Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Time-Division SQUID Multiplexing With Nanohenry Scale Input Mutual Inductance Using Transformers With Intracoil Damping

Malcolm Durkin, D. A. Bennett, William Bertrand Doriese, Johnathon D. Gard, Johannes Hubmayr, Richard A. Lew, Erin Maloney, C. D. Reintsema, Christopher Rooney, Robinjeet Singh, Daniel R. Schmidt, Joel N. Ullom, Leila R. Vale, Michael R. Vissers

Published Apr 6, 2026• 0 citations
Publisher

Abstract

Time division multiplexing (TDM) developed for the Athena X-ray integral field unit (X-IFU) has achieved readout performance that can be scaled to multiplexing factors of several hundred for TES bolometer missions. The lower slew rate requirements of bolometer and soft X-ray missions favor greater first stage SQUID amplifier input mutual inductance (Min) to reduce readout noise and compensate for aliasing as multiplexing factor is increased. We find that, asMinincreases, TDM performance becomes sensitive to the design of the TES bias circuit, with degraded noise performance and the emergence of resonant features. In TDM chips with nanohenry scaleMin, we demonstrate that this sensitivity can be eliminated by adding intra-coil damping resistors to the superconducting transformers, enabling the robust use of these higherMinmultiplexers.

DOI
10.1109/tasc.2026.3680761

Related papers

1/f Noise Reduction With Noise Modulation in Time-Division Multiplexing

Kazuhiro Sakai, John Adams, Conjeepuram V. Ambarish +13 more

We present a novel noise modulation technique using SQUID gain switching for Time Division Multiplexing (TDM) readout systems that reduces 1/f noise by a factor of 3.5 while preserving the architectural simplicity that makes TDM a widely used technique for Transition Edge Sensor (TES) arrays. In contrast to frequency division multiplexing or microwave multiplexing, where signal modulation inherently provides immunity to low-frequency noise, conventional TDM systems can be susceptible to 1/f noise from downstream electronics as the TES signals remain in the low-frequency band. In our approach, the operating point of the SQUID amplifier alternates between positive and negative gain slopes at the frame frequency, combined with synchronized digital inversion of the error signals prior to flux-locked loop integration. This modulation scheme shifts the readout noise, including the 1/f components of low noise amplifiers, analog-to-digital converters and room temperature electronics, into the frame frequency range where it can be separated from the DC-TES signal by decimation filtering. Laboratory validation using an 8 column × 32 row TDM platform designed for Athena X-IFU applications shows a reduction in 1/f noise from 73 pA/√Hz@1Hz (9.3 μΦ₀/√Hz) to 21 pA/√Hz@1Hz (2.7 μΦ₀/√Hz) in channels with no TES connected, with the additional benefits of a 14-fold reduction in SQUID bias sensitivity through dynamic resistance matching and a 6.5-fold reduction in temperature-induced baseline drift. The technique avoids the disadvantage of doubling white noise, which occurs with conventional noise subtraction methods, and at the same time achieves a comparable suppression of 1/f noise. Implementation requires only minor firmware modifications to existing TDM systems, making it easily implementable for far-infrared bolometric and X-ray spectroscopy applications.

IEEE Transactions on Applied Superconductivity•Jan 12, 2026•1 citation

Nearly Quantum Limited Two-Stage SQUID Amplifiers for the Frequency Domain Multiplexing of TES Based X-ray and Infrared Detectors

Luciano G. Gottardi, M. Kiviranta, Jan van der Kuur +3 more

The frequency domain multiplexing (FDM) readout of arrays of transition edges sensors for the X-IFU/Athena and SAFARI/SPICA instruments requires SQUID amplifiers with low input inductance, low flux noise, high-dynamic range and low power consumption. We report the performance of two-stage SQUID amplifiers developed at VTT coupled to multiple high-Q LC resonators of the SRON FDM readout operating in the frequency range from 2 to 5 MHz. The SQUIDs have been tested in the following configurations: 1) the two SQUIDs at base temperature with open input; 2) the amplifier SQUID at 1K temperature and the front-end SQUID at base temperature in the FDM readout of low-G TES bolometers; and 3) and in the FDM readout of X-ray microcalorimeter arrays with both SQUIDS at base temperature. We measured an input flux noise equal to 0.18 μΦ0/Hz1/2at 20 mK, equivalent to an energy resolution of 9 b. The measured current noise at the SQUID input is ~1 pA/Hz1/2at 20 mK, which corresponds to a coupled energy resolution of about 15 b.

