Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Vacuum Science & Technology A Vacuum Surfaces and Films

Microstructural and optical characterization of Erbium-doped calcium tungstate films on yttria-stabilized zirconia

Sagar Kumar Seth, Bonnie Y.X. Lin, Ignas Masiulionis, Gregory D. Grant, Claire M. McDermott, F. Joseph Heremans, Jiefei Zhang, James M. LeBeau, D. D. Awschalom, Supratik Guha

Published Oct 21, 2026• 0 citations
Publisher

Abstract

Er3+-doped bulk CaWO4 has been demonstrated to be a promising platform for quantum repeaters. However, the use of bulk crystals presents challenges for device integration and scalability. In this paper, we address the scalability of this platform by realizing thin-film CaWO4 growth on yttria-stabilized zirconia wafers, a step toward a CMOS-compatible heterogeneous platform. The films were deposited via radio-frequency magnetron sputtering, a scalable method, followed by postdeposition annealing and were in situ doped with Er. Optical characterization of the Er3+ ions in these films reveals lifetimes of 2.28 ± 0.16 ms, inhomogeneous linewidths of 48.29 ± 0.96 GHz, and a spectral-diffusion-limited homogeneous linewidth of 12.61 ± 2.79 MHz. These results are comparable to previously reported Er3+ in rare-earth oxide thin film hosts. The results highlight the potential of sputtered Er3+-doped CaWO4 thin films for quantum coherent applications.

DOI
10.1116/6.0005722

Related papers

Microstructural and preliminary optical and microwave characterization of erbium-doped CaMoO4 thin films

Ignas Masiulionis, Bonnie Y. X. Lin, Sagar Kumar Seth +10 more

This work explores erbium-doped calcium molybdate (Er:CaMoO4) thin films grown on silicon and yttria stabilized zirconia (YSZ) substrates, as a potential solid state system for C-band (utilizing the ∼1.5 μm Er3+ 4f–4f transition) quantum emitters for quantum network applications. Through molecular beam epitaxial growth experiments and electron microscopy, X-ray diffraction, and reflection electron diffraction studies, we identify an incorporation limited deposition regime that enables a 1:1 Ca:Mo ratio in the growing film leading to single phase CaMoO4 formation that can be in situ doped with Er (typically 2–100 ppm). We further show that growth on silicon substrates is single phase but polycrystalline in morphology, while growth on YSZ substrates leads to high-quality epitaxial single crystalline CaMoO4 films. We perform preliminary optical and microwave characterization on the suspected Y1–Z1 transition of 2 ppm, 200 nm epitaxial Er:CaMoO4 annealed thin films and extract an optical inhomogeneous linewidth of 9.1(1) GHz, an optical excited state lifetime of 6.7(2) ms, a spectral diffusion-limited homogeneous linewidth of 6.7(4) MHz, and an EPR linewidth of 1.10(2) GHz.

arXiv:2508.15122•APL Materials•Oct 1, 2025•3 citations

Optical and microstructural characterization of Er3+ doped epitaxial cerium oxide on silicon

Gregory D. Grant, Jiefei Zhang, Ignas Masiulionis +15 more

Rare-earth ion dopants in solid-state hosts are ideal candidates for quantum communication technologies, such as quantum memories, due to the intrinsic spin–photon interface of the rare-earth ion combined with the integration methods available in the solid state. Erbium-doped cerium oxide (Er:CeO2) is a particularly promising host material platform for such a quantum memory, as it combines the telecom-wavelength (∼1.5μm) 4f–4f transition of erbium, a predicted long electron spin coherence time when embedded in CeO2, and a small lattice mismatch with silicon. In this work, we report on the epitaxial growth of Er:CeO2 thin films on silicon using molecular beam epitaxy, with controlled erbium concentration between 2 and 130 parts per million (ppm). We carry out a detailed microstructural study to verify the CeO2 host structure and characterize the spin and optical properties of the embedded Er3+ ions as a function of doping density. In as-grown Er:CeO2 in the 2–3 ppm regime, we identify an EPR linewidth of 245(1) MHz, an optical inhomogeneous linewidth of 9.5(2) GHz, an optical excited state lifetime of 3.5(1) ms, and a spectral diffusion-limited homogeneous linewidth as narrow as 4.8(3) MHz. We test the annealing of Er:CeO2 films up to 900 °C, which yields narrowing of the inhomogeneous linewidth by 20% and extension of the excited state lifetime by 40%.

