Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Acta Physica Sinica

A semiconductor nanocrystal PbSe quantum dot fiber amplifier

Cheng Cheng, Zhang Hang, 浙江工业大学应用物理系,杭州 310023

Published Jan 1, 2006• 14 citations
Publisher

Abstract

A novel kind of fiber amplifier——quantum dot doped fiber amplifier (QDFA) is presented. Using semiconductor nanocrystal PbSe as a dopant, the gain bandwidths of the PbSe-QDFA are simulated by solving the rate equation and the light propagation equation in a two-level system, applying a genetic algorithm combined with an “inversing method”. Comparing with conventional erbium-doped fiber amplifiers available, there is evidence to show that characteristics of the PbSe-QDFA are obviously advantageous in respect of bandwidth and noise, especially on long-waelength band. Furthermore, the ideal emission-absorption cross-sections of the quantum dot are determined by utilizing the genetic algorithm. Under such ideal cross-sections, the QDFA possesses with the performance of ultra-bandwidth and low noise figure near a quantum limit.

DOI
10.7498/aps.55.4139

Related papers

A Multiquantum-Dot-Doped Fiber Amplifier With Characteristics of Broadband, Flat Gain, and Low Noise

Cheng Cheng

Doped with PbSe nanocrystals of different sizes, a multiquantum-dot-doped fiber amplifier (MQDFA) is proposed. Performance of the MQDFA is simulated by solving light-propagation equations and rate equations for a three-level system, and by applying superposed emission-absorption cross sections of the quantum dots (QDs). Pumped with 980 nm, this proposed MQDFA has characteristics of broader band, flatter gain, and lower noise than those of the erbium-doped fiber amplifiers at present. There is evidence to show that two factors, i.e., the equivalent Stokes shifts and the full wave at half maximum of the superposed spectra, dominate the performances of the MQDFA. Also, the equivalent Stokes shift and the FWHM are tunable by adopting the QDs in different sizes and choosing the doped number available. It is expected that such a MQDFA may be able to cover the all waveband in telecommunications if it is optimized on the doped number, sizes, and doped concentrations of the QDs.

Journal of Lightwave Technology•Jun 1, 2008•41 citations

Optimization of bismuth-doped fiber amplifier gain spectrum based on genetic algorithm in 1200 nm-1600 nm

Zuohao Guo, Chenyu Xu, Jialing Yao

Abstract With the continuous evolution of communication technology, and the rapid rise of fiber optic communication in China However, the transmission distance of fiber optic communication is limited due to its fiber loss, so fiber optic amplifier has become one of the key research topics today. Currently on the market is a large-scale commercial bait-doped fiber amplifier, although it has the advantage of low noise and high gain, its effective amplification band is only concentrated in 1530 nm-1620 nm, however, there are many important transmission band amplification there are still research gaps. As a result, the focus of this paper’s research is on optimizing the gain spectrum of a bismuth-doped fiber amplifier at wavelengths between 1200 and 1600 nm using modelling and numerical simulation. The research method of this paper is as follows: first of all, after the literature survey, this topic is using the three-energy level structure, and then collecting the data of pump light wavelength and emission absorption cross-section, signal light emission, and absorption cross-section. fit the data to the graph line, and call the genetic optimization algorithm to derive the gain spectrum optimal value. It’s found that when the pump light wavelength is 1230 nm, fiber length is 2 m, bismuth ion doping concentration is 10.0×1024 ions/m3, the signal light wavelength is 1330 m, its amplifier gain spectrum reaches a peak of 57.17 dB, which is consistent with the results of the three-layer cycle (manual search).

Journal of Physics Conference Series•Nov 1, 2023•0 citations

Characteristics of bandwidth, gain and noise of a PbSe quantum dot-doped fiber amplifier

Cheng Cheng, Hang Zhang

Optics Communications•Jun 14, 2007•40 citations

The Gain Characteristics and the Optimum Fiber Length of Erbium-doped Fiber Amplifiers

Huang De, Li Zai

An apporoximative theoretical of an erbium-doped fiber amplifier (EDFA) has been proposed in this paper by the rate equation of three-level system. The optimum fiber length is obtained with different pump wavelength by considering the excited-stated-absorption(ESA) in EDFA. The relations between the gain and signal light intensity and pump light intensity are analyzed. It is found that the gain spectrum shape can be changed with the fiber length, which provides the evidence that EDFA is of great potential use in wavelength division multiplexed telecommunication systems.

Optical Communication Technology•Jan 1, 1994•0 citations

Modeling a Broadband Bismuth-Doped Fiber Amplifier

Chun Jiang

In this paper, we present the energy level, transition configuration, and numerical model of a bismuth-doped fiber amplifier for the first time, to the best of authorspsila knowledge. With a three-level system, the rate and power propagation equations of the model are solved to examine the effect of the fiber parameter and pump power on the bandwidth of the gain spectra. It can be predicted that when excited at wavelength in the 800-900 nm range, the amplifier can have a ultrabroad gain spectra in the 1.2-1.62 mum range, which cover the low-loss windows of the all-wave fiber.

