Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Two-dimensional arrays of solid-state quantum memories

Mneimneh, Aya

Published Sep 9, 2024• 0 citations
OpenAlex

Abstract

Long-distance quantum communication relies on quantum repeaters to overcome the limitations of signal loss and decoherence. In quantum networks with repeater architecture, the distance nodes are entangled through entanglement swapping which is heralded using a classical signal. However, the entanglement rate is constrained by the travel time of heralding signals used in these repeaters. This thesis investigates the use of spatial multiplexing to address this limitation by dividing a solid-state crystal into 100 independent quantum memory cells. This multiplexing approach aims to enhance the entanglement rate by a factor of 100 and sets a new benchmark for solid-state systems. Building on previous work with one-dimensional solid-state AFC quantum memory \cite{Teller2024InPrep.}, this research involves designing and implementing an optical experimental setup to achieve 100 spatial modes, characterizing the two-dimensional array without the quantum memory. With the results of the characterization, the future performance of a quantum memory with the presented optical system is simulated.

Related papers

The experimental realization of long-lived quantum memory

Ran Zhao

Quantum communication between two remote locations often involves remote parties sharing an entangled quantum state. At present, entanglement distribution is usually performed using photons transmitted through optical fibers. However, the absorption of light in the fiber limits the communication distances to less than 200 km, even for optimal photon telecom wavelengths. To increase this distance, the quantum repeater idea was proposed. In the quantum repeater architecture, one divides communication distance into segments of the order of the attenuation length of the photons and places quantum memory nodes at the intermediate locations. Since the photon loss between intermediate locations is low, it is possible then to establish entanglement between intermediate quantum memory nodes. Once entanglement between adjacent nodes is established, one can extend it over larger distances using entanglement swapping.\n\nThe long coherence time of a quantum memory is a crucial requirement for the quantum repeater protocol. It is obvious that the coherence time of a quantum memory should be much longer that the time it takes for light to travel between remote locations. For a communication distance l = 1000 km, the corresponding time is t = l/c = 3.3 ms. One can show that for a simple repeater protocol and realistic success probabilities of entanglement generation, the required coherence time should be on the order of many seconds, while for the more complicated protocols that involve multiplexing and several quantum memory cells per intermediate node, the required coherence time is on the order of milliseconds.\n\nIn this thesis, I describe a quantum memory based on an ensemble of rubidium atoms confined in a one-dimensional optical lattice. The use of the magnetically- insensitive clock transition and suppression of atomic motion allows us to increase coherence time of the quantum memory by two-orders of magnitude compared to previous work. I also propose a method for determining the Zeeman content of atomic samples. In addition, I demonstrate the observation of quantum evolution under continuous measurement. The long quantum memory lifetime demonstrated in this work opens the way for scalable processing of quantum information and long distance quantum communication.

•Aug 3, 2010•0 citations

Long-distance quantum communication with single solid-state spins

Faezeh Kimiaee Asadi

Long-distance transfer of quantum information is an essential ability for many applications of quantum science. A natural choice to distribute quantum information is to encode it into photons and transfer it through optical fibers. However, due to the unavoidable transmission losses present in every communication channel, the distances for efficient quantum communication via direct-state transfer are limited to a few hundred kilometers. To overcome this limitation, the use of quantum repeaters has been suggested. A quantum repeater protocol aims to establish entanglement (i.e., quantum correlation) between remote nodes by first generating entanglement over shorter distance pieces, storing it in quantum memories, and finally extending it to the whole distance using entanglement swapping. The main goal of this thesis is to design quantum repeater architectures using single solid-state quantum emitters and to develop the two-qubit gates required for performing entanglement swapping. We first explain the basic ideas of quantum repeaters and introduce potential material candidates, single erbium (168Er) and europium (151Eu) ions doped yttrium orthosilicate photonic crystals. Next, we propose a quantum repeater scheme combing erbium and europium ions to generate and distribute entanglement over long distances. We study the entanglement generation rate of the protocol and compare it with the rate of a well-known ensemble-based quantum repeater. Then, using cavity assisted interactions, we propose three different schemes to perform high fidelity two-qubit gates between single quantum systems. We quantify their expected performance in detail by taking into account many realistic imperfections and compare their strengths and weaknesses. The ability to perform local two-qubits gates is especially crucial in terms of distributing entanglement. Finally, based on our gained knowledge through these projects, we propose our second quantum repeater architecture based on erbium (167Er) ions, which outperforms the first scheme. We study two possibilities for distributing entanglement and calculate the overall fidelity as well as the distribution rate of the protocol.