IEEE Transactions on Applied Superconductivity•Nov 10, 2014•15 citations

First Integration of Two-Level Time-Division Multiplexed Differential Readout With a Prototype CMB-S4 Detector Array

Brianna Cantrall, Shawn Henderson, Zeeshan Ahmed +11 more

Future cosmic microwave background (CMB) surveys will require an order of magnitude more detectors than are currently deployed in the most densely packed fielded experiments. This calls for a multiplexed readout capable of handling the increased integration complexity, heat load on the lowest temperature stages, and cost for such experiments. One choice of readout technology is direct current (DC) superconducting quantum interference device (SQUID)-based time-division multiplexing (TDM). This technology, along with transition-edge sensor (TES) detector technology, has been successfully deployed by multiple CMB experiments over the past decade. However, current experiments implementing TDM have not yet demonstrated the combination of multiplexing (MUX) factor, sampling rate, and noise performance at the scale of a next-generation experiment, such as CMB Stage 4 (CMB-S4). In order to meet these requirements, an advanced TDM architecture has been developed that features increased amplification of TES signals and increased bandwidth compared to previous MUX chip designs, as well as implementation of fully symmetric, differential circuits and hierarchical row addressing. We report on the first integration and noise characterization of this advanced TDM architecture with a prototype CMB-S4 dichroic detector wafer sensitive to the 90 and 150 GHz bands. Limitations of the legacy warm electronics used in this work preclude direct tests of the hierarchical MUX and fully differential signal paths; we instead focus on noise characterization at the SQUID and detector levels. Based on our measurements, the full system performance is projected to exceed CMB-S4 design requirements.

IEEE Transactions on Applied Superconductivity•Jul 29, 2026•1 citation

Dynamic behavior of dc SQUIDs in time-division multiplexing readout schemes

Erik Heinz, V. Zakosarenko, T. May +1 more

We have investigated the transient response of superconducting quantum interference devices (SQUIDs) used in time-division multiplexing schemes for the readout from arrays of superconducting transition-edge sensors (TES). In time-division multiplexing the per channel settling time is an important parameter since it limits the multiplexing frequency as well as the signal-to-noise ratio. Although SQUIDs in general are fast cryoelectronic devices operating at a nanosecond scale, experimental evidence shows that the settling time in bias-switched SQUID multiplexers can, in the case of a low impedance input circuit, reach several microseconds. We have confirmed this behavior through numerical transient analysis using a Josephson circuit simulator. Within the simulation we have found that the transient response can be reduced using an extra inductor in series with the input coil of the dc SQUID. This result in turn has been confirmed experimentally. We furthermore discuss the conflicting constraints that a desired high signal bandwidth places on the parameters of the multiplexer, the readout SQUIDs, and the TES.

Superconductor Science and Technology•Mar 7, 2013•9 citations

SiGe Integrated Circuit∕SQUID Hybrid Cryogenic Multiplexer for Superconducting Bolometer Array

D. Prêle, Fabrice Voisin, R. Oger +6 more

The development of large superconducting bolometer (Transition Edge Sensor: TES) arrays requires ultra low noise amplification and multiplexing electronics. The use of a first transducer stage such as a SQUID (Superconducting QUantum Interference Device) allows ultimate performance in terms of noise. However, the linearization of the SQUID characteristic requires low noise amplification. Furthermore, to realize a time domain multiplexer with SQUIDs, switched biasing is also needed. We have designed an Integrated Circuit (IC) in standard BiCMOS SiGe technology for the readout and the control of a SQUID multiplexer. It includes a low noise amplifier with multiplexed inputs, switched current sources for SQUIDs, and digital circuit for the addressing with only one room temperature clock signal. We have successfully tested this integrated circuit down to 2 K. To validate the operation of a SQUID multiplexer controlled by this SiGe cryogenic IC, we have developed a 2×2 SQUID hybrid demonstrator. It consists of four commercial SQUIDs connected to a SiGe IC.

