Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

二重SQUID構造を採用した単一磁束量子ディジタル信号増幅回路の研究

孔明 樋口

Published Mar 25, 2019• 0 citations
OpenAlex

Abstract

単一磁束量子を情報担体とした単一磁束量子(RSFQ: Rapid Single-Flux-Quantum) 回路は、その高速性と優れた低消費電力性から次世代の回路としての期待がされており、研究が盛んに進められている。しかしSFQの持つエネルギーの低さから低温のSFQ回路と室温の半導体回路を繋ぐインターフェース回路が必要となる。以上の理由からオンチップRSFQ回路出力増幅回路の研究が進められている。その中の1つに分布型アンプがある。この回路は従来の増幅回路と伝送線路の技術を組み合わせることで広帯域幅と高利得の両立を可能にした回路であり、超伝導回路での先行研究もされている。この先行研究では正常に動作を観測したが出力振幅が小さく、室温環境との通信ではより高い振幅電圧を得る必要がある。そこで本研究はオンチップRSFQ分布型アンプの出力電圧向上に向けた改良を行い、その特性を評価することを研究目的とした。出力電圧の向上のため、我々はアンプ1段あたりのSQUID の数を1個から2個に増やした。この変更により、理想的には出力振幅が2倍に増加すると期待される。以降先行研究のSQUIDが1 個の分布型アンプを単一SQUID構造分布型アンプ、我々が設計したSQUIDが2個の分布型アンプを二重SQUID構造分布型アンプと記載する。数値計算での結果では4 段二重SQUID構造分布型アンプの最大出力振幅は3.54mVとなり、4 段単一SQUID構造のそれと比較して2.07倍に増加した。最大動作周波数は9.5Gbpsと求まった。段数を12段、24段に増やした回路も設計し、それぞれ最大出力振幅10.15mV、19.55mVを得た。単一SQUID構造の回路と比較してそれぞれ2.00倍、1.96倍に振幅は増加した。その後4 段のRSFQ分布型アンプを試作、低速測定を行った。測定では二重SQUID構造分布型アンプの最大出力振幅は2.93mVとなり、単一SQUID構造のそれと比較して1.51 倍に増加した。4 段二重SQUID構造分布型アンプの動作を確認したため、12 段と24段二重SQUID構造分布型アンプの低速測定と高速測定も実施した。低速測定結果では12 段二重SQUID構造分布型アンプの最大出力振幅は8.23mV、24段では14.50mV であったが、数値計算と比較するとバイアス電流に対する動作領域と最大出力振幅のどちらも低いという結果になった。同様に高速測定を実施したが、完全な動作とはならず部分的に動作していることが確認できる程度に留まった。今後は高速測定での完全動作を目指して改良を重ねていく予定である。

Related papers

単一磁束量子の2進パルス列を用いたD/A変換器の研究

直功 瀬賀

単一磁束量子(Single Flux Quantum)を用いた超伝導回路であるRSFQ(Rapid-SFQ)回路は、100GHzを超える帯域およびCMOS の1/1000以下の消費電力であることから、次世代の基盤技術として研究されている。SFQ回路の動作原理となるJosephson効果では、SFQがジョセフソン接合を通過する際に、その通過周波数に比例する高精度電圧が出力されることが示されている。この電圧は量子力学で保証される高精度電圧標準そのため、直流の一次電圧標準として用いられている。一方、交流の一次標準の作成にはいまだに至っておらず、研究が行われている。高精度交流電圧出力の方式として、RSFQ回路上でSFQパルス列の周波数可変回路を作製することによって、任意電圧の出力を行う周波数変調型RSFQ Digital-to-Analog Converter(DAC)などが研究されている。その中でも本研究ではSum of selected bit sequence(Σ-SBS)型のRSFQ-DACに着目した。Σ-SBS型RSFQ-DACは、SFQパルス列を2のべき乗のパルス列に分割し、指定されたパルス列のみを合成することで、2進数で表されたデータに対応する出力SFQパルス列を生成する。先行研究では6bit Σ-SBS RSFQ-DAC が設計および試作され、1.7μVまでの出力電圧で正常動作が確認された。しかし、計算上の動作限界では23μV程度が期待されていたため、想定よりも出力が低いことが報告された。そこで本研究では、先行研究で示されたΣ-SBSの最大動作速度を向上させるため、改良及び回路機構の変更を行った。主要な回路調整として、SFQパルス列の合成に対して適切な遅延を介することで、SFQパルス列同士の合成時に衝突を起こす頻度を減少させる機構を提案した。また、入力データの最上位ビット(Most Significant Bit:MSB)を分離することで動作速度の向上及び正負両極動作を行う機構も提案した。設計されたΣ-SBS RSFQ-DACでは最大出力電圧は244μVとなり、数値計算によって得られた最大出力電圧の259.8μVに対して94%程の動作が確認された。この結果は先行研究の1.7μVの144倍となった。また、MSB分離型4bitΣ-SBSは差動アンプを介して正負両極動作の測定を行い、-260μVから230μまでの両極動作が確認された。本研究では8bitなどの高段での設計も同様に行ったが、正常動作が得られなかった。今後の目標として、回路を構成するセルライブラリなどの再設計を行うことで動作マージンを広げていく必要があると考えた。

