Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

AIP Advances

Dynamic control of a narrow-line red magneto-optical trap for strontium atoms under microgravity

Jie Ren, Chihua Zhou, Benquan Lu, Wei Tan, XIA Jian, Guodong Zhao, Hongxin Zou, Hong Chang

Published Aug 1, 2026• 1 citation
Publisher

Abstract

The microgravity environment modifies the resonance condition that is formed with the participation of gravity in the 689 nm narrow-line magneto-optical trap (red MOT) of a ground-based strontium optical clock. Consequently, a cooling scheme optimized under standard 1g ground-commissioning conditions cannot be directly transferred to an in-orbit space optical clock. In this work, we establish a one-dimensional semiclassical Monte Carlo stochastic dynamics model along the ground-gravity direction to study the cooling dynamics, spatial distribution, and position compensation of a 88Sr narrow-line MOT under microgravity. The simulations show that directly applying ground-optimized parameters in microgravity leads to heating, cloud broadening, and displacement from the lattice position calibrated on the ground. Reducing the detuning can produce a smaller spatial distribution, but this behavior is mainly phase-space truncation and cannot maintain a sufficient effective atom number. We propose a dynamic-control scheme in which the laser detuning and intensity are continuously ramped, achieving an atomic temperature below 3 μK under microgravity while retaining more than 98% of the atoms in the MOT, outperforming the 1g ground-gravity reference case. On this basis, magnetic-gradient screening is used to obtain a cloud size matched to the optical-lattice mode. After an additional compensation magnetic field is introduced, the deviation between the narrow-line MOT center and the lattice position is ∼2.4 μm, far smaller than the transverse scale of the lattice beam. These results provide a physical picture and theoretical guidance for in-orbit commissioning of the narrow-line MOT in a strontium optical clock on the Chinese Space Station.

DOI
10.1063/5.0346328

Related papers

Analysis of Narrow-Line Laser Cooling and Trapping of Sr Atoms in Microgravity Environments

Jie Ren, Hui Liu, Xiaotong Lu +1 more

Obtaining ultracold alkaline earth(-like) atoms in space encounters the problem of performing narrow-line laser cooling in microgravity environments ( μ -gEs). This paper reports an analysis of the magneto-optical trap (MOT) based on the narrow-line transition in 88 Sr, while paying special attention to the role of the gravity. This analysis suggests the MOTs based on narrow-line transitions cannot be cold and dense enough in a μ -gE. We thus propose a strategy: that one can use a dual-frequency MOT to realize a low-temperature, high density, and high transfer efficiency, narrow-line red MOT in μ -gEs.

Applied Sciences•Jul 17, 2020•5 citations

Narrow Line Cooling of 88Sr Atoms in the Magneto-optical Trap for Precision Frequency Standard

S A Strelkin, A. A. Galyshev, O I Berdasov +5 more

We report on our progress toward the realization of a Strontium optical lattice clock, which is under development at VNIIFTRI as a part of GLONASS program. We’ve prepared the narrow line width laser system for secondary cooling of 88Sr atoms which allows us to reach atom cloud temperature below 3 μK after second cooling stage.

Physics Procedia•Jan 1, 2015•4 citations

Magneto-Optical Trapping of 88 Sr atoms with 689 nm Laser

Qiang Wang, Bai-Ke Lin, Yang Chun Zhao +6 more

We report the experimental realization of strontium magneto-optical trap (MOT) operating on the intercombination transition 1 S 0 − 3 P 1 at 689 nm, namely red MOT. A 689 nm laser used for cooling and trapping is injection locked to a master laser, whose linewidth is narrowed to 150 Hz by locking to a high finesse optical reference cavity. 88 Sr atoms pre-cooled and trapped by the broad 1 S 0 − 1 P 1 transition at 461 nm are transferred to the red MOT with the help of a time sequence controller. The transfer ratio is about 20% and the red MOT's temperature is estimated to be less than 20 μK by the time-of-flight (TOF) image analysis.

Chinese Physics Letters•Mar 1, 2011•11 citations

Towards miniaturized strontium optical lattice clock

Wei He

Optical atomic clocks with precisions and accuracies in the \n10\\(^-\\)\\(^1\\)\\(^8\\) level [1] are now the most advanced man-made timekeeping devices. They outperform the microwave cesium atomic clocks that realize the SI definition of the second. Scaling down the size of optical atomic clocks may open the door to a range of industrial and space applications. \n \nIn this thesis, the design and preliminary results of a compact strontium cooling system are presented. In the first cooling stage, the high power 461 nm laser with 300 mW output features a modular design, while smaller laser sources for demonstrating a strontium magneto-optical trap have also been investigated. An innovative design that couples a spectroscopy cell directly into the scientific chamber reduces the overall size and power consumption of the system. Additionally, using strontium oxide as a source of strontium atoms suitable for optical clocks has achieved initial success. For the first time, a single-beam MOT configuration is applied to strontium. In this novel apparatus, the blue MOT and red MOT broadband cooling phases are able to trap 5x10\\(^6\\) and 1000 atoms, respectively. This work shows promising progress towards developing a functional miniaturized strontium optical lattice clock.

