Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconductor Science and Technology

Exploiting stable double switching in single-flux-quantum circuits for compact scaled unary addition

Zeyu Han, Nobuyuki Yoshikawa, Yuki Yamanashi

Published Sep 21, 2026• 0 citations
Publisher

Abstract

Abstract Single-flux-quantum (SFQ) circuits conventionally avoid simultaneous or competing switching events in Josephson junction (JJ) comparator because they can induce pulse errors and nondeterministic behavior. In this work, we demonstrate that such double switching can instead be intentionally exploited as a useful computational mechanism. By introducing unshunted JJs before the comparator structure, stable double switching of two junctions is realized, enabling two input SFQ pulses to be merged into a single output pulse. The proposed mechanism operates correctly regardless of the switching order of the two junctions. To demonstrate the feasibility of the double switching mechanism, a double-switching confluence buffer was designed as a compact scaled unary adder. The proposed adder requires only 12 JJs, achieving approximately 84% area reduction compared with a conventional SFQ scaled unary adder. Simulations achieved bias margins of −18.6% to +20.2%, while measured bias margins of +17.9% to +28.5% and correct operation up to approximately 55 GHz were experimentally demonstrated. The results indicate that double switching, traditionally regarded as undesirable in SFQ circuit design, can instead be harnessed as a useful primitive for compact SFQ logic circuits.

DOI
10.1088/1361-6668/aeaab4

Related papers

A superconducting unary arithmetic logic unit with ultra-low hardware cost

Zeyu Han, Nobuyuki Yoshikawa, Yuki Yamanashi

Abstract Single-flux-quantum (SFQ) circuits are promising candidates for post-Moore integrated circuits owing to their ultra-high-speed operation and low power consumption. However, limitations in current superconducting fabrication processes pose significant challenges to achieving area-efficient SFQ-based microprocessors, particularly in the design of compact arithmetic logic units (ALUs). Unary computing enables arithmetic operations using extremely simple logic, but typically suffers from long computation latency. This paper focuses on unary computing for superconducting circuits that exploits the complementary characteristics of SFQ logic and unary computing. The ultra-high-speed nature of SFQ circuits compensates for the inherent latency of unary computation, while unary computing enables an ultra-low hardware cost by substantially reducing circuit complexity. Based on this concept, we introduce a unary computing methodology tailored for SFQ circuits and design a superconducting unary ALU with ultra-low hardware cost. The proposed ALU requires only 183 Josephson junctions (JJs), achieving approximately 88.2% reduction in JJ count and 80.4% reduction in area compared with a conventional bit-serial SFQ ALU. The proposed design, including binary-to-unary and unary-to-binary converters, was fabricated using a 10 kA cm −2 Nb four-layer superconducting circuit fabrication process and experimentally verified to operate correctly at approximately 72 GHz. The total power consumption at this frequency is approximately 58.9 µ W. This work quantitatively demonstrates the effectiveness of combining unary computing with SFQ circuits for ultra-low-cost processing systems and provides superconducting circuits as a new design option for alternative computation paradigms, such as unary computing.

Superconductor Science and Technology•Jun 5, 2026•0 citations

Stacked Josephson Junctions as Inductors for Single Flux Quantum Circuits

Manuel A. Castellanos-Beltran, David I. Olaya, Adam J. Sirois +3 more

Large-scale integration of single flux quantum (SFQ) circuits requires components as compact as possible. In this paper, we study the feasibility of integrating vertically stacked Josephson inductors (VSJIs) fabricated with self-shunted Josephson junctions into our SFQ-based circuits, and use both dc and RF electrical measurements to verify the performance of these junction stacks as compact inductors. The VSJIs consist of three Josephson junctions stacked vertically and are inserted into test structures to validate their potential as compact alternatives to geometrical inductors. The VSJIs are designed to be non-switching junctions and are combined with smaller area, switching Josephson junctions fabricated with the same junction barrier process. The VSJIs have a designed critical current of approximately 50% greater than that of the switching junctions, and their observed behavior can be modeled correctly by including the known nonlinearity of the Josephson inductance. To confirm that this nonlinearity does not degrade the expected bias margins, we simulate two common types of SFQ cells with the geometrical inductors replaced by VSJIs. The results verify that incorporating VSJIs in SFQ circuits would increase circuit density with minimal impact on circuit margins.

