Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Study on the low-temperature superconducting characteristics of magnetron-sputtered hafnium thin film and coplanar waveguide resonator

LU Chunyan, CHAI Ye, LI Weiwei, LIU Zhouhui, CAO Duo, Zhang Yi, S. Shu, LIU Feng

Published Aug 1, 2025• 0 citations
Publisher

Abstract

Hafnium (Hf), as one of the few currently available elemental metals with low critical temperature (Tc ≤ 1 K) and high kinetic inductance (Ls ≥ 10 pH/□) among superconducting materials, retained potential for the development of detectors which were sensitive to near-infrared photons, and possessed high quality factor (Qi). In this paper, Hf thin film were prepared using magnetron sputtering. To characterize the low-temperature properties, a 1/4 wavelength coplanar waveguide resonator based on Hf thin films was fabricated. Detailed experimental tests and studies were conducted on the surface characteristics of the thin films, as well as the correlation and dynamics among the resonator's resonant frequency, power, and temperature. Based on the test results, the Tc of the Hf thin films prepared was 356 mK, with Ls of 20.5 pH/□ and Qi reaching 2.6×103.

DOI
10.20192/j.cnki.jshnu(ns).2025.04.005

Related papers

Characterization of sputtered hafnium thin films for high quality factor microwave kinetic inductance detectors

Grégoire Coiffard, M. Daal, Nicholas Zobrist +4 more

Abstract Hafnium is an elemental superconductor which crystallizes in a hexagonal close packed structure, has a transition temperature T C ≃ 400 mK, and has a high normal state resistivity around 90 µ ω cm. In Microwave Kinetic Inductance Detectors (MKIDs), these properties are advantageous since they allow for creating detectors sensitive to optical and near infra-red radiation. In this work, we study how sputter conditions and especially the power applied to the target during the deposition, affect the hafnium T C , resistivity, stress, texture and preferred crystal orientation. We find that the position of the target with respect to the substrate strongly affects the orientation of the crystallites in the films and the internal quality factor, Q i , of MKIDs fabricated from the films. In particular, we demonstrate that a DC magnetron sputter deposition at a normal angle of incidence, low pressure, and low plasma power promotes the growth of compressive (002)-oriented films and that such films can be used to make high quality factor MKIDs with Q i up to 600,000.

arXiv:2004.00736•Superconductor Science and Technology•Apr 27, 2020•21 citations

Ultra high quality factor resonators for kinetic inductance detectors

G. Hammer, S. Wünsch, K. Ilin +1 more

The sensitivity of a kinetic inductance detector is determined by the performance of the cavity circuit and therefore a high quality factor and low phase noise are required. We developed superconducting niobium coplanar waveguide resonators for kinetic inductance detectors at a resonance frequency of 6 GHz. The length of the resonators is adjusted to a quarter of a wavelength which corresponds to ≈ 5.3 mm in our geometry. Different layouts with coplanar waveguide transmission line topology for the resonator were designed and simulated. Some parameters of the device fabrication process were varied. The niobium thin films were deposited by magnetron sputtering on sapphire substrates kept at ambient temperature. The resonators were patterned by photolithography and reactive ion etching and measured at helium temperatures. Because of the quarter wave geometry with one shorted end the reflection parameter was measured. We have studied the influence of the coupling capacitances on quality factor. The optimization includes microwave simulations and implementation in different resonator structures. The measurements of optimized devices showed a very high quality factor above one million (10 6 ). The obtained results and perspective on further development of resonators will be discussed.

Journal of Physics Conference Series•Feb 1, 2008•12 citations

Magnetic field resilient high kinetic inductance superconducting niobium nitride coplanar waveguide resonators

Cécile Xinqing Yu, Simon Zihlmann, Gonzalo Troncoso Fernández-Bada +4 more

We characterize niobium nitride (NbN) λ/2 coplanar waveguide resonators, which were fabricated from a 10-nm-thick film on silicon dioxide grown by sputter deposition. For films grown at 180 °C, we report a superconducting critical temperature of 7.4 K associated with a normal square resistance of 1 kΩ, leading to a kinetic inductance of 192 pH/◻. We fabricated resonators with a characteristic impedance up to 4.1 kΩ and internal quality factors Qi>104 in the single photon regime at zero magnetic field. Moreover, in the many photon regime, the resonators present a high magnetic field resilience with Qi>104 in a 6 T in-plane magnetic field and in a 300 mT out-of-plane magnetic field. These findings make such resonators a compelling choice for circuit quantum electrodynamics experiments involving quantum systems with small electric dipole moments operated in finite magnetic fields.