•Sep 18, 2020•0 citations

Distribution of light-matter quantum correlations with a temporally multiplexed solid-state quantum memory array

Aya Mneimneh, Susana Plascencia, Manuel Gundin +4 more

Multiplexed quantum memories increase the entanglement distribution rate in long-distance quantum repeater architectures by harnessing storage in several degrees of freedom. Here, we report on the distribution of light-matter quantum correlations using an array of time-multiplexed solid-state quantum memories. We store telecom-heralded single photons sequentially in up to ten memory cells using the full atomic frequency comb protocol with on-demand read-out in a Pr$^{3+}$:Y$_2$SiO$_5$ crystal. Leveraging both spatial and temporal multiplexing, we demonstrate quantum correlations between the telecom photon and up to 60 spatio-temporal modes of the quantum memory array. We then transmit the heralding telecom photon over 39.1 km of deployed optical fiber in the Metropolitan Area of Barcelona. In a realistic scenario where the generation rate is limited by the two-way communication time, we show that up to 15 % of the $393 μs$ round-trip communication time is filled with communication trials, leading to a 60-fold enhancement in the rate of detected telecom photons correlated with the quantum memory array, compared to a single-mode memory. With increased storage times and efficiencies, our multiplexed quantum memory array will constitute the backbone of a long-distance quantum network, establishing remote entanglement at high rates.

quant-pharXiv:2609.15689•Sep 15, 2026•0 citations

Towards long distance entanglement between a photon and a solid-state multimode quantum memory (Conference Presentation)

Jelena V. Rakonjac, Dario Lago-Rivera, Samuele Grandi +2 more

As the reach of quantum technologies extends ever further in communication and information science, a reliable way of transferring quantum information between distant locations becomes ever more crucial. While photons are widely accepted as excellent carriers due to their speed and low decoherence, losses of transmission (in free space or fibre) and the impossibility of cloning quantum information still pose a great challenge. The quantum repeater architecture was suggested as a solution to both problems [1]. In a quantum repeater the information encoded in an input state is transferred to a new one through entanglement swapping, that is then sent on along the channel. In this work we present our advances towards the realisation of a quantum repeater. Our system of choice combines a solid-state quantum memory with a source of photon pairs. The memory is based on a Rare-Earth Doped crystal, where quantum information can be stored in Pr3+ ions as a collective excitation using the Atomic Frequency Comb technique. On demand retrieval of the information is realised by transferring the excitation to a long-lived spin state. Record values of storage times and retrieval efficiencies have been demonstrated in this system [2]. Entangled pairs of single photons are generated by parametric down conversion in a periodically poled crystal placed inside a bow-tie cavity. This allows us to generate narrow band photons pairs, where the signal is spectrally matched to the memory (606nm), while the idler is in the telecom band [3]. Such a configuration allows us to benefit from the high performance of the memory, that also allows for temporal [2] and frequency [4] multimodality, while at the same time overcoming the high optical losses of 606nm photons by pair generation of a telecom photon. The first stepping stone, progress towards which is presented in this work, is the successful demonstration of energy-time entanglement between the telecom idler photon and the signal photon, stored as spin-wave excitation. The entanglement of the original pair is maintained by the memory temporal multimodality. The entanglement analysis will be made through time-bin qubit analysers made of a fibre-based Mach-Zehnder interferometer, for the former, and a solid-state equivalent based on two AFC with different storage times, for the latter [5]. In this direction we have already doubled the efficiency of the AFC storage protocols, that will be beneficial to count rates and signal-to-noise ratio. With respect to [2], we also increased the spectral-matching between the source and the memory [4]. Our experiment will provide an increase in storage time of 3 orders of magnitude with respect to previous demonstrations, as well as introducing for the first time on-demand read-out in a highly multi-mode memory. Demonstration of the successful transfer of quantum information between the signal photon and the long-lived solid-state excitation will open the way to the demonstration of long-distance entanglement between individual nodes in a quantum network.