IEEE Transactions on Applied Superconductivity•Feb 27, 2019•21 citations

Simulation of the Margins in Single Flux Quantum Circuits Containing π-Shifted Josephson Junctions

Yuki Yamanashi, Sotaro Nakaishi, Nobuyuki Yoshikawa

We designed several single flux quantum (SFQ) flip-flops and logic gates composed of Josephson junctions (JJs) and π-shifted JJs (π-JJs) to quantitatively evaluate effectiveness of introduction of π-JJs into the SFQ logic circuit. One-output flip-flops and logic gates were designed on the basis of the circuit design methodology we built for the SFQ circuit containing π-JJs. The designed flip-flops and logic gates have wide operating margins, the dc-bias margins of larger than ±30%, and device parameter margins of ±18%, though the static power consumption are reduced compared to conventional ones composed of JJs. We found that the difference in the critical current density between JJs and π-JJs does not affect the operating margins of the SFQ flip-flop composed of JJs and π-JJs. We devised a circuit structure of the delay flip-flop with complementary outputs composed of JJs and π-JJs (π-DFFC). The analog circuit simulation shows the dc-bias margin of the π-DFFC is larger than ±33%. These results indicate that the large-scale SFQ logic circuit system can be implemented using the flip-flops and logic gates containing π-JJs.

IEEE Transactions on Applied Superconductivity•Mar 18, 2019•12 citations

Small-area and high-precision deterministic stochastic adder using single flux quantum circuit

Zeyu Han, Yuya Mandai, Nobuyuki Yoshikawa +1 more

Abstract Superconducting single flux quantum (SFQ) circuits can operate at ultrafast speeds, and their superconducting random number generators (SRNGs) produce high-quality stochastic bit sequences at several tens GHz, with an arbitrary probability of outputting ‘1’, making them ideal for stochastic computing. The conventional superconducting stochastic adder uses a multiplexer (MUX) controlled by a random bit sequence generated by the SRNG. However, the SFQ-based MUX occupies a large circuit area, and any deviation in the probability of the control signal directly degrades the accuracy of stochastic addition. To overcome these limitations, we propose a deterministic stochastic adder comprising only an AND gate, an XOR gate, and a toggle flip-flop. Our design outputs one ‘1’ for every two input ‘1’s, achieving stochastic addition without the random control signal. Compared to the MUX-based stochastic adder, the proposed adder reduces the root-mean-square error by a factor of 32 when adding 1024-bit random sequences, reduces circuit area by 49.0%, and Josephson junction count by 28.1%, while supporting operating frequencies of about 120 GHz in simulation. We fabricated the proposed adder with two SRNGs for generating input sequences using a 10 kA cm −2 Nb four-layer superconducting process. High-speed operation was verified up to approximately 35.4 GHz with a constant bias margin by measuring the average voltage at the input and outputs. To the best of our knowledge, this is the first demonstration of ultrafast stochastic arithmetic operations above 30 GHz.

Superconductor Science and Technology•Jan 1, 2026•1 citation

Design methodology of single-flux-quantum flip-flops composed of both 0- and π-shifted Josephson junctions

Yuki Yamanashi, Sotaro Nakaishi, Akira Sugiyama +2 more

A methodology for designing single-flux-quantum (SFQ) flip-flops composed of both conventional (0-) and π -shifted Josephson junctions is investigated. We investigated the implementation of a storage loop, which can store flux quantum and is indispensable to express binary logic states in superconductor logic circuits. As all SFQ flip-flops have storage loops, the investigated design methodology can be applied to their design. We designed several SFQ flip-flops composed of 0- and π -shifted Josephson junctions using the investigated design methodology. The performances of the designed SFQ flip-flops were quantitatively evaluated by using an analog circuit simulator which we developed. We confirmed the correct operation of various SFQ flip-flops composed of 0- and π -shifted Josephson junctions with wide operating margins. Moreover, we observed that the investigated design methodology is suitable for SFQ flip-flops with complementary outputs because a storage loop composed of both 0- and π -shifted Josephson junctions has a symmetric structure and the complementary output function can be realized by using the storage loop. Our investigation indicates that the number of Josephson junctions and static power consumption of a non-destructive read-out flip-flop with complementary outputs (NDROC) can be reduced to less than half of those of the conventional NDROC, which has two storage loops composed of 0-Josephson junctions, to realize the complementary output function. The investigated design methodology is expected to be applied to not only SFQ circuits but also other superconducting logic circuits and novel reconfigurable logic devices using programmable 0- π Josephson junctions.