•Mar 24, 2022•0 citations

Design and Demonstration of Interface Circuits Between Rapid Single-Flux-Quantum and Adiabatic Quantum-Flux-Parametron Circuits

Fumihiro China, Tatsuya Narama, Naoki Takeuchi +3 more

We investigated interface circuits between rapid single-flux-quantum (RSFQ) circuits and adiabatic quantum-flux-parametron (AQFP) circuits for a high-speed and low-power hybrid computing system. In addition, the interface circuits allow us to use long-distance interconnections based on single-flux-quantum (SFQ) passive transmission lines between AQFP gates. The target frequency of interface circuits is several gigahertz. There are two types of interface circuits. The RSFQ/AQFP interface circuit, which transmits a signal from RSFQ circuits to AQFP gates, was realized by coupling an RSFQ toggle flip-flop (TFF) to an AQFP buffer gate. The simulated bias margins of the RSFQ TFF and the excitation current margin of the RSFQ/AQFP interface were 2.22 mA ± 24.7% and 1.71 mA ± 25.0%, respectively. The AQFP/RSFQ interface circuit, which transmits a signal from AQFP gates to RSFQ circuits, was designed by using a high-sensitive magnetically coupled dc/SFQ converter (MC-dc/SFQ) to detect an output current of an AQFP buffer gate. The simulated bias margins of the MC-dc/SFQ and the excitation current margin of the AQFP/RSFQ interface were 0.558 mA ± 20.5% and 1.95 mA ± 36.1%, respectively. We also fabricated and measured the interface circuits.

IEEE Transactions on Applied Superconductivity•Jun 7, 2016•19 citations

オシレータのタイミングジッタを利用して真性乱数を生成する超伝導集積回路

健太 佐藤

単一磁束量子(Single Flux Quantum:SFQ)回路は超伝導回路の一つであり,次世代型集積回路として注目されている.その一つに乱数生成回路(Hardware Random Number Generator: HRNG)が挙げられる.HRNGは完全にランダムな真性乱数の生成が可能で,セキュリティなどの分野で必要とされている.SFQ回路によるHRNGの先行研究では,高速に発振するオシレータからの信号と乱数生成信号の時間的ゆらぎ(タイミングジッタ)を比較して真性乱数を生成した.本研究では,複数のオシレータそれぞれのタイミングジッタを利用してオシレータ周波数の変動に耐性のある複数のオシレータによるHRNGを提案し,その性能評価を行った.オシレータが3つのTriple-Oscillator HRNG (TRO-HRNG)と2つのTwin-Oscillator HRNG (TO-HRNG) を設計し,数値計算で性能を評価した.TO-HRNGは測定も実施した. TRO-HRNGはClock OscillatorとGate Oscillator1,Gate Oscillator2の3つのオシレータで構成される.数値計算では,1の出現確率についてXORゲートの入力端子へ接続されるGate Oscillator1とGate Oscillator2それぞれの発振周波数 fgate1,fgate2 を交換した場合,1の出現確率に差があった.また,Clock Oscillatorの発振周波数を固定した場合,fgate1とfgate2の差の絶対値が大きいほど1の出現確率が大きくなった.検定合格率に関してClock Oscillatorの発振周波数が50GHzとき,乱数検定であるFIPS 140-2は,|fgate1-fgate2|が約10GHzのとき検定に100%で合格した. TO-HRNGはClock OscillatorとGate Oscillatorの2つで構成される.シミュレーションの結果について,1の出現確率に関してはClock OscillatorとGate Oscillatorそれぞれの発振周波数 fclk, fgate が近しいとき1の出現確率が極小となった.検定合格率について1の出現確率が50%近傍となる周波数条件で概ね100%の合格率であったが,fclk=60GHzでは6.31GHzの生成速度において合格率が100%でなかった.生成速度が最も大きくなった周波数条件はfclk=40GHzであった.実験による測定では,周波数条件が変化しても1の出現確率が大きく変動しなかった.検定合格率も90%以上であった.先行研究よりも周波数の変更に対して耐性があった.SP 800-22による評価では,12個のテストのうち9個のテストで合格していた. TRO-HRNGとTO-HRNGを比較した結果,TRO-HRNGの方が1の出現確率が大きく,周波数条件を変更したときの1の出現確率の変動も小さかった.