SPIE Quantum Technologies•Apr 8, 2020•0 citations

Light-matter entanglement between telecom photons and solid-state quantum memories

Jelena V. Rakonjac

(English) Future networks for quantum communication will require a new form of technology in order to operate over long distances. The no-cloning theorem precludes the use of amplification, so quantum repeater schemes have been proposed to achieve long-distance quantum communication through the distribution of entanglement. A key device for this setup is a quantum memory, which is required in order to store entanglement and synchronise its distribution. Among the many physical systems than can be used as a quantum memory, rare-earth ion-doped crystals stand out due to their long coherence times and potential for multiplexing and integration. This thesis reports the use of one such system, Pr3+:Y2SiO5, as a quantum memory using the atomic frequency comb (AFC) protocol. Building on previous work, we improved the performance of the memory to be able to demonstrate light-matter entanglement with a telecommunications wavelength photon and the quantum memory, for both a bulk memory and an integrated version. To measure light-matter entanglement, we use photon pairs generated through cavity-enhanced spontaneous parametric down conversion, where one photon (the signal) is stored in the memory and the other (the idler) is at a telecommunications wavelength. These photon pairs exhibit energy-time entanglement, which we analyse in the time basis using fibre- and AFC-based Mach-Zehnder interferometers. In the first experiment, we demonstrate light-matter entanglement where the bulk quantum memory is used with on-demand retrieval via storage in a spin-wave. We measure interference fringes with average visibilities of 89(2)% for AFC storage, and 70(3)% for spin-wave storage, sufficient to demonstrate entanglement. This is the first such demonstration using an on-demand multimode solid-state memory and telecom photon. We show that entanglement is maintained for up to 47.7 µs of storage. These results were made possible through improvements in the AFC efficiency and the noise filtering. Furthermore, we perform on-demand storage and retrieval of up to 30 temporal modes. We take the next step towards implementing our system in a real world scenario by measuring entanglement over a distance. To do so, we send the idler photons through both optical fibre spools and deployed fibre in the metropolitan area of Barcelona, Spain, while the photon detection still occurs in the same lab. The resulting visibilities (80% or higher) demonstrate that the photonic qubit does not decohere during transmission through the optical fibre. We then decouple the photon creation and detection by measuring non-classical correlations between signal photons detected in the lab, and idler photons detected 16 km away (44 km in fibre) in a different location. The final experiment uses a fibre-integrated memory for light-matter entanglement. We use a Pr3+:Y2SiO5 crystal containing a Type I laser-written waveguide, interfaced directly with optical fibre. The fibre-integration allows for improved transmission and AFC efficiency compared to a free-space coupled waveguide memory. To analyse the performance of the memory, we demonstrate non-classical correlations for storage times up to 28 µs. We perform qubit tomography in the time basis for storage times of 3 and 10 µs, measuring two-qubit fidelities of 86(2)% and 86(4)%, respectively, demonstrating storage of entanglement. These experiments demonstrate the potential of our system for use as part of a quantum repeater, with many opportunities for further improvement to the storage time, efficiency, and multiplexing capability.