•Jul 1, 2017•5 citations

Loading, cooling and trapping of Strontium using intercombinaison line

T. Chanelière, Ling Xiang He, Robin Kaiser +1 more

The intercombination line of Strontium at 689nm is successfully used in laser cooling to reach the photon recoil limit with Doppler cooling in a magneto-optical traps (MOT). In this paper we present a systematic study of the loading efficiency of such a MOT. Comparing the experimental results to a simple model allows us to discuss the actual limitation of our apparatus. We also study in detail the final MOT regime emphasizing the role of gravity on the position, size and temperature along the vertical and horizontal directions. At large laser detuning, one finds an unusual situation where cooling and trapping occur in the presence of a high bias magnetic field.

•Apr 6, 2007•0 citations

Optimization of the loading rate of magneto-optical trap for neutral mercury atom

Gou Wei, Kangkang Liu, 付小虎 Fu Xiaohu +3 more

Optics lattice clock is a hot topic in the researches of frequency standard and metrology. Neutral mercury atom is one of the most promising candidates for optical lattice clock. Due to its large atomic number, mercury atom is insensitive to black body radiation, which is the severe limitation for developing the optical lattice clocks. To realize the optical lattice clock of neutral mercury atoms, the first step is to implement laser-cooling and trapping of neutral mercury atoms. The cooling transition of mercury atom is 1S0-3P1 transition. The wavelength is 253.7 nm, the line width is 1.27 MHz, and the saturation intensity is 10.2 mW/cm2. Quantum projection noise (QPN) is an important parameter that affects optical lattice clock. Increasing the loading rate of magneto-optical trap (MOT) can help lower the QPN, thereby improving the performance of optical lattice clock. In this work, we calculate the scattering force of deep UV cooling laser, which is exerted on mercury atom in our single chamber MOT, and numerically simulate the one-dimensional motion of the atom in the MOT. It gives us the capture velocity under optimized parameters of the MOT. Then we calculate the loading rate of three-dimensional MOT by a high efficient random sampling method. According to the rate equation of MOT, the loading rate is proportional to the atom number of the steady state, which is the accessible parameter in the experiment. An experimental setup of MOT is established with a high vacuum system and a frequency quadrupled semiconductor laser system. The fluorescence imaging on an EMCCD gives the atom number in the MOT. We also calibrate the vapor density of background mercury gas in the vacuum, and measure the atom number in a steady MOT. We numerically simulate and experimentally study the influences on the atom number on the parameters of MOT, such as laser intensity, laser detuning and magnetic field gradient. The calculated results are in consistent with the experimental results. We also find the optimized parameters to maximize the loading rate. The numerical simulation also gives some results beyond current experimental condition, especially for laser intensity. From the simulations we obtain the optimized MOT parameter and relation for laser cooling of neutral mercury atom. Especially, current deep UV cooling laser with 20 mW of power does not have enough power to enhance the loading rate. These results are rather valuable for designing the next generation of optical lattice clocks for neutral mercury atoms.

