Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEICE Transactions on Electronics

Evaluation of Low-Power Single-Flux-Quantum Circuits Fabricated with a 250 A/cm2 Nb/AlOx/Nb Josephson Junction Process Using a Dilution Refrigerator

Masamitsu Tanaka, Tomoki UEDA, Yoshihiro KITAGAWA, T. Satoh, Tsuyoshi YAMAMOTO

Published Apr 22, 2026• 0 citations
Publisher

Abstract

We report the measurement results of the low-power single-flux-quantum (SFQ) circuits below 20 mK using a dilution refrigerator. We have been developing the SFQ circuits using a lowered critical current density process (250 A/cm2) and low-voltage design (0.1–0.5 mV) toward digital signal processing near superconductor quantum bits. So far, we have designed several basic SFQ cells, including wiring elements, flip-flops, and logic gates, using the four Nb planarized layer process and obtained the correct operation at 300 mK. In this study, we tested several SFQ circuits aiming to evaluate the operation at the mixing chamber stage of a dilution refrigerator. Our experimental results show that there was almost no change of device parameters, such as critical current values of Josephson junctions, or operating margins of the basic cells between 300 mK and 16 mK.

DOI
10.1587/transele.2025sep0002

Related papers

Design and Fabrication of Low-Power Single-Flux-Quantum Circuits Toward Quantum Bit Control

Masamitsu Tanaka, Yoshihiro Kitagawa, T. Satoh +1 more

We report low-power single-flux-quantum (SFQ) circuits fabricated with a lowered critical current density process and low-voltage design. We selected 250 A/cm$^{2}$to obtain 2–10 μA Josephson junctions (JJs) easily using conventional facilities. Our numerical simulation shows that the expected operating frequency is 10 GHz and that we can reduce the bias voltage to 0.1–0.5 mV; power consumption can be reduced to around 1 nW per JJ. We newly developed a fabrication process featuring four planarized Nb layers and a Pd resistor layer. We obtained the correct operation of several basic SFQ circuit elements designed with the lowered critical currents to 1/2 of the conventional circuits at 4.2 K. We also evaluated the Josephson junction critical currents, specific capacitance, resistance, and inductance at 3 K and 300 mK. We observed an increase of 7% in the critical currents at 300 mK, while the other parameters were unchanged. We demonstrated a 0.5-mV Josephson transmission line where we lowered the critical currents to 1/10. We expect such low-power SFQ circuits to operate at 20 mK, providing classical, general-purpose digital processing near quantum bits.

IEEE Transactions on Applied Superconductivity•Mar 2, 2023•15 citations

High-Frequency Operation of Low-Power Single-Flux-Quantum Circuits Fabricated Using 250 A/cm2 Nb/AlOx/Nb Planarization Process

Masamitsu Tanaka, Yoshihiro Kitagawa, T. Satoh +1 more

Superconductor single-flux-quantum (SFQ) integrated circuits can provide classical, general-purpose digital processing at cryogenic temperature near quantum bits. We report high-frequency operation of low-power SFQ circuits using a lowered critical current density fabrication process and low-voltage design. We are developing a standard-cell library with integrated devices featuring four planarized Nb layers and a Pd resistor layer. SFQ shift registers successfully operated at up to 11 GHz at 0.3 K. The measured operating frequency is sufficient for SFQ-based digital controlling of quantum bits using impulse-shaped voltage pulses.

IEEE International Conference on IC Design and Technology (ICICDT)•Sep 25, 2023•1 citation

Low-Power Single-Flux-Quantum Standard Cell Library Using 250 A/cm$^{2}$ Process for Qubit Control Applications

Masamitsu Tanaka, Yoshihiro Kitagawa, T. Satoh +1 more

In this paper, we report the development of a low-power single-flux-quantum (SFQ) standard cell library and experimental results, including the cell design, high-speed test of shift-registers, delay measurement using ring oscillators, and demonstration of simple demultiplexers. We fabricated the SFQ circuits using a lowered critical current density (250 A/cm$^{2}$) process and low-voltage design (0.5 or 0.1 mV). We reduced the power consumption to 1/50 or 1/250 from the conventional SFQ circuits operating at 4.2 K. We designed several essential SFQ cells, including wiring elements, flip-flops, and logic gates with the fabrication process using four planarized Nb layers and obtained the correct operation at 0.3 K. We tested 8-bit shift-registers aiming to evaluate the operating frequency of the developed SFQ cells. The 0.1-mV shift-registers operated up to 8.5 GHz. The experimental results of ring oscillators showed good agreement with the analog circuit simulation results. We believe that our experimentally-verified standard cell library is ready to use for SFQ-based digital control of qubits, such as demultiplexing of control signals, and the timing information and power consumption will be valuable information as the baseline to discuss future scalable quantum computer systems.