Superconductor Science and Technology•Aug 2, 2018•38 citations

High-Capacity DFF Cells for Unary Computing Using Single-Flux Quantum Circuits

Zeyu Han, Nobuyuki Yoshikawa, Yuki Yamanashi

Due to their high-speed operation and low power consumption, single flux quantum (SFQ) circuits are promising technologies for integrated circuits. However, current superconducting fabrication limitations impose strict area constraints, challenging the construction of large-scale systems. Unary computing (UC) encodes numerical values by concentrating all “1”s at the beginning of a bit sequence. This approach enables arithmetic operations with fewer logic gates, thereby improving the area efficiency. In this study, we propose a novel high-capacity D flip-flop (HC-DFF) cell for UC-based SFQ circuits that achieves high-density data registration while preserving UC encoding. The HC-DFF employs a cascaded storage loop structure in which each loop sequentially stores one flux quantum, avoiding the margin deterioration associated with storing multiple flux quanta in a single loop. Simulation shows that the proposed HC-DFF achieves a bias margin of –20.8% to +32.7% and supports read/write operations above 100 GHz. We fabricated the HC-DFF using a 10 kA/cm² Nb four-layer superconducting process and verified its operation through low-speed measurements. The HC-DFF offers enhanced scalability and stability while reducing the number of required Josephson junctions by 83.3% per bit compared to conventional DFF-based shift registers for saving UC signals. For short unary sequences of less than 31 bits, it retains an advantage over storing binary data with equivalent precision using conventional DFF-based shift registers.