•Mar 24, 2023•0 citations

The development and characterisation of a parameterised RSFQ cell library for layout synthesis

Lieze Schindler

ENGLISH ABSTRACT: Superconductor electronics have shown great promise for interfacing quantum computers to conventional electronics. Several superconductor logic families show potential, \nbut one particular logic family has shown reliable results: Rapid Single Flux Quantum \n(RSFQ). RSFQ logic implements single SFQ pulses to represent binary data instead of \nthe traditional voltage levels used by semiconductor electronics. RSFQ is so ubiquitous \nto superconductor digital systems that it serves as the entry to superconductor digital \ndesign. Presently, however, the field of RSFQ logic cell design is very exclusive with \na small number of physicists and engineers able to design efficient RSFQ cells. This \nresearch aims to provide a formalised RSFQ design methodology with education quality \ncircuit theory. Several RSFQ examples are designed, analysed and improved using phasebased circuit equations. Similar to Kirchhoff’s current and voltage laws, these phase-based \nequations can be used to accurately determine the current distribution within a cell. The \ndesign methodology for multi-state RSFQ cells is also discussed. Multiple simulation \nmethods confirming cell functionality and operating margins are also presented. The \neducation regarding the design, analysis and implementation of RSFQ cells is vastly \nexpanded through this research which can accelerate the field of quantum circuit design. \nRSFQ cells can be connected using a non-storing inductive loop, Josephson transmission lines (JTLs) or, alternatively, superconductor passive transmission lines (PTLs) \nto bridge longer distances. Signal transmission of SFQ pulses through PTLs and JTLs \nare analysed and compared. Impedance matching for PTL interconnects to reduce pulse \nreflection is also investigated. \nAn example of a portable RSFQ cell library for layout synthesis is developed as \npart of the IARPA SuperTools program. The challenges of RSFQ cell layouts for the \nMassachusetts Institute of Technology Lincoln Laboratory (MIT-LL) SFQ5ee fabrication \nprocess are discussed. A methodology for establishing a standardised cell layout synthesis \nis presented. The research contributes to the design and characterisation of track routing \narchitecture for RSFQ on a multilayer fabrication process. \nLastly, methods to test fabricated RSFQ circuits are presented. This includes testing \nthe functionality of individual cells, as well as measuring throughput delays. As the SFQ \npulses are only a few picoseconds wide, it is not possible to observe these pulses using \nconventional measuring equipment. The fabricated tests must therefore be designed in \nsuch a way that it is possible to extract meaningful measurements.

