With the rapid development of superconducting quantum computing and the implementation of surface codes, scalable and highly integrated qubit control has emerged as an urgent demand. While optical transmission has been proposed to replace coaxial cables for scalable qubit control, a high-channel-density system with systematically validated qubit coherence and gate performance is still lacking. Here we present a multichannel optical control system implemented using custom optoelectronic circuit boards and evaluate it through a comprehensive benchmarking suite covering the control electronics (equivalent thermal noise), qubit coherence ( T 1 , T 2 ∗ ), and single-qubit and two-qubit gate fidelities. The measured two-qubit controlled-Z (CZ) gate fidelity reaches 99.424±0.083%, demonstrating that the developed multichannel optical control system has met the fidelity requirements for surface-code-based fault-tolerant quantum computing.
With the rapid development of superconducting quantum computing and the implementation of surface codes, scalable and highly integrated qubit control has emerged as an urgent demand. While optical transmission has been proposed to replace coaxial cables for scalable qubit control, a high-channel-density system with systematically validated qubit coherence and gate performance is still lacking. Here we present a multichannel optical control system implemented using custom optoelectronic circuit boards and evaluate it through a comprehensive benchmarking suite covering the control electronics (equivalent thermal noise), qubit coherence ( T 1 , T 2 ∗ ), and single-qubit and two-qubit gate fidelities. The measured two-qubit controlled-Z (CZ) gate fidelity reaches 99.424±0.083%, demonstrating that the developed multichannel optical control system has met the fidelity requirements for surface-code-based fault-tolerant quantum computing.
Superconducting circuits exhibit remarkable potential for constructing large-scale quantum simulation and computation systems, featuring numerous qubits, extended coherence time, and precise control. Nevertheless, the growing number of signal cables poses a challenge in dilution refrigerators due to space and heat load constraints. To overcome this issue, we experimentally implemented an optically-assisted transmission line as an alternative to coaxial cables. By modulating microwave signals on laser intensities at room temperature and regenerating the signals at a cryogenic plate within the dilution refrigerator, we demonstrated full control of superconducting qubits using photocurrent. We demonstrate and benchmark both single-qubit and two-qubit gates on frequency tunable transmon qubits, achieving fidelities of 99.915% ± 0.005% and 99.676% ± 0.041%, respectively, which have reached the requirement of the surface code.
With the rapid development of superconducting quantum computing and the implementation of surface code, large-scale quantum computing is emerging as an urgent demand. In a superconducting computing system, the qubit is maintained in a cryogenic environment to avoid thermal excitation. Thus, the transmission of control signals, which are generated at room temperature, is needed. Typically, the transmission of these signals to the qubit relies on a coaxial cable wiring approach. However, in a large-scale computing system with hundreds or even thousands of qubits, the coaxial cables will pose great space and heat load to the dilution refrigerator. Here, to tackle this problem, we propose and demonstrate a direct-modulation-based optical transmission line. In our experiment, the average single-qubit XEB error and control error are measured as 0.139% and 0.014% separately, demonstrating the feasibility of the optical wiring approach and paving the way for large-scale superconducting quantum computing.
The ability to coherently and reliably manipulate quantum information marks a fundamental technological leap—realizable through a universal, fault‑tolerant quantum computer. Achieving this goal requires progress across all layers of the quantum computing stack, from physical qubits to theoretical algorithms. In this work, we address multiple layers of this stack. We develop a software architecture for scalable device calibration using modular calibration graphs. We introduce real‑time frequency stabilization techniques, demonstrating improved single‑qubit gate fidelities and progress toward multiqubit feedback. Finally, we explore how quantum error correction overhead can be reduced using low‑density parity‑check codes. We present logical protocols for a non‑local nine‑qubit code, which significantly outperforms comparable surface code implementations in both qubit efficiency and computational capability. These results represent practical steps toward overcoming key challenges in fault‑tolerant quantum computing.
The development of robust architectures capable of large-scale fault-tolerant quantum computation should consider both their quantum error-correcting codes and the underlying physical qubits upon which they are built, in tandem.Following this design principle, we demonstrate remarkable error-correction performance by concatenating the XZZX surface code with Kerr-cat qubits.We contrast several variants of fault-tolerant systems undergoing different circuit-noise models that reflect the physics of Kerr-cat qubits.Our simulations show that our system is scalable below a threshold gate infidelity of p CX ∼ 6.5% within a physically reasonable parameter regime, where p CX is the infidelity of the noisiest gate of our system, the controlled-NOT gate.This threshold can be reached in a superconducting-circuit architecture with a Kerr nonlinearity of 10MHz, an approximately 6.25-photon cat qubit, single-photon lifetime of 64 μs, and a thermal photon population 8%.Such parameters are routinely achieved in superconducting circuits.
Superconducting qubits are a leading platform for quantum computation, yet decoherence and scalability challenges continue to limit progress toward fault-tolerant systems. This review synthesizes research on architectures, noise sources, and error correction to clarify performance trade-offs and guide development. The transition from Transmon to Fluxonium has dramatically improved qubit performance, achieving millisecond-scale coherence times. However, this success reveals a fundamental limit of coherence now being primarily restricted by the physical properties of the materials, specifically dielectric losses occurring at the Josephson junction leads and within the surrounding materials. As overcoming these material limits becomes increasingly difficult, system-level engineering determines whether high-coherence qubits can scale.Scaling quantum systems is difficult because current cooling and control systems create too much heat and this forces a shift to integrated digital superconducting circuits and cryogenic light-based links. While these hardware challenges restrict scaling, experiments in error correction show that logical qubits can already outperform physical ones. For example, a distance-7 surface code improved logical qubit lifetime by 2.4×. Achieving practical fault tolerance, however, requires moving beyond simple error models. Future systems must combine techniques like Dynamical Decoupling and Machine Learning-based Optimal Control with dynamic classical control capable of handling complex, correlated faults such as Multi-Bit Burst Errors. Progress in materials, cryogenic system integration for control, and adaptive error management must advance together to realize scalable, high-fidelity quantum hardware.
This thesis explores novel strategies for advancing superconducting quantum computing through a series of experimental investigations and device innovations. Grounded in the development of circuit quantum electrodynamics, the work addresses the challenges posed by the limitations of coherent control, coherence time and scaling of superconducting qubits. Focusing on transmon qubits, the thesis first reviews the foundational principles of circuit quantum electrodynamics and the critical role of the transmon in achieving robust qubit performance. Three experimental studies form the core of this work. The first study demonstrates a universal quantum gate set for strongly coupled transmons. By exploiting the residual ZZ interaction, the work introduces a novel two-axis gate protocol for single-qubit operations and implements both CZ and CNOT gates with high fidelities, highlighting the potential for fast, low-error quantum operations in the strong coupling regime. The second study investigates a dual-rail qubit architecture using parametrically coupled transmons, showcasing a hardware-efficient approach to quantum error correction. This experiment converts single-photon loss errors into detectable erasures and leverages mid-circuit detection to enhance qubit coherence, thereby advancing fault-tolerant quantum computing schemes in the NISQ era. The final study focuses on the development of merged-element transmons (MET) and their FinMET variants. By integrating the Josephson junction and shunt capacitor into a single trilayer device, these innovations achieve a dramatic reduction in device footprint while addressing loss channels through advanced materials engineering, ultimately paving the way for scalable, high-coherence quantum circuits. Collectively, these contributions demonstrate significant progress in quantum gate design, error mitigation, and qubit architecture, offering promising routes toward the realization of largescale, fault-tolerant quantum computers