arXiv:2309.16644•APL Materials•Feb 1, 2024•28 citations

Erbium-doped yttrium oxide thin films grown by chemical vapor deposition for quantum technologies

Anna Blin, Alexander Kolar, Andrew Kamen +8 more

The obtention of quantum-grade rare-earth-doped oxide thin films that can be integrated with optical cavities and microwave resonators is of great interest for the development of scalable quantum devices. Among the different growth methods, chemical vapor deposition (CVD) offers high flexibility and has demonstrated the ability to produce oxide films hosting rare-earth ions with narrow linewidths. However, growing epitaxial films directly on silicon is challenging by CVD due to a native amorphous oxide layer formation at the interface. In this manuscript, we investigate the CVD growth of erbium-doped yttrium oxide (Er:Y2O3) thin films on different substrates, including silicon, sapphire, quartz, or yttria stabilized zirconia (YSZ). Alternatively, growth was also attempted on an epitaxial Y2O3 template layer on Si (111) prepared by molecular beam epitaxy (MBE) in order to circumvent the issue of the amorphous interlayer. We found that the substrate impacts the film morphology and the crystalline orientations, with different textures observed for the CVD film on the MBE-oxide/Si template (111) and epitaxial growth on YSZ (001). In terms of optical properties, Er3+ ions exhibit visible and IR emission features that are comparable for all samples, indicating a high-quality local crystalline environment regardless of the substrate. Our approach opens interesting prospects to integrate such films into scalable devices for optical quantum technologies.

arXiv:2411.10196•Applied Physics Reviews•Mar 1, 2025•6 citations

Chemically vapor deposited Eu3+:Y2O3 thin films as a material platform for quantum technologies

N. Harada, Alban Ferrier, Diana Serrano +7 more

Rare earth ions hosted in solids are good candidates for quantum technologies due to their chemical stability and optical and spin transitions exhibiting long coherence lifetimes. While bulk oxide crystals are usually the preferred host material, the development of a scalable silicon-compatible thin film platform would be desirable. In this paper, we report on the growth of Y2(1−x)Eu2xO3 thin films on silicon in the full range of Eu3+ concentration by direct liquid injection chemical vapor deposition (CVD). Our sub-micrometer polycrystalline films with a strong-(111) texture were grown for all compositions into the bixbyite cubic phase. The variation of growth rates with temperature and flow indicated that deposition occurred through a mass-transport controlled regime. Optical assessment of the Eu-doped thin films showed inhomogeneous linewidths as narrow as 50 GHz and fluorescence lifetimes of 1 ms for the lowest concentrations. Finally, a spectral hole was successfully burned in a 200 nm-thin film with a 2% Eu doping leading to a homogeneous linewidth of 11 MHz. These values are still below those reported for bulk single crystals indicating that additional decoherence mechanisms exist in such nanometric films, which might be alleviated by further improvement of the crystalline quality. Nevertheless, these results pave the way to the use of CVD-grown Eu:Y2O3 thin films as a platform for integrated quantum devices.

