Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

TiN 및 Al 박막의 초전도 길이 척도에 대한 정량적 특성 분석 및 양자 소자 응용으로의 고찰

김성훈

Published Jan 1, 2026• 0 citations
OpenAlex

Abstract

Although advances in circuit design and quantum control have improved the coherence of superconducting quantum circuits, microwave losses arising from the intrinsic properties of constituent materials remain a primary limitation. Identifying and understanding these decoherence mechanisms requires research at the material level, which in turn requires the development of precise measurement techniques and quantitative analysis of superconducting thin films. This thesis introduces an experimental framework for characterizing basic superconducting length scales, specifically the superconducting coherence length and the London penetration depth. The superconductivity of titanium nitride (TiN) thin films was investigated using upper critical field measurements. Analysis of the pronounced anisotropy between the in-plane and out-of-plane critical fields, along with the observed temperature-dependent dimensional crossover, indicates that superconductivity is confined to an effective thickness that is even smaller than the nominal value. These results provide quantitative evidence for the presence of an interfacial dead layer in which the superconductivity is strongly suppressed. Furthermore, this transport-based analysis suggests that it can serve as a non-destructive method for evaluating interface quality and effective superconducting volume in disordered systems. To measure the London penetration depth, a key parameter for characterizing and exploring superconductivity, the electrodynamic response of superconducting films was examined using the two-coil mutual inductance technique (TCMI). Aluminum thin films served as a standard system to validate both the experimental setup and the numerical inversion code. The measured temperature dependence of the penetration depth aligns with conventional s-wave BCS theory, yielding a zero-temperature penetration depth λ(0) of 45 nm, consistent with well-known bulk values. These methodologies enable high-throughput characterization, which is essential for optimizing superconducting films for quantum circuits. Moreover, this capability allows a systematic separation of geometry-dependent circuit effects from intrinsic material-loss mechanisms. This distinction provides a practical pathway toward improving coherence by addressing material limitations at their origin.

Related papers

Inductance and penetration depth measurements of polycrystalline NbN films for all-NbN single flux quantum circuits

Yulong Zhong, Lu Zhang, Junjie Xie +9 more

Abstract In this paper, we report on a systematic study of the inductance and magnetic field penetration depth (λ) of polycrystalline NbN superconducting thin films. By employing a four-metal-layer fabrication process specifically designed for all-NbN single-flux-quantum circuits, we constructed a superconducting quantum interference device loop composed of two parallel NbN SNS junctions, NbN microstrips, and NbN ground planes for precise inductance measurement. At 4.2 K, as the linewidth increases from 1 μm to 30 μm, the inductance per unit length (L u) of NbN microstrips significantly decreases, for example, the L u of 250 nm thick NbN microstrips drops from 0.907 pH/μm to 0.047 pH/μm. Compared to Nb, the L u of polycrystalline NbN microstrips is approximately two to three times that of Nb, offering an advantage for manufacturing smaller superconducting inductors. Furthermore, we conducted simulation analysis using InductEx software to extract the λ of NbN films of varying thicknesses. The results indicate that as the film thickness increased from 45 nm to 600 nm, λ initially decreased sharply and then stabilized, with values ranging from 430 nm to 323 nm. Notably, once the film thickness exceeded 200 nm, λ remained essentially constant, even at a temperature of 10 K, where it showed good stability, albeit with a slight increase (about 50 nm) compared to 4.2 K. This dependence of λ on thickness is reasonably explained by considering the effects of NbN film thickness on the superconducting critical temperature and residual resistivity. These research findings not only deepen our understanding of the characteristics of superconducting films but also lay a solid foundation for the future design and manufacture of more compact superconducting circuits at the higher temperature of 10 K.

