We describe the fabrication and measurement of microwave coplanar waveguide resonators with internal quality factors above 107 at high microwave powers and over 106 at low powers, with the best low power results approaching 2×106, corresponding to ∼1 photon in the resonator. These quality factors are achieved by controllably producing very smooth and clean interfaces between the resonators’ aluminum metallization and the underlying single crystal sapphire substrate. Additionally, we describe a method for analyzing the resonator microwave response, with which we can directly determine the internal quality factor and frequency of a resonator embedded in an imperfect measurement circuit.
We successfully designed and fabricated an absorption-type of superconducting coplanar waveguide (CPW) resonators. The resonators are made from a niobium film (about 160 nm thick) on a high-resistance Si substrate, and each resonator is fabricated as a meandered quarter-wavelength transmission line (one end is short to the ground and another end is capacitively coupled to a through feedline). With a vector network analyzer we measured the transmissions of the applied microwave through the resonators at ultra-low temperature. The obtained loaded quality factors are significantly high, i.e. up to ∼10 6 . When the temperature increases slowly from the base temperature (20 mK), the resonance frequencies of the resonators are blue shifted and the quality factors are lowered slightly. In principle, this type of device can integrate a series of CPW resonators with a common feedline, making it a promising candidate as the data bus for coupling distant solid-state qubits and the sensitive detector of single photons.
Abstract Tantalum (Ta) has recently received considerable attention in manufacturing robust superconducting quantum circuits. Ta offers low microwave loss, high kinetic inductance compared to aluminium (Al) and niobium (Nb), and good compatibility with complementary metal-oxide-semiconductor (CMOS) technology, which is essential for quantum computing applications. Here we demonstrate the fabrication engineering of thickness-dependent high-quality-factor (high-
Qi ) Ta superconducting microwave coplanar waveguide resonators. All films are deposited on high-resistivity silicon substrates at room temperature without additional substrate heating. Before Ta deposition, a niobium (Nb) seed layer is used to promote a body-centred cubic lattice (
α -Ta) formation. We further engineer the kinetic inductance (
LK ) of the resonators by varying Ta film thicknesses. High
LK is a key advantage for applications because it facilitates the realisation of high-impedance, compact quantum circuits with enhanced coupling to qubits. The maximum internal quality factor
Qi of
∼ 3.6 × 10 6 in the high power regime and
Qi of
∼ 4.5 × 10 5 in the single-photon regime is achieved for 100 nm Ta which represents an improvement over previous room-temperature deposited Ta resonators on silicon substrates in the single photon regime, while the highest kinetic inductance of 0.6 pH/sq is obtained for the thinnest film, which is 40 nm. This combination of high
Qi and high
LK highlights the potential of Ta microwave circuits for high-fidelity operation of compact quantum circuits.
The high critical magnetic field and relatively high critical temperature of niobium nitride (NbN) make it a promising material for applications in superconducting quantum technology. However, NbN-based superconducting circuits are sensitive to decoherence sources such as two-level system (TLS) defects. Here, we numerically and experimentally investigate NbN superconducting microwave coplanar waveguide resonator arrays with a 100 nm thickness, capacitively coupled to a common coplanar waveguide on a silicon chip. We observe that the resonators' internal quality factor (
Qi) decreases from
Qi∼1.07×106in a high power regime to
Qi∼1.36×105in the single photon regime. Data from this study is consistent with the TLS theory, which describes the TLS interactions in resonator substrates and interfaces. Moreover, we study the temperature (
T) dependence of
Qiand resonance frequency
frof coplanar waveguide resonators to characterize the quasiparticle density. We observe that the increase in kinetic inductance at higher temperatures is the main reason for the frequency shift. Finally, we measure
frand
Qiin response to in-plane magnetic fields (
B∣∣). We verify that
Qistays well above
104up to
B∣∣= 240 mT in the photon number
<nph>= 1.8 at
T= 100 mK. Our results could enable the development of robust microwave superconducting circuits for circuit quantum electrodynamics at high magnetic fields required for hybrid superconducting-semiconducting quantum circuits.
Superconducting coplanar waveguide (SCPW) resonators have a wide range of applications due to the combination of their planar geometry and high quality factors relative to normal metals. However, their performance is sensitive to both the details of their geometry and the materials and processes that are used in their fabrication. In this paper, we study the dependence of SCPW resonator performance on materials and geometry as a function of temperature and excitation power. We measure quality factors greater than 2 × 106 at high excitation power and 6 × 105 at a power comparable to that generated by a single microwave photon circulating in the resonator. We examine the limits to the high excitation power performance of the resonators and find it to be consistent with a model of radiation loss. We further observe that while in all cases the quality factors are degraded as the temperature and power are reduced due to dielectric loss, the size of this effect is dependent on resonator materials and geometry. Finally, we demonstrate that the dielectric loss can be controlled in principle using a separate excitation near the resonance frequencies of the resonator.
We present a specific method for fabrication of the original evaporation mask and characterisation of the superconduct- ing coplanar waveguide (CPW) resonators based on the shadow evaporation technique [1]. We show that silicon dioxide can be successfully removed by etching process in HF-based solutions. This treatment significantly increases the intrinsic quality factor Qi of the resonators and is also suitable for other superconducting structures operated at temperatures of the order of 20 mK. In this report we present a design of superconducting CPW resonators with a high quality factor to study fundamental problems of high kinetic inductance of aluminum ultra-thin films. Our kinetic inductance research was motivated by the necessity of ultra-short and high quality resonators which could be suitable for qubit systems. Also this kinetic inductance could be used in the development of parametric amplifiers [2] or new types of qubits based on quantum phase slip [3].