IEEE Transactions on Applied Superconductivity•Dec 24, 2024•4 citations

Design and Verification of SFQ Cell Library for Superconducting LSI Digital Circuits

Xiaoping Gao, Qi Qiao, Mingliang Wang +5 more

We have developed a cell library for superconducting large scale integrated (LSI) digital circuits based on Single Flux Quantum (SFQ) devices. The circuits were designed for a 6-kA/cm2Nb/AlOx/Nb junction process with 10 mask levels including one ground plane and two Nb wiring layers. The initial design and optimization of the circuit parameters were achieved by means of the optimization functions in a circuit simulator, PSCAN2, to ensure that important circuit parameters, Josephson critical current (IC), bias current (Ibias), and inductance satisfied minimal margin requirements. Critical margins of ICand Ibiaswere then further improved manually. To compensate the scattering in the circuit parameters from fabrication by design as much as possible, the critical junction parameters were optimized to further centralize the IC. The library cells were laid out following our design rules determined by systematic experiments on process control monitors (PCM). Basic cells including Josephson transmission lines, splitters, confluence buffers, D flip-flops, T flip-flops, and XOR and NDRO gates were designed, fabricated, and successfully tested at low frequencies. Wide overlaps of the operating regions for the common bias voltages were confirmed.

IEEE Transactions on Applied Superconductivity•Mar 11, 2021•34 citations

Rapid single-flux-quantum and adiabatic quantum-flux-parametron cell libraries using a 1 kA/cm2 niobium fabrication process

Taiki Yamae, Yuki Hironaka, Shuichi Nagasawa +3 more

Abstract Superconductor logic families can operate with small power dissipation and are thus suitable as building blocks for various computing systems. In some applications, superconductor logic circuits should be designed using Josephson junctions with low I c values ( I c : critical current). For instance, lowering I c values enables qubit interface circuits to operate with very small power dissipation at ~10 mK and stochastic electronics to easily induce stochastic operations. In this study, we develop the AIST 1 kA cm −2 Nb planarized process (1KP) with a minimum critical current of 10 µA, dedicated to the design of qubit interface circuits and stochastic electronics. We also develop rapid single-flux-quantum (RSFQ) and adiabatic quantum-flux-parametron (AQFP) cell libraries using the 1KP. The power dissipation of RSFQ logic using the 1KP can be reduced to 3.2% of that for conventional RSFQ logic by reducing both I c values and a bias voltage. Furthermore, the amount of supply currents for AQFP circuits using the 1KP can be reduced to ~40% of that for conventional AQFP circuits due to a large mutual inductance between AQFP gates and excitation lines, which results from a reduction in I c and an increase in inductances. We demonstrate RSFQ and AQFP circuits fabricated by the 1KP at 4.2 K. These results indicate that RSFQ and AQFP circuits using the 1KP have the potential to be used for the design of qubit interface circuits and stochastic electronics.

