Multiplexed quantum transport using commercial off-the-shelf CMOS at sub-kelvin temperatures
Brian Paquelet Wuetz, Peter L. Bavdaz, LaReine A. Yeoh, Raymond N. Schouten, H. van der Does, M. Tiggelman, Diego Sabbagh, Amir Sammak, C.G. Almudever, Fabio Sebastiano, J. S. Clarke, Menno Veldhorst, Giordano Scappucci
Continuing advancements in quantum information processing have caused a paradigm shift from research mainly focused on testing the reality of quantum mechanics to engineering qubit devices with numbers required for practical quantum computation.One of the major challenges in scaling toward large-scale solid-state systems is the limited input/output (I/O) connectors present in cryostats operating at sub-kelvin temperatures required to execute quantum logic with high-fidelity.This interconnect bottleneck is equally present in the device fabrication-measurement cycle, which requires high-throughput and cryogenic characterization to develop quantum processors.Here we multiplex quantum transport of two-dimensional electron gases at sub-kelvin temperatures.We use commercial off-the-shelf CMOS multiplexers to achieve an order of magnitude increase in the number of wires.Exploiting this technology we advance 300 mm epitaxial wafers manufactured in an industrial CMOS fab to a record electron mobility of (3.9±0.6)×10 5 cm 2 /Vs and percolation density of (6.9±0.4)×10 10 cm -2 , representing a key step toward large silicon qubit arrays.We envision that the demonstration will inspire the development of cryogenic electronics for quantum information and because of the simplicity of assembly, low-cost, yet versatility, we foresee widespread use of similar cryo-CMOS circuits for high-throughput quantum measurements and control of quantum engineered systems.
Continuing advancements in quantum information processing have caused a paradigm shift from research mainly focused on testing the reality of quantum mechanics to engineering qubit devices with numbers required for practical quantum computation.One of the major challenges in scaling toward large-scale solid-state systems is the limited input/output (I/O) connectors present in cryostats operating at sub-kelvin temperatures required to execute quantum logic with high-fidelity.This interconnect bottleneck is equally present in the device fabrication-measurement cycle, which requires high-throughput and cryogenic characterization to develop quantum processors.Here we multiplex quantum transport of two-dimensional electron gases at sub-kelvin temperatures.We use commercial off-the-shelf CMOS multiplexers to achieve an order of magnitude increase in the number of wires.Exploiting this technology we advance 300 mm epitaxial wafers manufactured in an industrial CMOS fab to a record electron mobility of (3.9±0.6)×10 5 cm 2 /Vs and percolation density of (6.9±0.4)×10 10 cm -2 , representing a key step toward large silicon qubit arrays.We envision that the demonstration will inspire the development of cryogenic electronics for quantum information and because of the simplicity of assembly, low-cost, yet versatility, we foresee widespread use of similar cryo-CMOS circuits for high-throughput quantum measurements and control of quantum engineered systems.
Abstract Continuing advancements in quantum information processing have caused a paradigm shift from research mainly focused on testing the reality of quantum mechanics to engineering qubit devices with numbers required for practical quantum computation. One of the major challenges in scaling toward large-scale solid-state systems is the limited input/output (I/O) connectors present in cryostats operating at sub-kelvin temperatures required to execute quantum logic with high fidelity. This interconnect bottleneck is equally present in the device fabrication-measurement cycle, which requires high-throughput and cryogenic characterization to develop quantum processors. Here we multiplex quantum transport of two-dimensional electron gases at sub-kelvin temperatures. We use commercial off-the-shelf CMOS multiplexers to achieve an order of magnitude increase in the number of wires. Exploiting this technology, we accelerate the development of 300 mm epitaxial wafers manufactured in an industrial CMOS fab and report a remarkable electron mobility of (3.9 ± 0.6) × 105 cm2/Vs and percolation density of (6.9 ± 0.4) × 1010 cm−2, representing a key step toward large silicon qubit arrays. We envision that the demonstration will inspire the development of cryogenic electronics for quantum information, and because of the simplicity of assembly and versatility, we foresee widespread use of similar cryo-CMOS circuits for high-throughput quantum measurements and control of quantum engineered systems.