Superconductor Science and Technology•Nov 18, 2024•3 citations

Growth of titanium-nitride thin films for low-loss superconducting quantum circuits

Gustaf Olson

This is a study of the growth of titanium-nitride (TiN) by plasma assisted molecular beam epitaxy (MBE) for applications in low loss quantum circuits. Titanium nitride is a material known to have low loss at microwave frequencies which sees practical use in many emerging quantum device architectures. The goal of this research is to investigate improvements in TiN thin films utilizing MBE to produce highly pure, highly crystalline films. A review of the theory of superconducting qubits is given and recent developments in superconducting qubit research are summarized to elucidate how loss has been reduced historically and the importance of materials improvements to the future of scalable quantum computation. The dynamics of epitaxial film growth are discussed, focusing on the formation of a minimum energy surface, the thermally driven kinetics of atoms deposited on the surface, and how these lead to the formation of large scale crystalline domains in the film. An overview of the MBE growth chamber is given and the growth procedure for TiN is discussed. Transport and morphology measurement results are discussed for MBE TiN where, for optimized growth conditions, films are highly crystalline with superconducting transition temperatures(Tc) as high as Tc = 6.1K, matching the value for bulk crystals and exceeding all reported thin film values. Microwave loss measurements of transmission line resonators fabricated from these films are shown to have low-power quality factors(Q) as high as 200,000 and an increase to Q = 400,000 at high power, consistent with the saturation of two-level-systems (TLS) at high power. These results confirm a connection between the high quality crystalline materials produced in this work and low loss in quantum circuits.

•May 29, 2015•3 citations

Absolute measurement of penetration depth of superconducting thin films using microwave stripline resonators

Arghya Dutta, Ajeet Salunke, Mahesh Poojary +3 more

Superconducting microstrip resonators, which leverage kinetic inductance to probe electrodynamics, are sensitive tools for studying superconducting thin films at microwave frequencies. However, extracting the absolute superconducting penetration depth from these measurements remains challenging. In this work, we present a hybrid method to determine the absolute value of penetration depth over a wide temperature range by combining resonator measurements with finite-element electromagnetic simulations in COMSOL Multiphysics. We demonstrate this approach by extracting the penetration depth of NbN films by fabricating resonators from films of various thicknesses. Furthermore, we extend the technique to materials with lower critical temperatures by employing a flip-film geometry. By placing a sample above a NbN resonator, separated by a thin Mylar dielectric, we create a coupled structure where changes in the sample's penetration depth shift the resonant frequency. This non-destructive method provides a reliable, high-sensitivity platform for characterizing the penetration depth of diverse superconducting thin films.

arXiv:2605.28759•May 27, 2026•0 citations

Optimizing CMOS-compatible, superconducting titanium nitride resonators: Deposition conditions and structuring processes

Simon J. K. Lang, Alexandra Schewski, Ignaz Eisele +10 more

We report on the fabrication and characterization of superconducting coplanar waveguide (CPW) resonators based on titanium nitride (TiN) thin films deposited on 200\,mm diameter high-resistivity Si(100) substrates. We systematically investigate how deposition conditions, dry-etch power and in-situ resist strip temperature affect morphology, superconducting properties and dielectric losses. By tuning reactive sputtering conditions, three distinct preferred out-of-plane crystal orientations - (111), (200), and a mix of both are achieved. Our results demonstrate that all films exhibit similar minimal two-level system (TLS) losses, with TiN111 exhibiting the lowest median TLS losses $\tildeδ_\mathrm{TLS}$, and greater robustness against reoxidation. The applied structuring process, in contrast, has a far greater influence on the TLS loss than the crystal orientation of the TiN film and, consequently, the intrinsic material properties of the superconducting layer. The lowest TLS losses for all TiN depositions were achieved with a low power etch and low temperature resist strip. An additional buffered oxide etch (BOE) treatment could remove high-loss interfacial oxides at the metal-air (MA) and substrate-air (SA) interface and recover the etch-induced TLS losses. Consequently, TiN resonators exhibiting $\tildeδ_\mathrm{TLS}$ values as low as $9.67 \times 10^{-7}$ were realized. The corresponding median low-power loss, $\tildeδ_\mathrm{LP}$, amounts to $11.04 \times 10^{-7}$, which translates to an internal quality factor approaching one million. These findings highlight the critical role of process induced oxide formation at the MA and SA interfaces in limiting the performance of TiN resonators and provide a scalable, low-loss process compatible with industry-grade 200\,mm CMOS qubit fabrication workflows.