Scientific Reports•Nov 21, 2025•4 citations

Single Flux Quantum Circuit Operation at Millikelvin Temperatures

Jason Walter, Adam C. Weis, Kan-Ting Tsai +6 more

As quantum computing processors increase in size, there is growing interest in developing cryogenic electronics to overcome significant challenges to system scaling. Single flux-quantum (SFQ) circuits offer a promising alternative to remote, bulky, and power-hungry room temperature electronics. To meet the need for digital qubit control, readout, and co-processing, SFQ circuits must be adapted to operate at millikelvin temperatures near quantum processors. SEEQC's SFQuClass digital quantum management approach proximally places energy-efficient SFQ (ERSFQ) circuits and qubits in a multi-chip module. This enables extremely low power dissipation, compatible with a typical dilution cryostat's limited cooling power, while maintaining high processing speed and low error rates. We report on systematic testing from 4 K to 10 mK of a comprehensive set of ERSFQ cells, as well as more complex circuits such as programmable counters and demultiplexers used in digital qubit control. We compare the operating margins and error rates of these circuits and find that, at millikelvin, bias margins decrease and the center of the margins (i.e., the optimal bias current value) increases by ~15%, compared to 4.2 K. The margins can be restored by thermal annealing by reducing Josephson junction (JJ) critical current Ic. To provide guidance for how circuit parameters vary from 4.2 K to millikelvin, relevant analog process control monitors (PCMs) were tested in the temperature range of interest. The measured JJ critical current (of the PCM JJ arrays) increases by ~15% when decreasing temperature from 4.2 K to millikelvin, in good agreement with both theory and the empirically measured change in the center of bias margins for the tested digital circuits.

