatures down to 25mK. In general, all junctions are of high quality and their I-U characteristics show low leakage currents and high superconducting energy gap values of Δ≈1.35meV. The characteristics of the transistors and arrays exhibit some features in the subgap area, associated with tunneling of Cooper pairs, quasiparticles, and their combinations due to the redistribution of the bias voltage between the junctions. Total island capacitances of the transistor samples ranged from 1.5fF to 4fF, depending on the junction sizes. Devices made of junctions with linear dimensions below 100nm×100nm demonstrate a remarkable single-electron behavior in both superconducting and normal state. We also investigated the area dependence of the junction capacitances for transistor and array samples.
Researches on the fabrication of ~ 0.1 × 0.1 μ m 2 superconductor–insulator–superconductor (SIS) Josephson junctions are reviewed. Today, a typical dimension is 1–10 μm for Josephson junctions in superconducting integrated circuits. These Josephson junctions are defined by well-established photolithographic technology with reactive ion etching (RIE), and for the superconductor, Nb is almost always used. The merits of Nb include the facts that the superconducting transition temperature Tc of Nb (9.2 K ) is higher than the boiling point of He (4.2 K ), and that Nb has excellent stability against thermal cycling between room temperature and liquid- He temperature. For the fabrication of ~ 0.1 × 0.1 μ m 2 junctions, on the other hand, there is a standard process with electron-beam lithography, shadow evaporation, and lift-off. This process works well for Al (Tc = 1.2 K ), however, it is not ideal for Nb . The scope of this brief review is the nanoscale junction with Nb electrodes. We will look at the efforts of optimizing the standard lift-off process for Nb , electron-beam-lithographic versions of the Nb Josephson-junction technology, focused-ion-beam (FIB) etching as a convenient alternative to electron-beam lithography and RIE, etc. In order to characterize nanoscale tunnel junctions, the single-charge transistor has been often fabricated. Therefore, a summary of its theoretical transport properties is also included.
Nb/Al–AlO x /Nb tunnel junctions are often used in the studies of macroscopic quantum phenomena and superconducting qubit applications of the Josephson devices. In this work, we describe a convenient and reliable process using electron beam lithography for the fabrication of high-quality, submicron-sized Nb/Al–AlO x /Nb Josephson junctions. The technique follows the well-known selective Nb etching process and produces high-quality junctions with V m = 100 mV at 2.3 K for the typical critical current density of 2.2 kA/cm 2 , which can be adjusted by controlling the oxygen pressure and oxidation time during the formation of the tunnelling barrier. We present the results of the temperature dependence of the sub-gap current and in-plane magnetic-field dependence of the critical current, and compare them with the theoretical predictions.
Abstract Josephson tunnel junctions form the basis for various superconductor electronic devices. For this reason, enormous efforts are routinely taken to establish and later on maintain a scalable and reproducible wafer-scale manufacturing process for high-quality Josephson junctions. Here, we present an anodization-free fabrication process for Nb/Al-AlO x /Nb cross-type Josephson junctions that requires only a small number of process steps and that is in general intrinsically compatible with wafer-scale fabrication. We show that the fabricated junctions are of very high quality and, compared to other junction types, exhibit not only a significantly reduced capacitance but also an almost rectangular critical current density profile. Our process hence enables the usage of low capacitance Josephson junctions for superconductor electronic devices such as ultra-low noise dc-superconducting quantum interference devices (SQUIDs), microwave SQUID multiplexers based on non-hysteretic rf-SQUIDs and RFSQ circuits.