quant-pharXiv:2603.00441•Applied Physics Reviews•Mar 3, 2026•2 citations

Superconducting thin films and hybrid materials for quantum devices

Sjoerd Telkamp

The performance and coherence of superconducting quantum systems are fundamentally tied to the quality of the materials from which they are built. In superconducting transmon qubits, many loss mechanisms and sources of decoherence originate from material imperfections or unwanted oxide formation. Likewise, semiconductor–superconductor hybrid systems depend on high-quality interfaces to ensure strong coupling between electronic states in the two materials. In such hybrid devices, the accessible operating regime is often dictated by the intrinsic material properties of either the semiconductor or the superconductor. Advancing quantum device performance therefore requires exploring new material systems and optimizing their physical characteristics. In this thesis, we present the development of several superconducting material platforms for quantum technologies, including superconducting qubits, single-photon detectors, and semiconductor superconductor hybrid devices. We focus on the growth and characterization of superconducting films and heterostructures, and we establish clear connections between their material properties and the resulting device performance. First, we will present a novel semiconductor-superconductor hybrid material based on in-situ deposited epitaxial layers of Nb and Al on a shallow InAs quantum well. In this structure, the Al interlayer provides an epitaxial connection between an in-situ magnetron sputtered Nb or NbTi thin film and a shallow InAs two dimensional electron gas. This metal-to-metal epitaxy is achieved by optimization of the material stack and results in an induced superconducting gap of approximately 1 meV, determined from transport measurements of superconductor semiconductor Josephson junctions. This induced gap is approximately five times larger than the values reported for Al-based hybrid materials and indicates the formation of highly-transparent interfaces that are required in high-quality hybrid material platforms. Then, we discuss a different approach in the next chapter where we develop a hybrid material based on a molecular beam epitaxy grown InAsSb surface quantum well with an in-situ deposited Nb layer directly on top of the quantum well. Relative to conventional Al-InAs based systems, the InAsSb surface quantum well offers a lower effective mass and stronger spin-orbit interaction, while the Nb layer has a higher critical temperature and a larger critical magnetic field. The in-situ deposition of the Nb layer directly on top of the quantum well results in a high-quality interface that enables strong coupling to the InAsSb quantum well. Transport measurements on Josephson junctions reveal an induced superconducting gap of 1.3 meV and a critical current density of 3.75 × 10³A/cm². Furthermore, a planar asymmetric SQUID is realized, exhibiting gate-tunable superimposed oscillations originating from both the individual Josephson junction and the full SQUID loop. The large induced superconducting gap combined with strong spin-orbit interaction position this material as an attractive platform for experiments exploring gate-tunable superconductivity and topological superconducting devices. In the next chapter, we will focus on establishing a link between Nb film crystal properties and their performance in superconducting circuits. In this study, we investigate the microwave properties of niobium resonators with different crystalline properties and related surface topographies. We analyze a series of magnetron sputtered films in which the Nb crystal orientation and surface topography are changed by varying the substrate temperatures between room temperature and 975 K. The lowest-loss resonators that we measure have quality factors of over 10⁶ at single-photon powers, among the best ever recorded using the Nb on sapphire platform. We observe the highest quality factors in films grown at an intermediate temperature regime of the growth series (550 K) where the films display both preferential ordering of the crystal domains and low surface roughness. Furthermore, we analyze the temperature-dependent behavior of our resonators to learn about how the quasi-particle density in the Nb film is affected by the niobium crystal structure and the presence of grain boundaries. Then, we explore yet a different material platform by attempting to realize onchip NbTiN single photon detectors on LiNbO₃, an emerging photonic platform with high potential for scalable quantum information processing. We use DC reactive magnetron sputtering to grow high-quality NbTiN thin films and investigate the impact of substrate temperature during NbTiN growth. We achieve four nm thick superconducting films with a critical temperature (𝑇𝑐) of 12.3 K grown at a substrate temperature of 825 K. We demonstrate that the increased substrate temperature reduces the oxygen concentration in our films and improves the overall stoichiometry. In addition, we integrate these films with the LiNbO3 platform and investigate the obtained interface quality. Finally, we fabricate superconducting nanowire single photon detectors from the NbTiN film on LiNbO₃ and characterize the detector performance. Lastly, we report a gate-tunable Josephson diode effect in hybrid nanowire junctions consisting of a spin-orbit-coupled semiconductor core coated with epitaxial ferromagnetic insulator and superconductor shells. The wires display a hysteretic superconducting window as a function of axial magnetic field. In the superconducting regime, the devices exhibit nonreciprocal current transport, with the diode efficiency showing a strong dependence on back-gate voltage. The effect persists in a remanent magnetization state following a controlled demagnetization procedure, establishing zero-field operation. The combination of results presented in this thesis stress the importance of a material-focused approach in advancing the performance of quantum hardware. The novel hybrid material platforms developed in this thesis expand the operating regime of devices, which could enable future experiments involving gate-tunable superconductivity or topological properties. Similarly, we demonstrate that optimizing superconductor crystal structure benefits quantum devices, such as single-photon detectors and superconducting resonators.