quant-pharXiv:2512.06895•IEEE Transactions on Applied Superconductivity•Dec 9, 2025•3 citations
We report the measurement results of the low-power single-flux-quantum (SFQ) circuits below 20 mK using a dilution refrigerator. We have been developing the SFQ circuits using a lowered critical current density process (250 A/cm2) and low-voltage design (0.1–0.5 mV) toward digital signal processing near superconductor quantum bits. So far, we have designed several basic SFQ cells, including wiring elements, flip-flops, and logic gates, using the four Nb planarized layer process and obtained the correct operation at 300 mK. In this study, we tested several SFQ circuits aiming to evaluate the operation at the mixing chamber stage of a dilution refrigerator. Our experimental results show that there was almost no change of device parameters, such as critical current values of Josephson junctions, or operating margins of the basic cells between 300 mK and 16 mK.
We report low-power single-flux-quantum (SFQ) circuits fabricated with a lowered critical current density process and low-voltage design. We selected 250 A/cm2^{2}2to obtain 2–10 μA Josephson junctions (JJs) easily using conventional facilities. Our numerical simulation shows that the expected operating frequency is 10 GHz and that we can reduce the bias voltage to 0.1–0.5 mV; power consumption can be reduced to around 1 nW per JJ. We newly developed a fabrication process featuring four planarized Nb layers and a Pd resistor layer. We obtained the correct operation of several basic SFQ circuit elements designed with the lowered critical currents to 1/2 of the conventional circuits at 4.2 K. We also evaluated the Josephson junction critical currents, specific capacitance, resistance, and inductance at 3 K and 300 mK. We observed an increase of 7% in the critical currents at 300 mK, while the other parameters were unchanged. We demonstrated a 0.5-mV Josephson transmission line where we lowered the critical currents to 1/10. We expect such low-power SFQ circuits to operate at 20 mK, providing classical, general-purpose digital processing near quantum bits.
Superconductor single-flux-quantum (SFQ) integrated circuits can provide classical, general-purpose digital processing at cryogenic temperature near quantum bits. We report high-frequency operation of low-power SFQ circuits using a lowered critical current density fabrication process and low-voltage design. We are developing a standard-cell library with integrated devices featuring four planarized Nb layers and a Pd resistor layer. SFQ shift registers successfully operated at up to 11 GHz at 0.3 K. The measured operating frequency is sufficient for SFQ-based digital controlling of quantum bits using impulse-shaped voltage pulses.
Low-Power Single-Flux-Quantum Standard Cell Library Using 250 A/cm2^{2}2 Process for Qubit Control Applications
In this paper, we report the development of a low-power single-flux-quantum (SFQ) standard cell library and experimental results, including the cell design, high-speed test of shift-registers, delay measurement using ring oscillators, and demonstration of simple demultiplexers. We fabricated the SFQ circuits using a lowered critical current density (250 A/cm2^{2}2) process and low-voltage design (0.5 or 0.1 mV). We reduced the power consumption to 1/50 or 1/250 from the conventional SFQ circuits operating at 4.2 K. We designed several essential SFQ cells, including wiring elements, flip-flops, and logic gates with the fabrication process using four planarized Nb layers and obtained the correct operation at 0.3 K. We tested 8-bit shift-registers aiming to evaluate the operating frequency of the developed SFQ cells. The 0.1-mV shift-registers operated up to 8.5 GHz. The experimental results of ring oscillators showed good agreement with the analog circuit simulation results. We believe that our experimentally-verified standard cell library is ready to use for SFQ-based digital control of qubits, such as demultiplexing of control signals, and the timing information and power consumption will be valuable information as the baseline to discuss future scalable quantum computer systems.
We have developed a cell library for superconducting large scale integrated (LSI) digital circuits based on Single Flux Quantum (SFQ) devices. The circuits were designed for a 6-kA/cm2Nb/AlOx/Nb junction process with 10 mask levels including one ground plane and two Nb wiring layers. The initial design and optimization of the circuit parameters were achieved by means of the optimization functions in a circuit simulator, PSCAN2, to ensure that important circuit parameters, Josephson critical current (IC), bias current (Ibias), and inductance satisfied minimal margin requirements. Critical margins of ICand Ibiaswere then further improved manually. To compensate the scattering in the circuit parameters from fabrication by design as much as possible, the critical junction parameters were optimized to further centralize the IC. The library cells were laid out following our design rules determined by systematic experiments on process control monitors (PCM). Basic cells including Josephson transmission lines, splitters, confluence buffers, D flip-flops, T flip-flops, and XOR and NDRO gates were designed, fabricated, and successfully tested at low frequencies. Wide overlaps of the operating regions for the common bias voltages were confirmed.
Abstract Superconductor logic families can operate with small power dissipation and are thus suitable as building blocks for various computing systems. In some applications, superconductor logic circuits should be designed using Josephson junctions with low I c values ( I c : critical current). For instance, lowering I c values enables qubit interface circuits to operate with very small power dissipation at ~10 mK and stochastic electronics to easily induce stochastic operations. In this study, we develop the AIST 1 kA cm −2 Nb planarized process (1KP) with a minimum critical current of 10 µA, dedicated to the design of qubit interface circuits and stochastic electronics. We also develop rapid single-flux-quantum (RSFQ) and adiabatic quantum-flux-parametron (AQFP) cell libraries using the 1KP. The power dissipation of RSFQ logic using the 1KP can be reduced to 3.2% of that for conventional RSFQ logic by reducing both I c values and a bias voltage. Furthermore, the amount of supply currents for AQFP circuits using the 1KP can be reduced to ~40% of that for conventional AQFP circuits due to a large mutual inductance between AQFP gates and excitation lines, which results from a reduction in I c and an increase in inductances. We demonstrate RSFQ and AQFP circuits fabricated by the 1KP at 4.2 K. These results indicate that RSFQ and AQFP circuits using the 1KP have the potential to be used for the design of qubit interface circuits and stochastic electronics.
As quantum computing processors increase in size, there is growing interest in developing cryogenic electronics to overcome significant challenges to system scaling. Single flux-quantum (SFQ) circuits offer a promising alternative to remote, bulky, and power-hungry room temperature electronics. To meet the need for digital qubit control, readout, and co-processing, SFQ circuits must be adapted to operate at millikelvin temperatures near quantum processors. SEEQC's SFQuClass digital quantum management approach proximally places energy-efficient SFQ (ERSFQ) circuits and qubits in a multi-chip module. This enables extremely low power dissipation, compatible with a typical dilution cryostat's limited cooling power, while maintaining high processing speed and low error rates. We report on systematic testing from 4 K to 10 mK of a comprehensive set of ERSFQ cells, as well as more complex circuits such as programmable counters and demultiplexers used in digital qubit control. We compare the operating margins and error rates of these circuits and find that, at millikelvin, bias margins decrease and the center of the margins (i.e., the optimal bias current value) increases by ~15%, compared to 4.2 K. The margins can be restored by thermal annealing by reducing Josephson junction (JJ) critical current Ic. To provide guidance for how circuit parameters vary from 4.2 K to millikelvin, relevant analog process control monitors (PCMs) were tested in the temperature range of interest. The measured JJ critical current (of the PCM JJ arrays) increases by ~15% when decreasing temperature from 4.2 K to millikelvin, in good agreement with both theory and the empirically measured change in the center of bias margins for the tested digital circuits.