Quantum computing holds the potential to solve problems beyond the capabilities of classical computers. However, realizing practical large-scale quantum computers faces critical challenges, including the key bottleneck in wiring quantum processors operating at cryogenic temperatures to their room temperature control electronics. This article explores cryo-CMOS ICs as an enabling technology to circumvent such a wiring bottleneck. After reviewing the basics of quantum computing and the behavior of CMOS devices at cryogenic temperatures, the requirements for the interface electronics for superconducting and semiconductor qubits are discussed, and state-of-the-art cryo-CMOS circuit solutions are briefly described, including a few hints to other qubit platforms. Finally, the article concludes with an overview of future challenges to be addressed to realize the vision of cryo-CMOS technology as an enabler of large-scale quantum computers with practical applications.
Quantum computing promises an exponential speed-up of computation compared to what is nowadays achievable with classical computers. In this way, it enables the evaluation of more complex models and the breaching of current security algorithms. For the operation of a quantum system, many questions remain to be answered. Currently, there are several quantum technologies that promise to be both reliable and scalable, two features required for large scale quantum operations. Common to all technologies is the operating temperature that needs to be close to absolute zero, i.e. below 100 mK, to suppress environment noise and allow the quantum properties to become 'visible'. In order for any quantum processor to be operated, a so-called quantum-classical interface is required for the quantum bit (qubit) read-out and control. This interface consists of various electronic blocks, such as analog-to-digital converters, digital-to-analog converters, mixers, amplifiers and a digital controller. Especially the analog blocks require effort to meet the noise and stability constraints as not to disturb the very sensitive qubits and allow reading of the tiny signals. As the qubits live in extremely deep-cryogenic temperatures, long wires interface the cryogenic with the room temperature environment, where most of the electronics is situated. However, for a scalable system, heat injection becomes a serious problem, with many wires between 300 K and sub-Kelvin. Furthermore, such amount of interconnects is challenging to mechanically place in a dilution refrigerator. Therefore, in this work, we propose to implement the electronics not at room temperature, but at a temperature much closer to the qubits, for example at 4 K. This not only reduces significantly the wiring between room temperature and the qubits, but we can also benefit from lower electronic noise at such a temperature. The operation of conventional electronics almost 200°C below its normal temperature range is not trivial as device properties alter significantly and most circuits no longer operate as intended. In CMOS processes, the main technology in the integrated electronics world, the behaviour of the transistors, required for the implementation of any circuit, deviates considerably at low temperatures. The transistor's threshold voltage goes up, the mobility increases and the subthreshold slope becomes steeper, to name just a few of these deviations. Although there are improvements in performance, there are also some counter effects, and characterization of the transistors is needed to observe the changes. Once devices are characterized at such low temperatures, new models can be built and circuits can be simulated and adapted to operate properly at cryogenic temperatures. Luckily, there are various commercially available devices that can already withstand the chills of cold. We demonstrated various commercially available devices, such as a field-programmable gate array (FPGA) implemented in a 28 nm CMOS process, to be operating without major concerns at 4~K. Its properties alter only slightly, within 5 to 10%, and all tested circuit implementations, working at 300~K, also worked at 4 K. We combined both commercially available devices, that operate 200 K below their specified temperature range, with custom designed CMOS circuits to implement a cryogenic read-out platform for spin qubits. This system comprises amplifiers, an ADC, an FPGA, voltage regulators and a clock generator. It allows to amplify the tiny signal from the qubits and digitize it directly in the FPGA in order to process the data locally at 4~K. This system is one of the first systematic attempts at operating a part of the quantum-classical interface at cryogenic temperatures and forms the basis for future systems comprising the complete electronic interface for qubits to operate at such low temperatures. One of the main problems to tackle for cryogenic electronic systems is their power consumption. Power budgets are simply limited to roughly 1 or 2 Watts at 4 K and exponentially lower at deeper cryogenic temperatures, thus limiting the size of large-scale electronic systems. Our approach of combined commercial and custom circuits will have to be steadily replaced by a single (custom) technology that meets both power and scalability constraints. One of the best candidates is CMOS, a technology that the industry has relied upon for several decades and benefits from many optimizations thanks to Moore's law.