•Jan 1, 2026•0 citations

Microwave and superconducting techniques for measurements on unconventional Josephson junctions

Georgina M. Klemencic

The frst part of the thesis describes the instrumentation, testing and analysis of a planar circuit designed for the measurement of the current-phase relationship of niobium-cobalt-insulator-niobium Josephson junctions. A detailed analysis method and fitting routine was developed but the results show that an irreducible mutual inductance places a limit on the accuracy of the chip for the intended measurement. The second part describes a study of the magnetic and microwave properties of a range of thin film niobium coplanar resonators with cobalt and normal metal layers. Magnetic measurements show a magnetic dead layer of 1.3 nm. The observed microwave losses are found to be two orders of magnitude higher than for high quality niobium films. Computer simulation shows that this is mainly due to conductive, rather than magnetic losses, and is in good agreement with the observed proportionality to cobalt thickness. Measurements of the temperature and magnetic field dependence of the losses and resonant frequency as a function of the cobalt thickness show no signs of the oscillatory thickness dependence reported in a number of other experiments. The temperature dependence of all films is found to be in good agreement with Mattis-Bardeen theory.

•Jul 1, 2013•1 citation
Although advances in circuit design and quantum control have improved the coherence of superconducting quantum circuits, microwave losses arising from the intrinsic properties of constituent materials remain a primary limitation. Identifying and understanding these decoherence mechanisms requires research at the material level, which in turn requires the development of precise measurement techniques and quantitative analysis of superconducting thin films. This thesis introduces an experimental framework for characterizing basic superconducting length scales, specifically the superconducting coherence length and the London penetration depth. The superconductivity of titanium nitride (TiN) thin films was investigated using upper critical field measurements. Analysis of the pronounced anisotropy between the in-plane and out-of-plane critical fields, along with the observed temperature-dependent dimensional crossover, indicates that superconductivity is confined to an effective thickness that is even smaller than the nominal value. These results provide quantitative evidence for the presence of an interfacial dead layer in which the superconductivity is strongly suppressed. Furthermore, this transport-based analysis suggests that it can serve as a non-destructive method for evaluating interface quality and effective superconducting volume in disordered systems. To measure the London penetration depth, a key parameter for characterizing and exploring superconductivity, the electrodynamic response of superconducting films was examined using the two-coil mutual inductance technique (TCMI). Aluminum thin films served as a standard system to validate both the experimental setup and the numerical inversion code. The measured temperature dependence of the penetration depth aligns with conventional s-wave BCS theory, yielding a zero-temperature penetration depth λ(0) of 45 nm, consistent with well-known bulk values. These methodologies enable high-throughput characterization, which is essential for optimizing superconducting films for quantum circuits. Moreover, this capability allows a systematic separation of geometry-dependent circuit effects from intrinsic material-loss mechanisms. This distinction provides a practical pathway toward improving coherence by addressing material limitations at their origin.
Abstract In this paper, we report on a systematic study of the inductance and magnetic field penetration depth (λ) of polycrystalline NbN superconducting thin films. By employing a four-metal-layer fabrication process specifically designed for all-NbN single-flux-quantum circuits, we constructed a superconducting quantum interference device loop composed of two parallel NbN SNS junctions, NbN microstrips, and NbN ground planes for precise inductance measurement. At 4.2 K, as the linewidth increases from 1 μm to 30 μm, the inductance per unit length (L u) of NbN microstrips significantly decreases, for example, the L u of 250 nm thick NbN microstrips drops from 0.907 pH/μm to 0.047 pH/μm. Compared to Nb, the