Journal of Applied Physics•Aug 4, 2020•29 citations

Isotopically enriched epitaxial CaWO$_{4}$ thin films for Er$^{3+}$ spin-photon quantum interfaces

Hanlin Tang, Kidae Shin, Ashwin K. Boddeti +10 more

Rare earth ion (REI)-doped oxide thin films are attractive for the application of quantum interconnects due to their stable optical levels and scalability$^{1-3}$. Among them, Er$^{3+}$ doped CaWO$_{4}$ is promising because it possesses narrow optical linewidth transitions and a long spin coherence time$^{4-6}$. The electron spin coherence is limited at high temperatures by paramagnetic impurities and by the presence of the 14.3% $^{183}$W nuclear spin. To further increase the spin coherence time at millikelvin temperatures, where the paramagnetic impurities are frozen out, our approach is to synthesize chemically and isotopically purified thin films as a host material. We first grow non-isotopically enriched Er$^{3+}$ doped CaWO$_{4}$ thin films, which exhibit a 214(13) MHz photoluminescence (PL) inhomogeneous linewidth, indicating the thin film has high crystalline quality. We then grow isotopically enriched CaWO$_{4}$ thin films using an isotopically purified $^{186}$WO$_{3}$ source. Time of flight secondary ion mass spectrometry (ToF-SIMS) was used to measure the relative concentration of W isotopes. $^{183}$W, the only W isotope that has a net nuclear spin and is the major cause of spin decoherence, was at a relative abundance of 1.2%, a factor of 10 lower than natural abundance. We also observed PL emission from single ions after integrating nano-photonic devices with the thin film. These results establish isotopically engineered CaWO$_{4}$ thin films as a promising platform for future studies of nuclear-spin-limited coherence and for scalable rare-earth-ion-based quantum nanophotonic devices.

quant-pharXiv:2604.24582•Apr 28, 2026•1 citation

Development of a Scalable Quantum Memory Platform -- Materials Science of Erbium-Doped TiO$_2$ Thin Films on Silicon

Manish Kumar Singh, Gary Wolfowicz, Jianguo Wen +6 more

Rare-earth ions (REI) have emerged as an attractive candidate for solid-state qubits, particularly as a quantum memory. Their 4f-4f transitions are shielded by filled 5s and 5p orbitals, offering a degree of protection from external electric fields. Embedded within a thin film oxide host, REIs could enable a qubit platform with significant memory capabilities. Furthermore, a silicon-compatible thin film form factor would enable the use of standard semiconductor fabrication processes to achieve chip-based integrability and scalability for functional quantum networks. Towards this goal, we have carried out optical and microstructural studies of erbium-doped polycrystalline and epitaxial TiO$_2$ thin films on Si (100), r-sapphire, and SrTiO$_3$ (100). We observe that the inhomogeneous optical linewidth of the Er photoluminescence is comparable or better for polycrystalline Er:TiO$_2$(grown on Si) in comparison to single crystal epitaxial films on sapphire or SrTiO$_3$, implying a relative insensitivity to extended defects. We investigated the effect of the film/substrate and film/air interface and found that the inhomogeneous linewidth and spectral diffusion can be significantly improved via bottom buffer and top capping layers of undoped TiO$_2$. Using such approaches, we obtain inhomogeneous linewidths of 5.2 GHz and spectral diffusion of 180 MHz in Er:TiO$_2$ /Si(100) films and have demonstrated the engineerability of quantum-relevant properties in these thin films.