AIP conference proceedings•Jan 1, 2009•3 citations

Development of frequency domain multiplexing readout using sub-kelvin SQUIDs for LiteBIRD

Megan Russell, Kam Arnold, T. Elleflot +6 more

LiteBIRD is a satellite mission designed to map the polarization of the Cosmic Microwave Background (CMB) at degree and larger scales from 40 to 402 GHz. LiteBIRD will use 4,600 Transition-Edge Sensor (TES) bolometers biased and read out using Digital Frequency Domain Multiplexing (DfMux). The DfMux implementation for LiteBIRD uses sub-kelvin Superconducting Quantum Interference Device (SQUID) at the same 0.1 K thermal stage as the detectors, this allows for reduced parasitic impedances within the mK circuit and improved SQUID performance. Additionally it must work in the integrated system with the spacecraft’s wiring harnesses, which will be longer than is typical on similar ground based experiments, and therefore have more significant parasitic impedances which will impact readout performance. The properties of SQUID candidates at millikelvin temperatures and effects of the spacecraft-like meter scale wiring harness are investigated. Additionally, the possibility of inductively rather than resistively biasing our bolometers at the 0.1K stage, to reduce power dissipation in the bias element, is investigated. We will report progress on validating the cryogenic components of this readout system.

Millimeter, Submillimeter, and Far-Infrared Detectors and Instrumentation for Astronomy XI•Jul 16, 2022•5 citations
Time division multiplexing (TDM) developed for the Athena X-ray integral field unit (X-IFU) has achieved readout performance that can be scaled to multiplexing factors of several hundred for TES bolometer missions. The lower slew rate requirements of bolometer and soft X-ray missions favor greater first stage SQUID amplifier input mutual inductance (Min) to reduce readout noise and compensate for aliasing as multiplexing factor is increased. We find that, asMinincreases, TDM performance becomes sensitive to the design of the TES bias circuit, with degraded noise performance and the emergence of resonant features. In TDM chips with nanohenry scaleMin, we demonstrate that this sensitivity can be eliminated by adding intra-coil damping resistors to the superconducting transformers, enabling the robust use of these higherMinmultiplexers.
We present a novel noise modulation technique using SQUID gain switching for Time Division Multiplexing (TDM) readout systems that reduces 1/f noise by a factor of 3.5 while preserving the architectural simplicity that makes TDM a widely used technique for Transition Edge Sensor (TES) arrays. In contrast to frequency division multiplexing or microwave multiplexing, where signal modulation inherently provides immunity to low-frequency noise, conventional TDM systems can be susceptible to 1/f noise from downstream electronics as the TES signals remain in the low-frequency band. In our approach, the operating point of the SQUID amplifier alternates between positive and negative gain slopes at the frame frequency, combined with synchronized digital inversion of the error signals prior to flux-locked loop integration. This modulation scheme shifts the readout noise, including the 1/f components of low noise amplifiers, analog-to-digital converters and room temperature electronics, into the frame frequency range where it can be separated from the DC-TES signal by decimation filtering. Laboratory validation using an 8 column × 32 row TDM platform designed for Athena X-IFU applications shows a reduction in 1/f noise from 73 pA/√Hz@1Hz (9.3 μΦ₀/√Hz) to 21 pA/√Hz@1Hz (2.7 μΦ₀/√Hz) in channels with no TES connected, with the additional benefits of a 14-fold reduction in SQUID bias sensitivity through dynamic resistance matching and a 6.5-fold reduction in temperature-induced baseline drift. The technique avoids the disadvantage of doubling white noise, which occurs with conventional noise subtraction methods, and at the same time achieves a comparable suppression of 1/f noise. Implementation requires only minor firmware modifications to existing TDM systems, making it easily implementable for far-infrared bolometric and X-ray spectroscopy applications.
The frequency domain multiplexing (FDM) readout of arrays of transition edges sensors for the X-IFU/Athena and SAFARI/SPICA instruments requires SQUID amplifiers with low input inductance, low flux noise, high-dynamic range and low power consumption. We report the performance of two-stage SQUID amplifiers developed at VTT coupled to multiple high-Q LC resonators of the SRON FDM readout operating in the frequency range from 2 to 5 MHz. The SQUIDs have been tested in the following configurations: 1) the two SQUIDs at base temperature with open input; 2) the amplifier SQUID at 1K temperature and the front-end SQUID at base temperature in the FDM readout of low-G TES bolometers; and 3) and in the FDM readout of X-ray microcalorimeter arrays with both SQUIDS at base temperature. We measured an input flux noise equal to 0.18 μΦ0/Hz1/2at 20 mK, equivalent to an energy resolution of 9 b. The measured current noise at the SQUID input is ~1 pA/Hz1/2at 20 mK, which corresponds to a coupled energy resolution of about 15 b.