L u of polycrystalline NbN microstrips is approximately two to three times that of Nb, offering an advantage for manufacturing smaller superconducting inductors. Furthermore, we conducted simulation analysis using InductEx software to extract the λ of NbN films of varying thicknesses. The results indicate that as the film thickness increased from 45 nm to 600 nm, λ initially decreased sharply and then stabilized, with values ranging from 430 nm to 323 nm. Notably, once the film thickness exceeded 200 nm, λ remained essentially constant, even at a temperature of 10 K, where it showed good stability, albeit with a slight increase (about 50 nm) compared to 4.2 K. This dependence of λ on thickness is reasonably explained by considering the effects of NbN film thickness on the superconducting critical temperature and residual resistivity. These research findings not only deepen our understanding of the characteristics of superconducting films but also lay a solid foundation for the future design and manufacture of more compact superconducting circuits at the higher temperature of 10 K.
This is a study of the growth of titanium-nitride (TiN) by plasma assisted molecular beam epitaxy (MBE) for applications in low loss quantum circuits. Titanium nitride is a material known to have low loss at microwave frequencies which sees practical use in many emerging quantum device architectures. The goal of this research is to investigate improvements in TiN thin films utilizing MBE to produce highly pure, highly crystalline films. A review of the theory of superconducting qubits is given and recent developments in superconducting qubit research are summarized to elucidate how loss has been reduced historically and the importance of materials improvements to the future of scalable quantum computation. The dynamics of epitaxial film growth are discussed, focusing on the formation of a minimum energy surface, the thermally driven kinetics of atoms deposited on the surface, and how these lead to the formation of large scale crystalline domains in the film. An overview of the MBE growth chamber is given and the growth procedure for TiN is discussed. Transport and morphology measurement results are discussed for MBE TiN where, for optimized growth conditions, films are highly crystalline with superconducting transition temperatures(Tc) as high as Tc = 6.1K, matching the value for bulk crystals and exceeding all reported thin film values. Microwave loss measurements of transmission line resonators fabricated from these films are shown to have low-power quality factors(Q) as high as 200,000 and an increase to Q = 400,000 at high power, consistent with the saturation of two-level-systems (TLS) at high power. These results confirm a connection between the high quality crystalline materials produced in this work and low loss in quantum circuits.
Superconducting microstrip resonators, which leverage kinetic inductance to probe electrodynamics, are sensitive tools for studying superconducting thin films at microwave frequencies. However, extracting the absolute superconducting penetration depth from these measurements remains challenging. In this work, we present a hybrid method to determine the absolute value of penetration depth over a wide temperature range by combining resonator measurements with finite-element electromagnetic simulations in COMSOL Multiphysics. We demonstrate this approach by extracting the penetration depth of NbN films by fabricating resonators from films of various thicknesses. Furthermore, we extend the technique to materials with lower critical temperatures by employing a flip-film geometry. By placing a sample above a NbN resonator, separated by a thin Mylar dielectric, we create a coupled structure where changes in the sample's penetration depth shift the resonant frequency. This non-destructive method provides a reliable, high-sensitivity platform for characterizing the penetration depth of diverse superconducting thin films.
