The quantum bits (qubits) on which superconducting quantum computers are based have energy scales corresponding to photons with GHz frequencies. The energy of photons in the gigahertz domain is too low to allow transmission through the noisy room-temperature environment, where the signal would be lost in thermal noise. Optical photons, on the other hand, have much higher energies, and signals can be detected using highly efficient single-photon detectors. Transduction from microwave to optical frequencies is therefore a potential enabling technology for quantum devices. High conversion efficiency and high fidelity (the similarity of input microwave state to the output optical state.) are important characteristics of these devices. In such devices, the efficiency of the up-conversion process is typically improved by increasing the power in the pump. In addition to this, the optical pump is dissipated as thermal photons via absorption-induced heating into the system. Since the frequency of thermal photons and qubits are in the same range, this can affect the quality of the transferred quantum state which is characterized by fidelity. Thus, the optical pump can be a source of thermal noise and degrade the fidelity. Realizing an optimum pump power level while investigating its effect on fidelity via temperature are important tasks in the evolution of these upconversion devices. In this work, we explore two kinds of hybrid quantum devices that can be used as frequency upconverts; the first one is a resonant electro-optic modulator consisting of a microwave cavity and a WGM resonator (made of LiNbO3) and the next one is a magneto-optic modulator consisting of a microwave cavity and the rare earth crystal gadolinium vanadate (GdVO4) in the cuboid shape. We model the sub-Kelvin thermal behavior of an electro-optic transducer based on a lithium niobate whispering gallery mode resonator. We compute thermal photon numbers and find that there is an optimum power level for a continuous pump, whilst pulsed operation of the pump increases the fidelity of the conversion. In the magneto-optic modulator via photon-magnon coupling, we investigate the effect of GdVO4 temperature on the linewidth of magnons and the strength of photon-magnon coupling inside a dilution refrigerator. In the next step, we investigate the effect of absorption-induced heating of GdVO4 on the linewidth of magnons and the strength of photon-magnon coupling inside a dilution refrigerator, and the temperature of GdVO4 is estimated via comparison of two methods. The effect of heating of the GdVO4 via the mentioned methods on the transmission spectrum and the resonance frequency of the microwave cavity is studied. The transmission spectrum is used to comprehend the time evolution of the thermal equilibrium of the sample and estimate its temperature.
The quantum bits (qubits) on which superconducting quantum computers are based have energy scales corresponding to photons with GHz frequencies. The energy of photons in the gigahertz domain is too low to allow transmission through the noisy room-temperature environment, where the signal would be lost in thermal noise. Optical photons, on the other hand, have much higher energies, and signals can be detected using highly efficient single-photon detectors. Transduction from microwave to optical frequencies is therefore a potential enabling technology for quantum devices. High conversion efficiency and high fidelity (the similarity of input microwave state to the output optical state.) are important characteristics of these devices. In such devices, the efficiency of the up-conversion process is typically improved by increasing the power in the pump. In addition to this, the optical pump is dissipated as thermal photons via absorption-induced heating into the system. Since the frequency of thermal photons and qubits are in the same range, this can affect the quality of the transferred quantum state which is characterized by fidelity. Thus, the optical pump can be a source of thermal noise and degrade the fidelity. Realizing an optimum pump power level while investigating its effect on fidelity via temperature are important tasks in the evolution of these upconversion devices. In this work, we explore two kinds of hybrid quantum devices that can be used as frequency upconverts; the first one is a resonant electro-optic modulator consisting of a microwave cavity and a WGM resonator (made of LiNbO3) and the next one is a magneto-optic modulator consisting of a microwave cavity and the rare earth crystal gadolinium vanadate (GdVO4) in the cuboid shape. We model the sub-Kelvin thermal behavior of an electro-optic transducer based on a lithium niobate whispering gallery mode resonator. We compute thermal photon numbers and find that there is an optimum power level for a continuous pump, whilst pulsed operation of the pump increases the fidelity of the conversion. In the magneto-optic modulator via photon-magnon coupling, we investigate the effect of GdVO4 temperature on the linewidth of magnons and the strength of photon-magnon coupling inside a dilution refrigerator. In the next step, we investigate the effect of absorption-induced heating of GdVO4 on the linewidth of magnons and the strength of photon-magnon coupling inside a dilution refrigerator, and the temperature of GdVO4 is estimated via comparison of two methods. The effect of heating of the GdVO4 via the mentioned methods on the transmission spectrum and the resonance frequency of the microwave cavity is studied. The transmission spectrum is used to comprehend the time evolution of the thermal equilibrium of the sample and estimate its temperature.