•Mar 1, 2021•3 citations

低発熱型SQUIDとFPGAを用いた超伝導遷移端型X線マイクロカロリメータのための周波数分割方式信号多重化装置の開発(超伝導センシング基盤技術及びその応用,一般)

和広 酒井, 洋 竹井, 亮 山本 +6 more

電子情報通信学会技術研究報告. SCE, 超伝導エレクトロニクス•Sep 25, 2013•0 citations

高温rf SQUID的电压—电流特性曲线

何东风, 王继纯

对于采用电感耦合谐振回路的200MHz 高温超导YBCOrfSQUID 系统,我们测量了它的输出电压偏置电流幅度的特性曲线( 即VTIrf 曲线) ,发现当rf SQUID 工作在非回滞模式并且采用混频器作为检波器时,曲线的形状与通常所观察到的VTIrf 曲线有显著的不同,我们认为这是相位信号和振幅信号共同作用的结果,根据这一思想我们选用高温超导rf SQUID参数并利用低温超导rf SQUID 理论进行一些模拟计算,获得和实验非常一致的结果,这说明低温超导rf SQUID 理论仍可用来解释一些高温超导rf SQUID实验现象

Diwen wuli xuebao•Jan 1, 1999•0 citations
単一磁束量子を情報担体とした単一磁束量子(RSFQ: Rapid Single-Flux-Quantum) 回路は、その高速性と優れた低消費電力性から次世代の回路としての期待がされており、研究が盛んに進められている。しかしSFQの持つエネルギーの低さから低温のSFQ回路と室温の半導体回路を繋ぐインターフェース回路が必要となる。以上の理由からオンチップRSFQ回路出力増幅回路の研究が進められている。その中の1つに分布型アンプがある。この回路は従来の増幅回路と伝送線路の技術を組み合わせることで広帯域幅と高利得の両立を可能にした回路であり、超伝導回路での先行研究もされている。この先行研究では正常に動作を観測したが出力振幅が小さく、室温環境との通信ではより高い振幅電圧を得る必要がある。そこで本研究はオンチップRSFQ分布型アンプの出力電圧向上に向けた改良を行い、その特性を評価することを研究目的とした。出力電圧の向上のため、我々はアンプ1段あたりのSQUID の数を1個から2個に増やした。この変更により、理想的には出力振幅が2倍に増加すると期待される。以降先行研究のSQUIDが1 個の分布型アンプを単一SQUID構造分布型アンプ、我々が設計したSQUIDが2個の分布型アンプを二重SQUID構造分布型アンプと記載する。数値計算での結果では4 段二重SQUID構造分布型アンプの最大出力振幅は3.54mVとなり、4 段単一SQUID構造のそれと比較して2.07倍に増加した。最大動作周波数は9.5Gbpsと求まった。段数を12段、24段に増やした回路も設計し、それぞれ最大出力振幅10.15mV、19.55mVを得た。単一SQUID構造の回路と比較してそれぞれ2.00倍、1.96倍に振幅は増加した。その後4 段のRSFQ分布型アンプを試作、低速測定を行った。測定では二重SQUID構造分布型アンプの最大出力振幅は2.93mVとなり、単一SQUID構造のそれと比較して1.51 倍に増加した。4 段二重SQUID構造分布型アンプの動作を確認したため、12 段と24段二重SQUID構造分布型アンプの低速測定と高速測定も実施した。低速測定結果では12 段二重SQUID構造分布型アンプの最大出力振幅は8.23mV、24段では14.50mV であったが、数値計算と比較するとバイアス電流に対する動作領域と最大出力振幅のどちらも低いという結果になった。同様に高速測定を実施したが、完全な動作とはならず部分的に動作していることが確認できる程度に留まった。今後は高速測定での完全動作を目指して改良を重ねていく予定である。
単一磁束量子(Single Flux Quantum)を用いた超伝導回路であるRSFQ(Rapid-SFQ)回路は、100GHzを超える帯域およびCMOS の1/1000以下の消費電力であることから、次世代の基盤技術として研究されている。SFQ回路の動作原理となるJosephson効果では、SFQがジョセフソン接合を通過する際に、その通過周波数に比例する高精度電圧が出力されることが示されている。この電圧は量子力学で保証される高精度電圧標準そのため、直流の一次電圧標準として用いられている。一方、交流の一次標準の作成にはいまだに至っておらず、研究が行われている。高精度交流電圧出力の方式として、RSFQ回路上でSFQパルス列の周波数可変回路を作製することによって、任意電圧の出力を行う周波数変調型RSFQ Digital-to-Analog Converter(DAC)などが研究されている。その中でも本研究ではSum of selected bit sequence(Σ-SBS)型のRSFQ-DACに着目した。Σ-SBS型RSFQ-DACは、SFQパルス列を2のべき乗のパルス列に分割し、指定されたパルス列のみを合成することで、2進数で表されたデータに対応する出力SFQパルス列を生成する。先行研究では6bit Σ-SBS RSFQ-DAC が設計および試作され、1.7μVまでの出力電圧で正常動作が確認された。しかし、計算上の動作限界では23μV程度が期待されていたため、想定よりも出力が低いことが報告された。そこで本研究では、先行研究で示されたΣ-SBSの最大動作速度を向上させるため、改良及び回路機構の変更を行った。主要な回路調整として、SFQパルス列の合成に対して適切な遅延を介することで、SFQパルス列同士の合成時に衝突を起こす頻度を減少させる機構を提案した。また、入力データの最上位ビット(Most Significant Bit:MSB)を分離することで動作速度の向上及び正負両極動作を行う機構も提案した。設計されたΣ-SBS RSFQ-DACでは最大出力電圧は244μVとなり、数値計算によって得られた最大出力電圧の259.8μVに対して94%程の動作が確認された。この結果は先行研究の1.7μVの144倍となった。また、MSB分離型4bitΣ-SBSは差動アンプを介して正負両極動作の測定を行い、-260μVから230μまでの両極動作が確認された。本研究では8bitなどの高段での設計も同様に行ったが、正常動作が得られなかった。今後の目標として、回路を構成するセルライブラリなどの再設計を行うことで動作マージンを広げていく必要があると考えた。