arXiv:2012.04366•Applied Physics Letters•Feb 1, 2021•66 citations

Tantalum Thin Films Sputtered on Silicon and on Different Seed Layers: Material Characterization and Coplanar Waveguide Resonator Performance

Moritz Singer, Benedikt Schoof, H. M. Gupta +3 more

Superconducting qubits are a promising platform for large-scale quantum computing. Besides the Josephson junction, most parts of a superconducting qubit are made of a planar, patterned superconducting thin films. In the past, most qubit architectures have relied on niobium (Nb) as the material of choice for the superconducting layer. However, there is also a variety of alternative materials with potentially less losses, which may thereby result in increased qubit performance. One such material is tantalum (Ta), for which high-performance qubit components have already been demonstrated. In this study, we report the sputter-deposition of Ta thin films directly on heated and unheated silicon (Si) substrates as well as onto different, nanometer-thin seed layers from tantalum nitride (TaN), titanium nitride (TiN) or aluminum nitride (AIN) that were deposited first. The thin films are characterized in terms of surface morphology, crystal structure, phase composition, critical temperature, residual resistance ratio (RRR) and RF-performance. We obtain thin films indicative of pure alpha-Ta for high temperature (600°C) sputtering directly on silicon and for Ta deposited on TaN or TiN seed layers. Coplanar waveguide (CPW) resonator measurements show that the Ta deposited directly on the heated silicon substrate performs best with internal quality factors Qi reaching 1xl06in the single-photon regime, measured at T=100 mK.

arXiv:2409.06041•IEEE International Conference on Quantum Computing and Engineering (QCE)•Sep 15, 2024•6 citations

Temperature and power characteristics of quarter-wavelength superconducting coplanar waveguide resonator

Huilong Yu, Lingxiao Jing, Tao Hua +1 more

Abstract A quarter wavelength superconducting aluminum film coplanar waveguide resonator with a high-quality factor was designed and fabricated. Furthermore, its resonant frequency and quality as a function of temperatures and exciting powers were investigated. The experimental results showed that the resonance frequency decreases about 1% with the increase of temperature from 50 mk to 1 K, and the load quality factor of the resonator also decreases. The resonant frequency decreases with power from − 120 to − 70 dBm. The quality factor increases with increased excitation power due to the loss decreases and nonlinearity. The results are consistent with the theoretical analysis of the surface impedance model.

SN Applied Sciences•Feb 2, 2022•3 citations

Fabrication and characterization of superconducting coplanar waveguide resonators

Bongkeon Kim, Minkyung Jung, Jihwan Kim +2 more

High-quality superconducting coplanar waveguide (SCPW) resonators are crucial for developing superconducting quantum information devices and sensors. We designed quarter-wavelength SCPW resonators and fabricated the SCPW resonators using Nb thin film. The resonant characteristics were measured at T = 4.2 K, revealing the intrinsic quality factor and the coupling quality factor to be Qi = 4,784 and Qc = 17, 980, respectively. Our design and fabrication techniques would be very useful to develop a gate-tunable superconducting qubit based on the semiconductor nanostructures.