Abstract The quantum bits (qubits) on which superconducting quantum computers are based have energy scales corresponding to photons with GHz frequencies. The energy of photons in the gigahertz domain is too low to allow transmission through the noisy room-temperature environment, where the signal would be lost in thermal noise. Optical photons, on the other hand, have much higher energies, and signals can be detected using highly efficient single-photon detectors. Transduction from microwave to optical frequencies is therefore a potential enabling technology for quantum devices. However, in such a device the optical pump can be a source of thermal noise and thus degrade the fidelity; the similarity of input microwave state to the output optical state. In order to investigate the magnitude of this effect we model the sub-Kelvin thermal behavior of an electro-optic transducer based on a lithium niobate whispering gallery mode resonator. We find that there is an optimum power level for a continuous pump, whilst pulsed operation of the pump increases the fidelity of the conversion.
Superconducting qubits are currently one of the leading qubit designs, showing great success in some of the world's most powerful quantum computers. Superconducting qubits, however, communicate at microwave frequencies, which is problematic when it comes to the task of long distance communication as unless the communication channel is cryogenically cooled the microwave photons are swamped by thermal noise. Optical photons, on the other hand, are ideal for long distance communication, particularly at frequencies that lie within the telecommunications band. One solution to the superconducting qubits communication problem is to create a device that can convert an input microwave photon into an optical photon with unit quantum efficiency. A device of such could then be used alongside existing optical fibre networks to connect distant superconducting processors. Furthermore, an upconversion device would allow superconducting qubit systems to take advantage of quantum technologies in the optical region, such as optical quantum memories.\n\nSeveral different approaches have been taken in attempts to experimentally implement such a device. Recently a theoretical proposal showed that the strong non-linearities that occur near the collective resonances in fully concentrated rare-earth crystals can be used to efficiently upconvert microwave photons. In this thesis we begin experimental investigations of two fully concentrated rare-earth crystals, GdVO4 and DyPO4, for their application to microwave upconversion.\n\nAbsorption spectra of the two crystals in the optical region are measured using a Fourier transform infrared spectrometer, in order to characterise and explore the possible optical states to be used in the upconversion process. Experiments are then carried out at microwave frequencies to explore the coupling between the collective spin resonances (magnons) that occur within the crystals and a microwave cavity. It is found that not only can the ultrastrong coupling regime be reached in these systems but that the linewidth of the magnon mode is narrow, measuring 35MHz at T = 25mK. This is the first experimental evidence of ultrastrong coupling between a microwave cavity and antiferromagnetic magnon modes in a rare-earth crystal. Furthermore, narrow transition linewidths are a crucial requirement in the proposed upconversion method, therefore the narrow linewidth experimentally measured here is an important validation of the proposals feasibility. \n\nThe results presented in this thesis show that microwave upconversion mediated by fully concentrated rare-earth crystals has an exciting future. Perhaps one day rare-earth crystals will be used to overcome the major communication problem superconducting qubits currently face.