arXiv:2202.05376•Feb 11, 2022•10 citations
Er3+-doped bulk CaWO4 has been demonstrated to be a promising platform for quantum repeaters. However, the use of bulk crystals presents challenges for device integration and scalability. In this paper, we address the scalability of this platform by realizing thin-film CaWO4 growth on yttria-stabilized zirconia wafers, a step toward a CMOS-compatible heterogeneous platform. The films were deposited via radio-frequency magnetron sputtering, a scalable method, followed by postdeposition annealing and were in situ doped with Er. Optical characterization of the Er3+ ions in these films reveals lifetimes of 2.28 ± 0.16 ms, inhomogeneous linewidths of 48.29 ± 0.96 GHz, and a spectral-diffusion-limited homogeneous linewidth of 12.61 ± 2.79 MHz. These results are comparable to previously reported Er3+ in rare-earth oxide thin film hosts. The results highlight the potential of sputtered Er3+-doped CaWO4 thin films for quantum coherent applications.
This work explores erbium-doped calcium molybdate (Er:CaMoO4) thin films grown on silicon and yttria stabilized zirconia (YSZ) substrates, as a potential solid state system for C-band (utilizing the ∼1.5 μm Er3+ 4f–4f transition) quantum emitters for quantum network applications. Through molecular beam epitaxial growth experiments and electron microscopy, X-ray diffraction, and reflection electron diffraction studies, we identify an incorporation limited deposition regime that enables a 1:1 Ca:Mo ratio in the growing film leading to single phase CaMoO4 formation that can be in situ doped with Er (typically 2–100 ppm). We further show that growth on silicon substrates is single phase but polycrystalline in morphology, while growth on YSZ substrates leads to high-quality epitaxial single crystalline CaMoO4 films. We perform preliminary optical and microwave characterization on the suspected Y1–Z1 transition of 2 ppm, 200 nm epitaxial Er:CaMoO4 annealed thin films and extract an optical inhomogeneous linewidth of 9.1(1) GHz, an optical excited state lifetime of 6.7(2) ms, a spectral diffusion-limited homogeneous linewidth of 6.7(4) MHz, and an EPR linewidth of 1.10(2) GHz.
Rare-earth ion dopants in solid-state hosts are ideal candidates for quantum communication technologies, such as quantum memories, due to the intrinsic spin–photon interface of the rare-earth ion combined with the integration methods available in the solid state. Erbium-doped cerium oxide (Er:CeO2) is a particularly promising host material platform for such a quantum memory, as it combines the telecom-wavelength (∼1.5μm) 4f–4f transition of erbium, a predicted long electron spin coherence time when embedded in CeO2, and a small lattice mismatch with silicon. In this work, we report on the epitaxial growth of Er:CeO2 thin films on silicon using molecular beam epitaxy, with controlled erbium concentration between 2 and 130 parts per million (ppm). We carry out a detailed microstructural study to verify the CeO2 host structure and characterize the spin and optical properties of the embedded Er3+ ions as a function of doping density. In as-grown Er:CeO2 in the 2–3 ppm regime, we identify an EPR linewidth of 245(1) MHz, an optical inhomogeneous linewidth of 9.5(2) GHz, an optical excited state lifetime of 3.5(1) ms, and a spectral diffusion-limited homogeneous linewidth as narrow as 4.8(3) MHz. We test the annealing of Er:CeO2 films up to 900 °C, which yields narrowing of the inhomogeneous linewidth by 20% and extension of the excited state lifetime by 40%.
The obtention of quantum-grade rare-earth-doped oxide thin films that can be integrated with optical cavities and microwave resonators is of great interest for the development of scalable quantum devices. Among the different growth methods, chemical vapor deposition (CVD) offers high flexibility and has demonstrated the ability to produce oxide films hosting rare-earth ions with narrow linewidths. However, growing epitaxial films directly on silicon is challenging by CVD due to a native amorphous oxide layer formation at the interface. In this manuscript, we investigate the CVD growth of erbium-doped yttrium oxide (Er:Y2O3) thin films on different substrates, including silicon, sapphire, quartz, or yttria stabilized zirconia (YSZ). Alternatively, growth was also attempted on an epitaxial Y2O3 template layer on Si (111) prepared by molecular beam epitaxy (MBE) in order to circumvent the issue of the amorphous interlayer. We found that the substrate impacts the film morphology and the crystalline orientations, with different textures observed for the CVD film on the MBE-oxide/Si template (111) and epitaxial growth on YSZ (001). In terms of optical properties, Er3+ ions exhibit visible and IR emission features that are comparable for all samples, indicating a high-quality local crystalline environment regardless of the substrate. Our approach opens interesting prospects to integrate such films into scalable devices for optical quantum technologies.