•Jun 26, 2023•0 citations

A solid-state temporally multiplexed quantum memory array at the single-photon level

Markus Teller, Susana Plascencia, Cristina Sastre Jachimska +2 more

Abstract The exploitation of multimodality in different degrees of freedom is one of the most promising ways to increase the rate of heralded entanglement between distant quantum nodes. In this paper, we realize a spatially-multiplexed solid-state quantum memory array with ten individually controllable spin-wave memory cells featuring on-demand read-out and temporal multiplexing. By combining spatial and temporal multiplexing, we store weak coherent pulses at the single-photon level in up to 250 spatio-temporal modes, with an average signal-to-noise ratio of 10(2). We perform a thorough characterization of the whole system, including its multiplexing and demultiplexing stage. We verify that the memory array exhibits low cross-talk even at the single-photon level. The measured performance indicates readiness for storing non-classical states and promises a speed-up in entanglement distribution rates.

arXiv:2507.12200•npj Quantum Information•Jun 4, 2025•18 citations
Long-distance quantum communication relies on quantum repeaters to overcome the limitations of signal loss and decoherence. In quantum networks with repeater architecture, the distance nodes are entangled through entanglement swapping which is heralded using a classical signal. However, the entanglement rate is constrained by the travel time of heralding signals used in these repeaters. This thesis investigates the use of spatial multiplexing to address this limitation by dividing a solid-state crystal into 100 independent quantum memory cells. This multiplexing approach aims to enhance the entanglement rate by a factor of 100 and sets a new benchmark for solid-state systems. Building on previous work with one-dimensional solid-state AFC quantum memory \cite{Teller2024InPrep.}, this research involves designing and implementing an optical experimental setup to achieve 100 spatial modes, characterizing the two-dimensional array without the quantum memory. With the results of the characterization, the future performance of a quantum memory with the presented optical system is simulated.
Quantum communication between two remote locations often involves remote parties sharing an entangled quantum state. At present, entanglement distribution is usually performed using photons transmitted through optical fibers. However, the absorption of light in the fiber limits the communication distances to less than 200 km, even for optimal photon telecom wavelengths. To increase this distance, the quantum repeater idea was proposed. In the quantum repeater architecture, one divides communication distance into segments of the order of the attenuation length of the photons and places quantum memory nodes at the intermediate locations. Since the photon loss between intermediate locations is low, it is possible then to establish entanglement between intermediate quantum memory nodes. Once entanglement between adjacent nodes is established, one can extend it over larger distances using entanglement swapping.\n\nThe long coherence time of a quantum memory is a crucial requirement for the quantum repeater protocol. It is obvious that the coherence time of a quantum memory should be much longer that the time it takes for light to travel between remote locations. For a communication distance l = 1000 km, the corresponding time is t = l/c = 3.3 ms. One can show that for a simple repeater protocol and realistic success probabilities of entanglement generation, the required coherence time should be on the order of many seconds, while for the more complicated protocols that involve multiplexing and several quantum memory cells per intermediate node, the required coherence time is on the order of milliseconds.\n\nIn this thesis, I describe a quantum memory based on an ensemble of rubidium atoms confined in a one-dimensional optical lattice. The use of the magnetically- insensitive clock transition and suppression of atomic motion allows us to increase coherence time of the quantum memory by two-orders of magnitude compared to previous work. I also propose a method for determining the Zeeman content of atomic samples. In addition, I demonstrate the observation of quantum evolution under continuous measurement. The long quantum memory lifetime demonstrated in this work opens the way for scalable processing of quantum information and long distance quantum communication.