The development of scalable quantum networks requires coherent interfaces capable of converting microwave photons used in superconducting quantum processors into optical photons suitable for long-distance fiber transmission. This review surveys recent progress in microwave-to-optical quantum transduction across optomechanical, electro-optic, and magneto-optic platforms, with emphasis on conversion efficiency, bandwidth, added noise, and operating temperature. In addition to standard metrics, we propose the internal efficiency eta_in and the magnon decay rate kappa_m/2pi as normalized parameters that enable fairer comparison across heterogeneous implementations. Optomechanical systems achieve internal phonon-to-photon efficiencies of 93% with sub-quantum added noise of 0.25 quanta at millikelvin temperatures. Electro-optic devices based on LiNbO3 and AlN have advanced from room-temperature efficiencies below 1% to millikelvin systems with internal efficiencies approaching 99.5%, added noise as low as 0.16 quanta at 60 mK, and bandwidths extending to several tens of megahertz. Magneto-optic (optomagnonic) platforms exhibit the lowest efficiencies (typically 10−10 to 10−8), but offer intrinsic non-reciprocity and broadband magnonic operation, with emerging approaches based on topological heterostructures and magnon squeezing predicting enhancements up to 10−4. Optomechanical systems appear promising for high-fidelity quantum state transfer, electro-optic transducers for high-bandwidth coherent links, and magneto-optic devices for non-reciprocal network components. We discuss the fundamental trade-off between efficiency and added noise across all three platforms, and argue that heterogeneous microwave-optical transduction is emerging as a key enabling technology for distributed quantum computing and large-scale quantum networks.
Transduction of quantum signals between the microwave and the optical ranges will unlock powerful hybrid quantum systems enabling information processing with superconducting qubits and low-noise quantum networking through optical photons. Most microwave-to-optical quantum transducers suffer from thermal noise due to pump absorption. We analyze the coupled thermal and wave dynamics in electro-optic transducers that use a two-step scheme based on an intermediate frequency state in the THz range. Our analysis, supported by numerical simulations, shows that the two-step scheme operating with a continuous pump offers near-unity external efficiency with a multiorder noise suppression compared to single-step transduction. As a result, two-step electro-optic transducers may enable quantum-noise-limited interfacing of superconducting quantum processors with optical channels at MHz-scale bit rates.
Radio frequency (RF) radiation is a powerful tool in computing, communication, and sensing due to the ability to engineer strong electrical interactions. Within cryogenic systems, in particular, microwave (MW) frequency superconducting qubits have demonstrated promise as a platform for quantum computing, and MW and millimeter-wave (mmW) systems have been valuable tools in sensing. However, owing to their low energy, the weak, single-photon level signals employed by these systems suffer high sensitivity to thermal noise when they exit the thermal bath, as well as short attenuation lengths due to absorption and scattering in cables. Telecommunication frequency optical photons, meanwhile, have long propagation lengths and can be supported by low-loss optical fibers. The high photon energy makes signals insensitive to thermal noise, and the high frequency can allow many RF signals to be multiplexed onto a single optical carrier. Interfacing RF and optical radiation to leverage both strong interactions with macroscopic systems characteristic of electrical interactions and low-loss propagation characteristic of optical photons has been critical to realizing our global communication system. Leveraging the infrastructure developed to support this industry, such as single photon detectors, is attractive for scaling cryogenic RF systems. Coherent conversion processes, especially, can benefit a wide range of applications, especially in computing and sensing, by preserving quantum states, and retaining phase information necessary for quantum gates, and enable the use of measurement techniques that can increase detection sensitivity. This dissertation focuses on using the electro-optic effect in thin-film lithium niobate to form an efficient, coherent interface between radio- and telecommunication-frequency photons. Lithium niobate is an attractive platform due to its high electro-optic coefficient (approx. 30 pm/V), wide transparency window (DC to 400 THz), and ability to support low-loss optical waveguides (.2 dB/m), all of which deviate little from room temperature down to near-zero Kelvin environments. First, I explore the development of low-loss lithium niobate optical cavities and operation of lithium niobate waveguides at low temperatures. While lithium niobate is an electro-optic material with a DC response, using the electro-optic response at room temperature for stable biasing and low-frequency operation has remained a challenge. A temperature- and frequency-dependent study is conducted to identify lithium charge migration as a potential screening mechanism suppressed at low temperatures. Next, I explore the use of RF-cavity enhanced, triply resonant photonic molecules (created from two coupled low-loss optical cavities) for forming efficient electro-optic interfaces with microwave (3-10 GHz) and millimeter wave (100 GHz) radiation. In the microwave regime, I explore microwave-optical transduction for forming optical interfaces with microwave qubits, specifically focusing on superconducting qubits. The characterization of one such transducer is demonstrated, and the device is used to optically synthesize microwave signals at low temperatures, bypassing the need for input microwave control lines. Outlook for other interfaces, including optical photon mediated quantum information transfer, is discussed. At mmW frequencies, the triply resonant photonic molecule is explored for low-power ( mW) optical-frequency shifting.