We report on the fabrication and characterization of superconducting coplanar waveguide (CPW) resonators based on titanium nitride (TiN) thin films deposited on 200\,mm diameter high-resistivity Si(100) substrates. We systematically investigate how deposition conditions, dry-etch power and in-situ resist strip temperature affect morphology, superconducting properties and dielectric losses. By tuning reactive sputtering conditions, three distinct preferred out-of-plane crystal orientations - (111), (200), and a mix of both are achieved. Our results demonstrate that all films exhibit similar minimal two-level system (TLS) losses, with TiN111 exhibiting the lowest median TLS losses δ~TLS\tildeδ_\mathrm{TLS}δ~TLS​, and greater robustness against reoxidation. The applied structuring process, in contrast, has a far greater influence on the TLS loss than the crystal orientation of the TiN film and, consequently, the intrinsic material properties of the superconducting layer. The lowest TLS losses for all TiN depositions were achieved with a low power etch and low temperature resist strip. An additional buffered oxide etch (BOE) treatment could remove high-loss interfacial oxides at the metal-air (MA) and substrate-air (SA) interface and recover the etch-induced TLS losses. Consequently, TiN resonators exhibiting δ~TLS\tildeδ_\mathrm{TLS}δ~TLS​ values as low as 9.67×10−79.67 \times 10^{-7}9.67×10−7 were realized. The corresponding median low-power loss, δ~LP\tildeδ_\mathrm{LP}δ~LP​, amounts to 11.04×10−711.04 \times 10^{-7}11.04×10−7, which translates to an internal quality factor approaching one million. These findings highlight the critical role of process induced oxide formation at the MA and SA interfaces in limiting the performance of TiN resonators and provide a scalable, low-loss process compatible with industry-grade 200\,mm CMOS qubit fabrication workflows.
The performance and coherence of superconducting quantum systems are fundamentally tied to the quality of the materials from which they are built. In superconducting transmon qubits, many loss mechanisms and sources of decoherence originate from material imperfections or unwanted oxide formation. Likewise, semiconductor–superconductor hybrid systems depend on high-quality interfaces to ensure strong coupling between electronic states in the two materials. In such hybrid devices, the accessible operating regime is often dictated by the intrinsic material properties of either the semiconductor or the superconductor. Advancing quantum device performance therefore requires exploring new material systems and optimizing their physical characteristics. In this thesis, we present the development of several superconducting material platforms for quantum technologies, including superconducting qubits, single-photon detectors, and semiconductor superconductor hybrid devices. We focus on the growth and characterization of superconducting films and heterostructures, and we establish clear connections between their material properties and the resulting device performance. First, we will present a novel semiconductor-superconductor hybrid material based on in-situ deposited epitaxial layers of Nb and Al on a shallow InAs quantum well. In this structure, the Al interlayer provides an epitaxial connection between an in-situ magnetron sputtered Nb or NbTi thin film and a shallow InAs two dimensional electron gas. This metal-to-metal epitaxy is achieved by optimization of the material stack and results in an induced superconducting gap of approximately 1 meV, determined from transport measurements of superconductor semiconductor Josephson junctions. This induced gap is approximately five times larger than the values reported for Al-based hybrid materials and indicates the formation of highly-transparent interfaces that are required in high-quality hybrid material platforms. Then, we discuss a different approach in the next chapter where we develop a hybrid material based on a molecular beam epitaxy grown InAsSb surface quantum well with an in-situ deposited Nb layer directly on top of the quantum well. Relative to conventional Al-InAs based systems, the InAsSb surface quantum well offers a lower effective mass and stronger spin-orbit interaction, while the Nb layer has a higher critical temperature and a larger critical magnetic field. The in-situ deposition of the Nb layer directly on top of the quantum well results in a high-quality interface that enables strong coupling to the InAsSb quantum well. Transport measurements on Josephson junctions reveal an induced superconducting gap of 1.3 meV and a critical current density of 3.75 × 10³A/cm². Furthermore, a planar asymmetric SQUID is realized, exhibiting gate-tunable superimposed oscillations originating from both the individual Josephson junction and the full SQUID loop. The large induced superconducting gap combined with strong spin-orbit interaction position this material as an attractive platform