IEEE Transactions on Applied Superconductivity•Aug 25, 2025•2 citations
Abstract Single-flux-quantum (SFQ) circuits conventionally avoid simultaneous or competing switching events in Josephson junction (JJ) comparator because they can induce pulse errors and nondeterministic behavior. In this work, we demonstrate that such double switching can instead be intentionally exploited as a useful computational mechanism. By introducing unshunted JJs before the comparator structure, stable double switching of two junctions is realized, enabling two input SFQ pulses to be merged into a single output pulse. The proposed mechanism operates correctly regardless of the switching order of the two junctions. To demonstrate the feasibility of the double switching mechanism, a double-switching confluence buffer was designed as a compact scaled unary adder. The proposed adder requires only 12 JJs, achieving approximately 84% area reduction compared with a conventional SFQ scaled unary adder. Simulations achieved bias margins of −18.6% to +20.2%, while measured bias margins of +17.9% to +28.5% and correct operation up to approximately 55 GHz were experimentally demonstrated. The results indicate that double switching, traditionally regarded as undesirable in SFQ circuit design, can instead be harnessed as a useful primitive for compact SFQ logic circuits.
Abstract Single-flux-quantum (SFQ) circuits are promising candidates for post-Moore integrated circuits owing to their ultra-high-speed operation and low power consumption. However, limitations in current superconducting fabrication processes pose significant challenges to achieving area-efficient SFQ-based microprocessors, particularly in the design of compact arithmetic logic units (ALUs). Unary computing enables arithmetic operations using extremely simple logic, but typically suffers from long computation latency. This paper focuses on unary computing for superconducting circuits that exploits the complementary characteristics of SFQ logic and unary computing. The ultra-high-speed nature of SFQ circuits compensates for the inherent latency of unary computation, while unary computing enables an ultra-low hardware cost by substantially reducing circuit complexity. Based on this concept, we introduce a unary computing methodology tailored for SFQ circuits and design a superconducting unary ALU with ultra-low hardware cost. The proposed ALU requires only 183 Josephson junctions (JJs), achieving approximately 88.2% reduction in JJ count and 80.4% reduction in area compared with a conventional bit-serial SFQ ALU. The proposed design, including binary-to-unary and unary-to-binary converters, was fabricated using a 10 kA cm −2 Nb four-layer superconducting circuit fabrication process and experimentally verified to operate correctly at approximately 72 GHz. The total power consumption at this frequency is approximately 58.9 µ W. This work quantitatively demonstrates the effectiveness of combining unary computing with SFQ circuits for ultra-low-cost processing systems and provides superconducting circuits as a new design option for alternative computation paradigms, such as unary computing.
Large-scale integration of single flux quantum (SFQ) circuits requires components as compact as possible. In this paper, we study the feasibility of integrating vertically stacked Josephson inductors (VSJIs) fabricated with self-shunted Josephson junctions into our SFQ-based circuits, and use both dc and RF electrical measurements to verify the performance of these junction stacks as compact inductors. The VSJIs consist of three Josephson junctions stacked vertically and are inserted into test structures to validate their potential as compact alternatives to geometrical inductors. The VSJIs are designed to be non-switching junctions and are combined with smaller area, switching Josephson junctions fabricated with the same junction barrier process. The VSJIs have a designed critical current of approximately 50% greater than that of the switching junctions, and their observed behavior can be modeled correctly by including the known nonlinearity of the Josephson inductance. To confirm that this nonlinearity does not degrade the expected bias margins, we simulate two common types of SFQ cells with the geometrical inductors replaced by VSJIs. The results verify that incorporating VSJIs in SFQ circuits would increase circuit density with minimal impact on circuit margins.
We designed several single flux quantum (SFQ) flip-flops and logic gates composed of Josephson junctions (JJs) and π-shifted JJs (π-JJs) to quantitatively evaluate effectiveness of introduction of π-JJs into the SFQ logic circuit. One-output flip-flops and logic gates were designed on the basis of the circuit design methodology we built for the SFQ circuit containing π-JJs. The designed flip-flops and logic gates have wide operating margins, the dc-bias margins of larger than ±30%, and device parameter margins of ±18%, though the static power consumption are reduced compared to conventional ones composed of JJs. We found that the difference in the critical current density between JJs and π-JJs does not affect the operating margins of the SFQ flip-flop composed of JJs and π-JJs. We devised a circuit structure of the delay flip-flop with complementary outputs composed of JJs and π-JJs (π-DFFC). The analog circuit simulation shows the dc-bias margin of the π-DFFC is larger than ±33%. These results indicate that the large-scale SFQ logic circuit system can be implemented using the flip-flops and logic gates containing π-JJs.
Abstract Superconducting single flux quantum (SFQ) circuits can operate at ultrafast speeds, and their superconducting random number generators (SRNGs) produce high-quality stochastic bit sequences at several tens GHz, with an arbitrary probability of outputting ‘1’, making them ideal for stochastic computing. The conventional superconducting stochastic adder uses a multiplexer (MUX) controlled by a random bit sequence generated by the SRNG. However, the SFQ-based MUX occupies a large circuit area, and any deviation in the probability of the control signal directly degrades the accuracy of stochastic addition. To overcome these limitations, we propose a deterministic stochastic adder comprising only an AND gate, an XOR gate, and a toggle flip-flop. Our design outputs one ‘1’ for every two input ‘1’s, achieving stochastic addition without the random control signal. Compared to the MUX-based stochastic adder, the proposed adder reduces the root-mean-square error by a factor of 32 when adding 1024-bit random sequences, reduces circuit area by 49.0%, and Josephson junction count by 28.1%, while supporting operating frequencies of about 120 GHz in simulation. We fabricated the proposed adder with two SRNGs for generating input sequences using a 10 kA cm −2 Nb four-layer superconducting process. High-speed operation was verified up to approximately 35.4 GHz with a constant bias margin by measuring the average voltage at the input and outputs. To the best of our knowledge, this is the first demonstration of ultrafast stochastic arithmetic operations above 30 GHz.
A methodology for designing single-flux-quantum (SFQ) flip-flops composed of both conventional (0-) and π -shifted Josephson junctions is investigated. We investigated the implementation of a storage loop, which can store flux quantum and is indispensable to express binary logic states in superconductor logic circuits. As all SFQ flip-flops have storage loops, the investigated design methodology can be applied to their design. We designed several SFQ flip-flops composed of 0- and π -shifted Josephson junctions using the investigated design methodology. The performances of the designed SFQ flip-flops were quantitatively evaluated by using an analog circuit simulator which we developed. We confirmed the correct operation of various SFQ flip-flops composed of 0- and π -shifted Josephson junctions with wide operating margins. Moreover, we observed that the investigated design methodology is suitable for SFQ flip-flops with complementary outputs because a storage loop composed of both 0- and π -shifted Josephson junctions has a symmetric structure and the complementary output function can be realized by using the storage loop. Our investigation indicates that the number of Josephson junctions and static power consumption of a non-destructive read-out flip-flop with complementary outputs (NDROC) can be reduced to less than half of those of the conventional NDROC, which has two storage loops composed of 0-Josephson junctions, to realize the complementary output function. The investigated design methodology is expected to be applied to not only SFQ circuits but also other superconducting logic circuits and novel reconfigurable logic devices using programmable 0- π Josephson junctions.
Due to their high-speed operation and low power consumption, single flux quantum (SFQ) circuits are promising technologies for integrated circuits. However, current superconducting fabrication limitations impose strict area constraints, challenging the construction of large-scale systems. Unary computing (UC) encodes numerical values by concentrating all “1”s at the beginning of a bit sequence. This approach enables arithmetic operations with fewer logic gates, thereby improving the area efficiency. In this study, we propose a novel high-capacity D flip-flop (HC-DFF) cell for UC-based SFQ circuits that achieves high-density data registration while preserving UC encoding. The HC-DFF employs a cascaded storage loop structure in which each loop sequentially stores one flux quantum, avoiding the margin deterioration associated with storing multiple flux quanta in a single loop. Simulation shows that the proposed HC-DFF achieves a bias margin of –20.8% to +32.7% and supports read/write operations above 100 GHz. We fabricated the HC-DFF using a 10 kA/cm² Nb four-layer superconducting process and verified its operation through low-speed measurements. The HC-DFF offers enhanced scalability and stability while reducing the number of required Josephson junctions by 83.3% per bit compared to conventional DFF-based shift registers for saving UC signals. For short unary sequences of less than 31 bits, it retains an advantage over storing binary data with equivalent precision using conventional DFF-based shift registers.