We investigated interface circuits between rapid single-flux-quantum (RSFQ) circuits and adiabatic quantum-flux-parametron (AQFP) circuits for a high-speed and low-power hybrid computing system. In addition, the interface circuits allow us to use long-distance interconnections based on single-flux-quantum (SFQ) passive transmission lines between AQFP gates. The target frequency of interface circuits is several gigahertz. There are two types of interface circuits. The RSFQ/AQFP interface circuit, which transmits a signal from RSFQ circuits to AQFP gates, was realized by coupling an RSFQ toggle flip-flop (TFF) to an AQFP buffer gate. The simulated bias margins of the RSFQ TFF and the excitation current margin of the RSFQ/AQFP interface were 2.22 mA ± 24.7% and 1.71 mA ± 25.0%, respectively. The AQFP/RSFQ interface circuit, which transmits a signal from AQFP gates to RSFQ circuits, was designed by using a high-sensitive magnetically coupled dc/SFQ converter (MC-dc/SFQ) to detect an output current of an AQFP buffer gate. The simulated bias margins of the MC-dc/SFQ and the excitation current margin of the AQFP/RSFQ interface were 0.558 mA ± 20.5% and 1.95 mA ± 36.1%, respectively. We also fabricated and measured the interface circuits.
単一磁束量子(Single Flux Quantum:SFQ)回路は超伝導回路の一つであり,次世代型集積回路として注目されている.その一つに乱数生成回路(Hardware Random Number Generator: HRNG)が挙げられる.HRNGは完全にランダムな真性乱数の生成が可能で,セキュリティなどの分野で必要とされている.SFQ回路によるHRNGの先行研究では,高速に発振するオシレータからの信号と乱数生成信号の時間的ゆらぎ(タイミングジッタ)を比較して真性乱数を生成した.本研究では,複数のオシレータそれぞれのタイミングジッタを利用してオシレータ周波数の変動に耐性のある複数のオシレータによるHRNGを提案し,その性能評価を行った.オシレータが3つのTriple-Oscillator HRNG (TRO-HRNG)と2つのTwin-Oscillator HRNG (TO-HRNG) を設計し,数値計算で性能を評価した.TO-HRNGは測定も実施した. TRO-HRNGはClock OscillatorとGate Oscillator1,Gate Oscillator2の3つのオシレータで構成される.数値計算では,1の出現確率についてXORゲートの入力端子へ接続されるGate Oscillator1とGate Oscillator2それぞれの発振周波数 fgate1,fgate2 を交換した場合,1の出現確率に差があった.また,Clock Oscillatorの発振周波数を固定した場合,fgate1とfgate2の差の絶対値が大きいほど1の出現確率が大きくなった.検定合格率に関してClock Oscillatorの発振周波数が50GHzとき,乱数検定であるFIPS 140-2は,|fgate1-fgate2|が約10GHzのとき検定に100%で合格した. TO-HRNGはClock OscillatorとGate Oscillatorの2つで構成される.シミュレーションの結果について,1の出現確率に関してはClock OscillatorとGate Oscillatorそれぞれの発振周波数 fclk, fgate が近しいとき1の出現確率が極小となった.検定合格率について1の出現確率が50%近傍となる周波数条件で概ね100%の合格率であったが,fclk=60GHzでは6.31GHzの生成速度において合格率が100%でなかった.生成速度が最も大きくなった周波数条件はfclk=40GHzであった.実験による測定では,周波数条件が変化しても1の出現確率が大きく変動しなかった.検定合格率も90%以上であった.先行研究よりも周波数の変更に対して耐性があった.SP 800-22による評価では,12個のテストのうち9個のテストで合格していた. TRO-HRNGとTO-HRNGを比較した結果,TRO-HRNGの方が1の出現確率が大きく,周波数条件を変更したときの1の出現確率の変動も小さかった.