for experiments exploring gate-tunable superconductivity and topological superconducting devices. In the next chapter, we will focus on establishing a link between Nb film crystal properties and their performance in superconducting circuits. In this study, we investigate the microwave properties of niobium resonators with different crystalline properties and related surface topographies. We analyze a series of magnetron sputtered films in which the Nb crystal orientation and surface topography are changed by varying the substrate temperatures between room temperature and 975 K. The lowest-loss resonators that we measure have quality factors of over 10⁶ at single-photon powers, among the best ever recorded using the Nb on sapphire platform. We observe the highest quality factors in films grown at an intermediate temperature regime of the growth series (550 K) where the films display both preferential ordering of the crystal domains and low surface roughness. Furthermore, we analyze the temperature-dependent behavior of our resonators to learn about how the quasi-particle density in the Nb film is affected by the niobium crystal structure and the presence of grain boundaries. Then, we explore yet a different material platform by attempting to realize onchip NbTiN single photon detectors on LiNbO₃, an emerging photonic platform with high potential for scalable quantum information processing. We use DC reactive magnetron sputtering to grow high-quality NbTiN thin films and investigate the impact of substrate temperature during NbTiN growth. We achieve four nm thick superconducting films with a critical temperature (𝑇𝑐) of 12.3 K grown at a substrate temperature of 825 K. We demonstrate that the increased substrate temperature reduces the oxygen concentration in our films and improves the overall stoichiometry. In addition, we integrate these films with the LiNbO3 platform and investigate the obtained interface quality. Finally, we fabricate superconducting nanowire single photon detectors from the NbTiN film on LiNbO₃ and characterize the detector performance. Lastly, we report a gate-tunable Josephson diode effect in hybrid nanowire junctions consisting of a spin-orbit-coupled semiconductor core coated with epitaxial ferromagnetic insulator and superconductor shells. The wires display a hysteretic superconducting window as a function of axial magnetic field. In the superconducting regime, the devices exhibit nonreciprocal current transport, with the diode efficiency showing a strong dependence on back-gate voltage. The effect persists in a remanent magnetization state following a controlled demagnetization procedure, establishing zero-field operation. The combination of results presented in this thesis stress the importance of a material-focused approach in advancing the performance of quantum hardware. The novel hybrid material platforms developed in this thesis expand the operating regime of devices, which could enable future experiments involving gate-tunable superconductivity or topological properties. Similarly, we demonstrate that optimizing superconductor crystal structure benefits quantum devices, such as single-photon detectors and superconducting resonators.
The frst part of the thesis describes the instrumentation, testing and analysis of a planar circuit designed for the measurement of the current-phase relationship of niobium-cobalt-insulator-niobium Josephson junctions. A detailed analysis method and fitting routine was developed but the results show that an irreducible mutual inductance places a limit on the accuracy of the chip for the intended measurement. The second part describes a study of the magnetic and microwave properties of a range of thin film niobium coplanar resonators with cobalt and normal metal layers. Magnetic measurements show a magnetic dead layer of 1.3 nm. The observed microwave losses are found to be two orders of magnitude higher than for high quality niobium films. Computer simulation shows that this is mainly due to conductive, rather than magnetic losses, and is in good agreement with the observed proportionality to cobalt thickness. Measurements of the temperature and magnetic field dependence of the losses and resonant frequency as a function of the cobalt thickness show no signs of the oscillatory thickness dependence reported in a number of other experiments. The temperature dependence of all films is found to be in good agreement with Mattis-Bardeen theory.