Future cosmic microwave background (CMB) surveys will require an order of magnitude more detectors than are currently deployed in the most densely packed fielded experiments. This calls for a multiplexed readout capable of handling the increased integration complexity, heat load on the lowest temperature stages, and cost for such experiments. One choice of readout technology is direct current (DC) superconducting quantum interference device (SQUID)-based time-division multiplexing (TDM). This technology, along with transition-edge sensor (TES) detector technology, has been successfully deployed by multiple CMB experiments over the past decade. However, current experiments implementing TDM have not yet demonstrated the combination of multiplexing (MUX) factor, sampling rate, and noise performance at the scale of a next-generation experiment, such as CMB Stage 4 (CMB-S4). In order to meet these requirements, an advanced TDM architecture has been developed that features increased amplification of TES signals and increased bandwidth compared to previous MUX chip designs, as well as implementation of fully symmetric, differential circuits and hierarchical row addressing. We report on the first integration and noise characterization of this advanced TDM architecture with a prototype CMB-S4 dichroic detector wafer sensitive to the 90 and 150 GHz bands. Limitations of the legacy warm electronics used in this work preclude direct tests of the hierarchical MUX and fully differential signal paths; we instead focus on noise characterization at the SQUID and detector levels. Based on our measurements, the full system performance is projected to exceed CMB-S4 design requirements.
We have investigated the transient response of superconducting quantum interference devices (SQUIDs) used in time-division multiplexing schemes for the readout from arrays of superconducting transition-edge sensors (TES). In time-division multiplexing the per channel settling time is an important parameter since it limits the multiplexing frequency as well as the signal-to-noise ratio. Although SQUIDs in general are fast cryoelectronic devices operating at a nanosecond scale, experimental evidence shows that the settling time in bias-switched SQUID multiplexers can, in the case of a low impedance input circuit, reach several microseconds. We have confirmed this behavior through numerical transient analysis using a Josephson circuit simulator. Within the simulation we have found that the transient response can be reduced using an extra inductor in series with the input coil of the dc SQUID. This result in turn has been confirmed experimentally. We furthermore discuss the conflicting constraints that a desired high signal bandwidth places on the parameters of the multiplexer, the readout SQUIDs, and the TES.
The development of large superconducting bolometer (Transition Edge Sensor: TES) arrays requires ultra low noise amplification and multiplexing electronics. The use of a first transducer stage such as a SQUID (Superconducting QUantum Interference Device) allows ultimate performance in terms of noise. However, the linearization of the SQUID characteristic requires low noise amplification. Furthermore, to realize a time domain multiplexer with SQUIDs, switched biasing is also needed. We have designed an Integrated Circuit (IC) in standard BiCMOS SiGe technology for the readout and the control of a SQUID multiplexer. It includes a low noise amplifier with multiplexed inputs, switched current sources for SQUIDs, and digital circuit for the addressing with only one room temperature clock signal. We have successfully tested this integrated circuit down to 2 K. To validate the operation of a SQUID multiplexer controlled by this SiGe cryogenic IC, we have developed a 2×2 SQUID hybrid demonstrator. It consists of four commercial SQUIDs connected to a SiGe IC.
LiteBIRD is a satellite mission designed to map the polarization of the Cosmic Microwave Background (CMB) at degree and larger scales from 40 to 402 GHz. LiteBIRD will use 4,600 Transition-Edge Sensor (TES) bolometers biased and read out using Digital Frequency Domain Multiplexing (DfMux). The DfMux implementation for LiteBIRD uses sub-kelvin Superconducting Quantum Interference Device (SQUID) at the same 0.1 K thermal stage as the detectors, this allows for reduced parasitic impedances within the mK circuit and improved SQUID performance. Additionally it must work in the integrated system with the spacecraft’s wiring harnesses, which will be longer than is typical on similar ground based experiments, and therefore have more significant parasitic impedances which will impact readout performance. The properties of SQUID candidates at millikelvin temperatures and effects of the spacecraft-like meter scale wiring harness are investigated. Additionally, the possibility of inductively rather than resistively biasing our bolometers at the 0.1K stage, to reduce power dissipation in the bias element, is investigated. We will report progress on validating the cryogenic components of this readout system.