Rare earth ions hosted in solids are good candidates for quantum technologies due to their chemical stability and optical and spin transitions exhibiting long coherence lifetimes. While bulk oxide crystals are usually the preferred host material, the development of a scalable silicon-compatible thin film platform would be desirable. In this paper, we report on the growth of Y2(1−x)Eu2xO3 thin films on silicon in the full range of Eu3+ concentration by direct liquid injection chemical vapor deposition (CVD). Our sub-micrometer polycrystalline films with a strong-(111) texture were grown for all compositions into the bixbyite cubic phase. The variation of growth rates with temperature and flow indicated that deposition occurred through a mass-transport controlled regime. Optical assessment of the Eu-doped thin films showed inhomogeneous linewidths as narrow as 50 GHz and fluorescence lifetimes of 1 ms for the lowest concentrations. Finally, a spectral hole was successfully burned in a 200 nm-thin film with a 2% Eu doping leading to a homogeneous linewidth of 11 MHz. These values are still below those reported for bulk single crystals indicating that additional decoherence mechanisms exist in such nanometric films, which might be alleviated by further improvement of the crystalline quality. Nevertheless, these results pave the way to the use of CVD-grown Eu:Y2O3 thin films as a platform for integrated quantum devices.
Isotopically enriched epitaxial CaWO4_{4}4​ thin films for Er3+^{3+}3+ spin-photon quantum interfaces
Rare earth ion (REI)-doped oxide thin films are attractive for the application of quantum interconnects due to their stable optical levels and scalability1−3^{1-3}1−3. Among them, Er3+^{3+}3+ doped CaWO4_{4}4​ is promising because it possesses narrow optical linewidth transitions and a long spin coherence time4−6^{4-6}4−6. The electron spin coherence is limited at high temperatures by paramagnetic impurities and by the presence of the 14.3% 183^{183}183W nuclear spin. To further increase the spin coherence time at millikelvin temperatures, where the paramagnetic impurities are frozen out, our approach is to synthesize chemically and isotopically purified thin films as a host material. We first grow non-isotopically enriched Er3+^{3+}3+ doped CaWO4_{4}4​ thin films, which exhibit a 214(13) MHz photoluminescence (PL) inhomogeneous linewidth, indicating the thin film has high crystalline quality. We then grow isotopically enriched CaWO4_{4}4​ thin films using an isotopically purified 186^{186}186WO3_{3}3​ source. Time of flight secondary ion mass spectrometry (ToF-SIMS) was used to measure the relative concentration of W isotopes. 183^{183}183W, the only W isotope that has a net nuclear spin and is the major cause of spin decoherence, was at a relative abundance of 1.2%, a factor of 10 lower than natural abundance. We also observed PL emission from single ions after integrating nano-photonic devices with the thin film. These results establish isotopically engineered CaWO4_{4}4​ thin films as a promising platform for future studies of nuclear-spin-limited coherence and for scalable rare-earth-ion-based quantum nanophotonic devices.
Development of a Scalable Quantum Memory Platform -- Materials Science of Erbium-Doped TiO2_22​ Thin Films on Silicon
Rare-earth ions (REI) have emerged as an attractive candidate for solid-state qubits, particularly as a quantum memory. Their 4f-4f transitions are shielded by filled 5s and 5p orbitals, offering a degree of protection from external electric fields. Embedded within a thin film oxide host, REIs could enable a qubit platform with significant memory capabilities. Furthermore, a silicon-compatible thin film form factor would enable the use of standard semiconductor fabrication processes to achieve chip-based integrability and scalability for functional quantum networks. Towards this goal, we have carried out optical and microstructural studies of erbium-doped polycrystalline and epitaxial TiO2_22​ thin films on Si (100), r-sapphire, and SrTiO3_33​ (100). We observe that the inhomogeneous optical linewidth of the Er photoluminescence is comparable or better for polycrystalline Er:TiO2_22​(grown on Si) in comparison to single crystal epitaxial films on sapphire or SrTiO3_33​, implying a relative insensitivity to extended defects. We investigated the effect of the film/substrate and film/air interface and found that the inhomogeneous linewidth and spectral diffusion can be significantly improved via bottom buffer and top capping layers of undoped TiO2_22​. Using such approaches, we obtain inhomogeneous linewidths of 5.2 GHz and spectral diffusion of 180 MHz in Er:TiO2_22​ /Si(100) films and have demonstrated the engineerability of quantum-relevant properties in these thin films.