•Dec 1, 2020•1 citation
Hafnium (Hf), as one of the few currently available elemental metals with low critical temperature (Tc ≤ 1 K) and high kinetic inductance (Ls ≥ 10 pH/□) among superconducting materials, retained potential for the development of detectors which were sensitive to near-infrared photons, and possessed high quality factor (Qi). In this paper, Hf thin film were prepared using magnetron sputtering. To characterize the low-temperature properties, a 1/4 wavelength coplanar waveguide resonator based on Hf thin films was fabricated. Detailed experimental tests and studies were conducted on the surface characteristics of the thin films, as well as the correlation and dynamics among the resonator's resonant frequency, power, and temperature. Based on the test results, the Tc of the Hf thin films prepared was 356 mK, with Ls of 20.5 pH/□ and Qi reaching 2.6×103.
Abstract Hafnium is an elemental superconductor which crystallizes in a hexagonal close packed structure, has a transition temperature T C ≃ 400 mK, and has a high normal state resistivity around 90 µ ω cm. In Microwave Kinetic Inductance Detectors (MKIDs), these properties are advantageous since they allow for creating detectors sensitive to optical and near infra-red radiation. In this work, we study how sputter conditions and especially the power applied to the target during the deposition, affect the hafnium T C , resistivity, stress, texture and preferred crystal orientation. We find that the position of the target with respect to the substrate strongly affects the orientation of the crystallites in the films and the internal quality factor, Q i , of MKIDs fabricated from the films. In particular, we demonstrate that a DC magnetron sputter deposition at a normal angle of incidence, low pressure, and low plasma power promotes the growth of compressive (002)-oriented films and that such films can be used to make high quality factor MKIDs with Q i up to 600,000.
The sensitivity of a kinetic inductance detector is determined by the performance of the cavity circuit and therefore a high quality factor and low phase noise are required. We developed superconducting niobium coplanar waveguide resonators for kinetic inductance detectors at a resonance frequency of 6 GHz. The length of the resonators is adjusted to a quarter of a wavelength which corresponds to ≈ 5.3 mm in our geometry. Different layouts with coplanar waveguide transmission line topology for the resonator were designed and simulated. Some parameters of the device fabrication process were varied. The niobium thin films were deposited by magnetron sputtering on sapphire substrates kept at ambient temperature. The resonators were patterned by photolithography and reactive ion etching and measured at helium temperatures. Because of the quarter wave geometry with one shorted end the reflection parameter was measured. We have studied the influence of the coupling capacitances on quality factor. The optimization includes microwave simulations and implementation in different resonator structures. The measurements of optimized devices showed a very high quality factor above one million (10 6 ). The obtained results and perspective on further development of resonators will be discussed.
We characterize niobium nitride (NbN) λ/2 coplanar waveguide resonators, which were fabricated from a 10-nm-thick film on silicon dioxide grown by sputter deposition. For films grown at 180 °C, we report a superconducting critical temperature of 7.4 K associated with a normal square resistance of 1 kΩ, leading to a kinetic inductance of 192 pH/◻. We fabricated resonators with a characteristic impedance up to 4.1 kΩ and internal quality factors Qi>104 in the single photon regime at zero magnetic field. Moreover, in the many photon regime, the resonators present a high magnetic field resilience with Qi>104 in a 6 T in-plane magnetic field and in a 300 mT out-of-plane magnetic field. These findings make such resonators a compelling choice for circuit quantum electrodynamics experiments involving quantum systems with small electric dipole moments operated in finite magnetic fields.
Superconducting qubits are a promising platform for large-scale quantum computing. Besides the Josephson junction, most parts of a superconducting qubit are made of a planar, patterned superconducting thin films. In the past, most qubit architectures have relied on niobium (Nb) as the material of choice for the superconducting layer. However, there is also a variety of alternative materials with potentially less losses, which may thereby result in increased qubit performance. One such material is tantalum (Ta), for which high-performance qubit components have already been demonstrated. In this study, we report the sputter-deposition of Ta thin films directly on heated and unheated silicon (Si) substrates as well as onto different, nanometer-thin seed layers from tantalum nitride (TaN), titanium nitride (TiN) or aluminum nitride (AIN) that were deposited first. The thin films are characterized in terms of surface morphology, crystal structure, phase composition, critical temperature, residual resistance ratio (RRR) and RF-performance. We obtain thin films indicative of pure alpha-Ta for high temperature (600°C) sputtering directly on silicon and for Ta deposited on TaN or TiN seed layers. Coplanar waveguide (CPW) resonator measurements show that the Ta deposited directly on the heated silicon substrate performs best with internal quality factors Qi reaching 1xl06in the single-photon regime, measured at T=100 mK.
Abstract A quarter wavelength superconducting aluminum film coplanar waveguide resonator with a high-quality factor was designed and fabricated. Furthermore, its resonant frequency and quality as a function of temperatures and exciting powers were investigated. The experimental results showed that the resonance frequency decreases about 1% with the increase of temperature from 50 mk to 1 K, and the load quality factor of the resonator also decreases. The resonant frequency decreases with power from − 120 to − 70 dBm. The quality factor increases with increased excitation power due to the loss decreases and nonlinearity. The results are consistent with the theoretical analysis of the surface impedance model.
High-quality superconducting coplanar waveguide (SCPW) resonators are crucial for developing superconducting quantum information devices and sensors. We designed quarter-wavelength SCPW resonators and fabricated the SCPW resonators using Nb thin film. The resonant characteristics were measured at T = 4.2 K, revealing the intrinsic quality factor and the coupling quality factor to be Qi = 4,784 and Qc = 17, 980, respectively. Our design and fabrication techniques would be very useful to develop a gate-tunable superconducting qubit based on the semiconductor nanostructures.