Long-distance transfer of quantum information is an essential ability for many applications of quantum science. A natural choice to distribute quantum information is to encode it into photons and transfer it through optical fibers. However, due to the unavoidable transmission losses present in every communication channel, the distances for efficient quantum communication via direct-state transfer are limited to a few hundred kilometers. To overcome this limitation, the use of quantum repeaters has been suggested. A quantum repeater protocol aims to establish entanglement (i.e., quantum correlation) between remote nodes by first generating entanglement over shorter distance pieces, storing it in quantum memories, and finally extending it to the whole distance using entanglement swapping. The main goal of this thesis is to design quantum repeater architectures using single solid-state quantum emitters and to develop the two-qubit gates required for performing entanglement swapping. We first explain the basic ideas of quantum repeaters and introduce potential material candidates, single erbium (168Er) and europium (151Eu) ions doped yttrium orthosilicate photonic crystals. Next, we propose a quantum repeater scheme combing erbium and europium ions to generate and distribute entanglement over long distances. We study the entanglement generation rate of the protocol and compare it with the rate of a well-known ensemble-based quantum repeater. Then, using cavity assisted interactions, we propose three different schemes to perform high fidelity two-qubit gates between single quantum systems. We quantify their expected performance in detail by taking into account many realistic imperfections and compare their strengths and weaknesses. The ability to perform local two-qubits gates is especially crucial in terms of distributing entanglement. Finally, based on our gained knowledge through these projects, we propose our second quantum repeater architecture based on erbium (167Er) ions, which outperforms the first scheme. We study two possibilities for distributing entanglement and calculate the overall fidelity as well as the distribution rate of the protocol.
Multiplexed quantum memories increase the entanglement distribution rate in long-distance quantum repeater architectures by harnessing storage in several degrees of freedom. Here, we report on the distribution of light-matter quantum correlations using an array of time-multiplexed solid-state quantum memories. We store telecom-heralded single photons sequentially in up to ten memory cells using the full atomic frequency comb protocol with on-demand read-out in a Pr3+^{3+}3+:Y2_22​SiO5_55​ crystal. Leveraging both spatial and temporal multiplexing, we demonstrate quantum correlations between the telecom photon and up to 60 spatio-temporal modes of the quantum memory array. We then transmit the heralding telecom photon over 39.1 km of deployed optical fiber in the Metropolitan Area of Barcelona. In a realistic scenario where the generation rate is limited by the two-way communication time, we show that up to 15 % of the 393μs393 μs393μs round-trip communication time is filled with communication trials, leading to a 60-fold enhancement in the rate of detected telecom photons correlated with the quantum memory array, compared to a single-mode memory. With increased storage times and efficiencies, our multiplexed quantum memory array will constitute the backbone of a long-distance quantum network, establishing remote entanglement at high rates.
As the reach of quantum technologies extends ever further in communication and information science, a reliable way of transferring quantum information between distant locations becomes ever more crucial. While photons are widely accepted as excellent carriers due to their speed and low decoherence, losses of transmission (in free space or fibre) and the impossibility of cloning quantum information still pose a great challenge. The quantum repeater architecture was suggested as a solution to both problems [1]. In a quantum repeater the information encoded in an input state is transferred to a new one through entanglement swapping, that is then sent on along the channel. In this work we present our advances towards the realisation of a quantum repeater. Our system of choice combines a solid-state quantum memory with a source of photon pairs. The memory is based on a Rare-Earth Doped crystal, where quantum information can be stored in Pr3+ ions as a collective excitation using the Atomic Frequency Comb technique. On demand retrieval of the information is realised by transferring the excitation to a long-lived spin state. Record values of storage times and retrieval efficiencies have been demonstrated in this system [2]. Entangled pairs of single photons are generated by parametric down conversion in a periodically poled crystal placed inside a bow-tie cavity. This allows us to generate narrow band photons pairs, where the signal is spectrally matched to the memory (606nm), while the idler is in the telecom band [3]. Such a configuration allows us to benefit from the high performance of the memory, that also allows for temporal [2] and frequency [4] multimodality, while at the same time overcoming the high optical losses of 606nm photons by pair generation of a telecom photon. The first stepping stone, progress towards which is presented in this work, is the successful demonstration of energy-time entanglement between the telecom idler photon and the signal photon, stored as spin-wave excitation. The entanglement of the original pair is maintained by the memory temporal multimodality. The entanglement analysis will be made through time-bin qubit analysers made of a fibre-based Mach-Zehnder interferometer, for the former, and a solid-state equivalent based on two AFC with different storage times, for the latter [5]. In this direction we have already doubled the efficiency of the AFC storage protocols, that will be beneficial to count rates and signal-to-noise ratio. With respect to [2], we also increased the spectral-matching between the source and the memory [4]. Our experiment will provide an increase in storage time of 3 orders of magnitude with respect to previous demonstrations, as well as introducing for the first time on-demand read-out in a highly multi-mode memory. Demonstration of the successful transfer of quantum information between the signal photon and the long-lived solid-state excitation will open the way to the demonstration of long-distance entanglement between individual nodes in a quantum network.