ENGLISH ABSTRACT: Superconductor electronics have shown great promise for interfacing quantum computers to conventional electronics. Several superconductor logic families show potential, \nbut one particular logic family has shown reliable results: Rapid Single Flux Quantum \n(RSFQ). RSFQ logic implements single SFQ pulses to represent binary data instead of \nthe traditional voltage levels used by semiconductor electronics. RSFQ is so ubiquitous \nto superconductor digital systems that it serves as the entry to superconductor digital \ndesign. Presently, however, the field of RSFQ logic cell design is very exclusive with \na small number of physicists and engineers able to design efficient RSFQ cells. This \nresearch aims to provide a formalised RSFQ design methodology with education quality \ncircuit theory. Several RSFQ examples are designed, analysed and improved using phasebased circuit equations. Similar to Kirchhoff’s current and voltage laws, these phase-based \nequations can be used to accurately determine the current distribution within a cell. The \ndesign methodology for multi-state RSFQ cells is also discussed. Multiple simulation \nmethods confirming cell functionality and operating margins are also presented. The \neducation regarding the design, analysis and implementation of RSFQ cells is vastly \nexpanded through this research which can accelerate the field of quantum circuit design. \nRSFQ cells can be connected using a non-storing inductive loop, Josephson transmission lines (JTLs) or, alternatively, superconductor passive transmission lines (PTLs) \nto bridge longer distances. Signal transmission of SFQ pulses through PTLs and JTLs \nare analysed and compared. Impedance matching for PTL interconnects to reduce pulse \nreflection is also investigated. \nAn example of a portable RSFQ cell library for layout synthesis is developed as \npart of the IARPA SuperTools program. The challenges of RSFQ cell layouts for the \nMassachusetts Institute of Technology Lincoln Laboratory (MIT-LL) SFQ5ee fabrication \nprocess are discussed. A methodology for establishing a standardised cell layout synthesis \nis presented. The research contributes to the design and characterisation of track routing \narchitecture for RSFQ on a multilayer fabrication process. \nLastly, methods to test fabricated RSFQ circuits are presented. This includes testing \nthe functionality of individual cells, as well as measuring throughput delays. As the SFQ \npulses are only a few picoseconds wide, it is not possible to observe these pulses using \nconventional measuring equipment. The fabricated tests must therefore be designed in \nsuch a way that it is possible to extract meaningful measurements.
对于采用电感耦合谐振回路的200MHz 高温超导YBCOrfSQUID 系统,我们测量了它的输出电压偏置电流幅度的特性曲线( 即VTIrf 曲线) ,发现当rf SQUID 工作在非回滞模式并且采用混频器作为检波器时,曲线的形状与通常所观察到的VTIrf 曲线有显著的不同,我们认为这是相位信号和振幅信号共同作用的结果,根据这一思想我们选用高温超导rf SQUID参数并利用低温超导rf SQUID 理论进行一些模拟计算,获得和实验非常一致的结果,这说明低温超导rf SQUID 理论仍可用来解释一些高温超导rf SQUID实验现象