Quantum computers1 could revolutionize computing in a profound way due to the massive speedup they promise. A quantum computer comprises a cryogenic quantum processor and a classical electronic controller. When scaling up the cryogenic quantum processor to at least a few thousands, and possibly millions, of qubits required for any practical quantum algorithm, cryogenic CMOS (cryo-CMOS) electronics is required to allow feasible and compact interconnections between the controller and the quantum processor. Cryo-CMOS leverages the CMOS fabrication infrastructure while exploiting the continuous improvement of performance and miniaturization guaranteed by Moore's law, in order to enable the fabrication of a cost-effective practical quantum computer. However, designing cryo-CMOS integrated circuits requires a new set of CMOS device models, their embedding in design and verification tools, and the possibility to co-simulate the cryo-CMOS/quantum-processor architecture for full-system optimization. In this paper, we address these challenges by focusing on their impact on the design of complex cryo-CMOS systems.
Abstract Large-scale superconducting quantum computing systems entail high-fidelity control and readout of large numbers of qubits at millikelvin temperatures, resulting in a massive input-output bottleneck. Cryo-electronics, based on complementary metal-oxide-semiconductor (CMOS) technology, may offer a scalable and versatile solution to overcome this bottleneck. However, detrimental effects due to cross-coupling between the electronic and thermal noise generated during cryo-electronics operation and the qubits need to be avoided. Here we present an ultra-low power radio-frequency (RF) multiplexing cryo-electronics solution operating below 15 mK that allows for control and interfacing of superconducting qubits with minimal cross-coupling. We benchmark its performance by interfacing it with a superconducting qubit and observe that the qubit’s relaxation times (T1) are unaffected, while the coherence times (T2) are only minimally affected in both static and dynamic operation. Using the multiplexer, single qubit gate fidelities above 99.9%, i.e., well above the threshold for surface-code based quantum error-correction, can be achieved with appropriate thermal filtering. In addition, we demonstrate the capability of time-division-multiplexed qubit control by dynamically windowing calibrated qubit control pulses. Our results show that cryo-CMOS multiplexers could be used to significantly reduce the wiring resources for large-scale qubit device characterization, large-scale quantum processor control and quantum error correction protocols.
The core of a quantum computer is a quantum processor, which is composed of quantum bits (qubits). Qubits can be implemented in many flavors, but they are fragile, and their state has a tendency to decay in time. To be usable for computation, qubits must be corrected in real time by a classical controller. The controller must also see that desired computations are executed. Today, the control of qubits is performed at room temperature (RT) by racks of instruments, while the qubits operate at several tens of milli-Kelvin. To ensure compactness and, eventually, scalability, we have proposed and implemented CMOS circuits designed to operate at a few degrees Kelvin. This makes complex thermalization circuits unnecessary, potentially enabling superconductive interconnects, which would enable virtually zero resistance and low thermal conductivity. Cryogenic CMOS, or cryo-CMOS, technology was chosen to achieve classical control due to its scalable nature and overall miniaturization opportunities. Cryo-CMOS circuits and systems need to be carefully designed to ensure strict power budgets, while achieving quite advanced specifications in terms of noise and bandwidth. We review the requirements of a classical controller and cryo-CMOS circuits and systems developed for spin qubits in our lab. Results and perspectives are presented with a discussion about a road map for the future.