(English) Future networks for quantum communication will require a new form of technology in order to operate over long distances. The no-cloning theorem precludes the use of amplification, so quantum repeater schemes have been proposed to achieve long-distance quantum communication through the distribution of entanglement. A key device for this setup is a quantum memory, which is required in order to store entanglement and synchronise its distribution. Among the many physical systems than can be used as a quantum memory, rare-earth ion-doped crystals stand out due to their long coherence times and potential for multiplexing and integration. This thesis reports the use of one such system, Pr3+:Y2SiO5, as a quantum memory using the atomic frequency comb (AFC) protocol. Building on previous work, we improved the performance of the memory to be able to demonstrate light-matter entanglement with a telecommunications wavelength photon and the quantum memory, for both a bulk memory and an integrated version. To measure light-matter entanglement, we use photon pairs generated through cavity-enhanced spontaneous parametric down conversion, where one photon (the signal) is stored in the memory and the other (the idler) is at a telecommunications wavelength. These photon pairs exhibit energy-time entanglement, which we analyse in the time basis using fibre- and AFC-based Mach-Zehnder interferometers. In the first experiment, we demonstrate light-matter entanglement where the bulk quantum memory is used with on-demand retrieval via storage in a spin-wave. We measure interference fringes with average visibilities of 89(2)% for AFC storage, and 70(3)% for spin-wave storage, sufficient to demonstrate entanglement. This is the first such demonstration using an on-demand multimode solid-state memory and telecom photon. We show that entanglement is maintained for up to 47.7 µs of storage. These results were made possible through improvements in the AFC efficiency and the noise filtering. Furthermore, we perform on-demand storage and retrieval of up to 30 temporal modes. We take the next step towards implementing our system in a real world scenario by measuring entanglement over a distance. To do so, we send the idler photons through both optical fibre spools and deployed fibre in the metropolitan area of Barcelona, Spain, while the photon detection still occurs in the same lab. The resulting visibilities (80% or higher) demonstrate that the photonic qubit does not decohere during transmission through the optical fibre. We then decouple the photon creation and detection by measuring non-classical correlations between signal photons detected in the lab, and idler photons detected 16 km away (44 km in fibre) in a different location. The final experiment uses a fibre-integrated memory for light-matter entanglement. We use a Pr3+:Y2SiO5 crystal containing a Type I laser-written waveguide, interfaced directly with optical fibre. The fibre-integration allows for improved transmission and AFC efficiency compared to a free-space coupled waveguide memory. To analyse the performance of the memory, we demonstrate non-classical correlations for storage times up to 28 µs. We perform qubit tomography in the time basis for storage times of 3 and 10 µs, measuring two-qubit fidelities of 86(2)% and 86(4)%, respectively, demonstrating storage of entanglement. These experiments demonstrate the potential of our system for use as part of a quantum repeater, with many opportunities for further improvement to the storage time, efficiency, and multiplexing capability.
Abstract The exploitation of multimodality in different degrees of freedom is one of the most promising ways to increase the rate of heralded entanglement between distant quantum nodes. In this paper, we realize a spatially-multiplexed solid-state quantum memory array with ten individually controllable spin-wave memory cells featuring on-demand read-out and temporal multiplexing. By combining spatial and temporal multiplexing, we store weak coherent pulses at the single-photon level in up to 250 spatio-temporal modes, with an average signal-to-noise ratio of 10(2). We perform a thorough characterization of the whole system, including its multiplexing and demultiplexing stage. We verify that the memory array exhibits low cross-talk even at the single-photon level. The measured performance indicates readiness for storing non-classical states and promises a speed-up in entanglement distribution rates.