IEEE Journal of Selected Topics in Quantum Electronics•Jan 1, 2009•28 citations

Cross gain modulation in quantum dot semiconductor optical amplifiers under the influence of the Probe

Ahmed H. Flayyih, Seyedeh Hamideh Kazemi, Amin Habbeb AL-Khursan

The Pulse effect on the cross-gain modulation (XGM) in the quantum dot (QD) semiconductor optical amplifiers (SOAs) is investigated using the combining of the SOA power with the QD rate equations system. The QDs structure includes three regions: ground state (GS), excited state (ES) and wetting layer (WL). Thus, a set of rate equations for pump and probe signals is introduced for both steady-state and small-signal power values, which are solved numerically. The pulse shape was included in the analysis, for pump and probe signals. The theoretical results showed a good agreement with the experimental results. It was found that decreasing pulse width of pump/probe ratio is efficient to increase XGM efficiency and bandwidth.

University of Thi-Qar Journal of Science•Dec 26, 2023•0 citations
A novel kind of fiber amplifier——quantum dot doped fiber amplifier (QDFA) is presented. Using semiconductor nanocrystal PbSe as a dopant, the gain bandwidths of the PbSe-QDFA are simulated by solving the rate equation and the light propagation equation in a two-level system, applying a genetic algorithm combined with an “inversing method”. Comparing with conventional erbium-doped fiber amplifiers available, there is evidence to show that characteristics of the PbSe-QDFA are obviously advantageous in respect of bandwidth and noise, especially on long-waelength band. Furthermore, the ideal emission-absorption cross-sections of the quantum dot are determined by utilizing the genetic algorithm. Under such ideal cross-sections, the QDFA possesses with the performance of ultra-bandwidth and low noise figure near a quantum limit.
Doped with PbSe nanocrystals of different sizes, a multiquantum-dot-doped fiber amplifier (MQDFA) is proposed. Performance of the MQDFA is simulated by solving light-propagation equations and rate equations for a three-level system, and by applying superposed emission-absorption cross sections of the quantum dots (QDs). Pumped with 980 nm, this proposed MQDFA has characteristics of broader band, flatter gain, and lower noise than those of the erbium-doped fiber amplifiers at present. There is evidence to show that two factors, i.e., the equivalent Stokes shifts and the full wave at half maximum of the superposed spectra, dominate the performances of the MQDFA. Also, the equivalent Stokes shift and the FWHM are tunable by adopting the QDs in different sizes and choosing the doped number available. It is expected that such a MQDFA may be able to cover the all waveband in telecommunications if it is optimized on the doped number, sizes, and doped concentrations of the QDs.
Abstract With the continuous evolution of communication technology, and the rapid rise of fiber optic communication in China However, the transmission distance of fiber optic communication is limited due to its fiber loss, so fiber optic amplifier has become one of the key research topics today. Currently on the market is a large-scale commercial bait-doped fiber amplifier, although it has the advantage of low noise and high gain, its effective amplification band is only concentrated in 1530 nm-1620 nm, however, there are many important transmission band amplification there are still research gaps. As a result, the focus of this paper’s research is on optimizing the gain spectrum of a bismuth-doped fiber amplifier at wavelengths between 1200 and 1600 nm using modelling and numerical simulation. The research method of this paper is as follows: first of all, after the literature survey, this topic is using the three-energy level structure, and then collecting the data of pump light wavelength and emission absorption cross-section, signal light emission, and absorption cross-section. fit the data to the graph line, and call the genetic optimization algorithm to derive the gain spectrum optimal value. It’s found that when the pump light wavelength is 1230 nm, fiber length is 2 m, bismuth ion doping concentration is 10.0×1024 ions/m3, the signal light wavelength is 1330 m, its amplifier gain spectrum reaches a peak of 57.17 dB, which is consistent with the results of the three-layer cycle (manual search).
An apporoximative theoretical of an erbium-doped fiber amplifier (EDFA) has been proposed in this paper by the rate equation of three-level system. The optimum fiber length is obtained with different pump wavelength by considering the excited-stated-absorption(ESA) in EDFA. The relations between the gain and signal light intensity and pump light intensity are analyzed. It is found that the gain spectrum shape can be changed with the fiber length, which provides the evidence that EDFA is of great potential use in wavelength division multiplexed telecommunication systems.
In this paper, we present the energy level, transition configuration, and numerical model of a bismuth-doped fiber amplifier for the first time, to the best of authorspsila knowledge. With a three-level system, the rate and power propagation equations of the model are solved to examine the effect of the fiber parameter and pump power on the bandwidth of the gain spectra. It can be predicted that when excited at wavelength in the 800-900 nm range, the amplifier can have a ultrabroad gain spectra in the 1.2-1.62 mum range, which cover the low-loss windows of the all-wave fiber.
The Pulse effect on the cross-gain modulation (XGM) in the quantum dot (QD) semiconductor optical amplifiers (SOAs) is investigated using the combining of the SOA power with the QD rate equations system. The QDs structure includes three regions: ground state (GS), excited state (ES) and wetting layer (WL). Thus, a set of rate equations for pump and probe signals is introduced for both steady-state and small-signal power values, which are solved numerically. The pulse shape was included in the analysis, for pump and probe signals. The theoretical results showed a good agreement with the experimental results. It was found that decreasing pulse width of pump/probe ratio is efficient to increase XGM efficiency and bandwidth.