Acta Physica Sinica•Jan 1, 2016•4 citations
The microgravity environment modifies the resonance condition that is formed with the participation of gravity in the 689 nm narrow-line magneto-optical trap (red MOT) of a ground-based strontium optical clock. Consequently, a cooling scheme optimized under standard 1g ground-commissioning conditions cannot be directly transferred to an in-orbit space optical clock. In this work, we establish a one-dimensional semiclassical Monte Carlo stochastic dynamics model along the ground-gravity direction to study the cooling dynamics, spatial distribution, and position compensation of a 88Sr narrow-line MOT under microgravity. The simulations show that directly applying ground-optimized parameters in microgravity leads to heating, cloud broadening, and displacement from the lattice position calibrated on the ground. Reducing the detuning can produce a smaller spatial distribution, but this behavior is mainly phase-space truncation and cannot maintain a sufficient effective atom number. We propose a dynamic-control scheme in which the laser detuning and intensity are continuously ramped, achieving an atomic temperature below 3 μK under microgravity while retaining more than 98% of the atoms in the MOT, outperforming the 1g ground-gravity reference case. On this basis, magnetic-gradient screening is used to obtain a cloud size matched to the optical-lattice mode. After an additional compensation magnetic field is introduced, the deviation between the narrow-line MOT center and the lattice position is ∼2.4 μm, far smaller than the transverse scale of the lattice beam. These results provide a physical picture and theoretical guidance for in-orbit commissioning of the narrow-line MOT in a strontium optical clock on the Chinese Space Station.
Obtaining ultracold alkaline earth(-like) atoms in space encounters the problem of performing narrow-line laser cooling in microgravity environments ( μ -gEs). This paper reports an analysis of the magneto-optical trap (MOT) based on the narrow-line transition in 88 Sr, while paying special attention to the role of the gravity. This analysis suggests the MOTs based on narrow-line transitions cannot be cold and dense enough in a μ -gE. We thus propose a strategy: that one can use a dual-frequency MOT to realize a low-temperature, high density, and high transfer efficiency, narrow-line red MOT in μ -gEs.
We report the experimental realization of strontium magneto-optical trap (MOT) operating on the intercombination transition 1 S 0 − 3 P 1 at 689 nm, namely red MOT. A 689 nm laser used for cooling and trapping is injection locked to a master laser, whose linewidth is narrowed to 150 Hz by locking to a high finesse optical reference cavity. 88 Sr atoms pre-cooled and trapped by the broad 1 S 0 − 1 P 1 transition at 461 nm are transferred to the red MOT with the help of a time sequence controller. The transfer ratio is about 20% and the red MOT's temperature is estimated to be less than 20 μK by the time-of-flight (TOF) image analysis.
Optical atomic clocks with precisions and accuracies in the \n10\\(^-\\)\\(^1\\)\\(^8\\) level [1] are now the most advanced man-made timekeeping devices. They outperform the microwave cesium atomic clocks that realize the SI definition of the second. Scaling down the size of optical atomic clocks may open the door to a range of industrial and space applications. \n \nIn this thesis, the design and preliminary results of a compact strontium cooling system are presented. In the first cooling stage, the high power 461 nm laser with 300 mW output features a modular design, while smaller laser sources for demonstrating a strontium magneto-optical trap have also been investigated. An innovative design that couples a spectroscopy cell directly into the scientific chamber reduces the overall size and power consumption of the system. Additionally, using strontium oxide as a source of strontium atoms suitable for optical clocks has achieved initial success. For the first time, a single-beam MOT configuration is applied to strontium. In this novel apparatus, the blue MOT and red MOT broadband cooling phases are able to trap 5x10\\(^6\\) and 1000 atoms, respectively. This work shows promising progress towards developing a functional miniaturized strontium optical lattice clock.
The intercombination line of Strontium at 689nm is successfully used in laser cooling to reach the photon recoil limit with Doppler cooling in a magneto-optical traps (MOT). In this paper we present a systematic study of the loading efficiency of such a MOT. Comparing the experimental results to a simple model allows us to discuss the actual limitation of our apparatus. We also study in detail the final MOT regime emphasizing the role of gravity on the position, size and temperature along the vertical and horizontal directions. At large laser detuning, one finds an unusual situation where cooling and trapping occur in the presence of a high bias magnetic field.
Optics lattice clock is a hot topic in the researches of frequency standard and metrology. Neutral mercury atom is one of the most promising candidates for optical lattice clock. Due to its large atomic number, mercury atom is insensitive to black body radiation, which is the severe limitation for developing the optical lattice clocks. To realize the optical lattice clock of neutral mercury atoms, the first step is to implement laser-cooling and trapping of neutral mercury atoms. The cooling transition of mercury atom is 1S0-3P1 transition. The wavelength is 253.7 nm, the line width is 1.27 MHz, and the saturation intensity is 10.2 mW/cm2. Quantum projection noise (QPN) is an important parameter that affects optical lattice clock. Increasing the loading rate of magneto-optical trap (MOT) can help lower the QPN, thereby improving the performance of optical lattice clock. In this work, we calculate the scattering force of deep UV cooling laser, which is exerted on mercury atom in our single chamber MOT, and numerically simulate the one-dimensional motion of the atom in the MOT. It gives us the capture velocity under optimized parameters of the MOT. Then we calculate the loading rate of three-dimensional MOT by a high efficient random sampling method. According to the rate equation of MOT, the loading rate is proportional to the atom number of the steady state, which is the accessible parameter in the experiment. An experimental setup of MOT is established with a high vacuum system and a frequency quadrupled semiconductor laser system. The fluorescence imaging on an EMCCD gives the atom number in the MOT. We also calibrate the vapor density of background mercury gas in the vacuum, and measure the atom number in a steady MOT. We numerically simulate and experimentally study the influences on the atom number on the parameters of MOT, such as laser intensity, laser detuning and magnetic field gradient. The calculated results are in consistent with the experimental results. We also find the optimized parameters to maximize the loading rate. The numerical simulation also gives some results beyond current experimental condition, especially for laser intensity. From the simulations we obtain the optimized MOT parameter and relation for laser cooling of neutral mercury atom. Especially, current deep UV cooling laser with 20 mW of power does not have enough power to enhance the loading rate. These results are rather valuable for designing the next generation of optical lattice clocks for neutral mercury atoms.