Atoms and photons, two things so different but yet so alike. The former, the building block of matter, something we learn about in school and imagine it as some tiny marbles encircled by other tinier marbles. The latter, an electromagnetic wave, a light particle or an excitation of the electromagnetic field. Quantum mechanics tells us about the properties of these two entities. And even if it sounds, looks and writes counter-intuitive, it has proven right for over a century now. In this work, I elaborate on how we tested the laws of quantum mechanics and how we used them learn more about the tiny building blocks of nature and the fields they use to talk to each other. The atoms we use, are artificial. Superconducting qubits, small electrical circuits with quantized energy levels behave like electrons that transition between different orbitals in an atom. One of the qubits' advantages, is also a big disadvantage. We design the circuits' energy levels and fabricate them in a cleanroom. This allows for arbitrary spaced energy levels but in contrast to real atoms, prevents two superconducting qubits from being alike. Still, this qubit platform is one of the frontrunners for future quantum computing technology and testing fundamental physics due to their scalability. We interface superconducting qubits, which operate in the GHz regime, with microwave photons. We use 3D aluminum cavities as mediators between qubits and photons. The cavities allow for non-destructive readout of the qubit state, they shield the qubits from noise at the qubit frequency and they give us an easy way to frequency-tune these joint systems. We need to operate superconducting qubits and their cavities at millikelvin temperatures in dilution refrigerators. At higher temperatures, superconductivity suffers and even worse, the environment is filled with thermal noise photons. This poses a fundamental limitation on the scalability of superconducting qubit devices. Also connecting multiple devices in different fridges does not work over room temperature links because the microwave photons used for this purpose will be covered in noise and the quantum information they carry, will be unusable. Infrared photons do not suffer from this noise problem since there are close to zero thermal noise photons at their frequencies at room temperature. We cannot simply interface superconducting devices with optical photons due their frequency mismatch and the destructive effect of optical photons on superconductors. Therefore, we use microwave-to-optics transducers that allow to convert microwave photons into optical ones and vice-versa. The transducers that we use are macroscopic electro-optic transducers using the Pockels effect in a disk-shaped Lithium Niobate whispering gallery mode resonator. By using a strong optical pump, photons from the two frequency domains experience a beam-splitter interaction and get converted from one to the other. We measure the generated optical photons using elaborate optical setups, optical heterodyning and single photon detectors to gain knowledge about the qubit state or the converted microwave photons. Bridging the microwave and the optical world allows us to take advantage of both of their strengths but it also requires deep knowledge about both of their working principles. In this work, we describe two experiments that our group conducted to showcase the opportunities that arise from interfacing superconducting qubits with optical photons but also the pitfalls, one may encounter on the way. In the first experiment, we managed to all-optically read out a superconducting qubit. We show that the assignment fidelity, the probability that a measurement of the qubit state matches the prepared state, is close to equal for all-optical, microwave-to-optics and conventional microwave readout. We show T1 and T2 measurements for all three readout types and give an analysis of the noise caused by the optics. Finally, we show that the infrared light does not affect the qubit performance in a negative way but that the heating it causes does. This is an important insight that we used in the next experiment. The second experiment is the upconversion of itinerant single microwave photons to the optical domain. We show that we can generate single microwave photons from a qubit-cavity system. We upconvert these single photons, measure them with a single photon detector and reconstruct their shape. By conducting a single photon Rabi measurement, we show correlations between the microwave and the optical domain. And by thorough signal-to-noise measurements and noise analysis, we find that we can generate single infrared photons with high signal-to-noise ratio 5.1 and low transducer added noise (<0.012 quanta). We show that this measurement creates a path towards entanglement of a superconducting qubit and an optical photon and what parameters need to be improved to achieve it. Additionally, this experiment is a proof of principle for an on-demand infrared single photon source. More generally, it allows to link microwave quantum technology in general to the optical domain.