Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Dual Signal Optical Bistability in a Semiconductor Optical Amplifier

Aiswarya Kannan

Published Jan 1, 2015• 1 citation
OpenAlex

Abstract

Future all-optical signal processing applications may require the use of multiple optical signals passing through a single, optically bistable device. My thesis investigates an improved model for modeling two optical signals passing through an optically bistable Fabry-Perot semiconductor optical amplifier (FP-SOA). The optical power and phase of these signals are both modeled, as well as the optical gain of the FP-SOA. My improved model is based on an improved model used to study optical bistability of just a single optical signal, in which the internal power is related to the output power with an expression accounting for the Fabry-Perot structure. Work has been performed to put all models into a consistent notation. The resulting, improved model for dual-signal operation indicates lower critical powers to trigger bistable action.

Related papers

An analytical study on bistability of Fabry-Perot semiconductor optical amplifiers

Gang Wang, Shuqiang Chen, Huajun Yang

Abstract Optical bistabilities have been considered to be useful for sensor applications. As a typical nonlinear device, Fabry-Perot semiconductor optical amplifiers (FPSOAs) exhibit bistability under certain conditions. In this paper, the bistable characteristics in FPSOAs are investigated theoretically. Based on Adams’s relationship between the incident optical intensity I in and the z -independent average intracavity intensity I av , an analytical expression of the bistable loop width in SOAs is derived. Numerical simulations confirm the accuracy of the analytical result.

Photonic Sensors•Jun 15, 2016•1 citation

Optical bistability using a Fabry–Perot semiconductor-laser amplifier with two holding beams

Hitoshi Kawaguchi, Kyo Inoue, Hiroyuki Tani

Bistable switching of an optical signal beam by a control beam with a different wavelength, using the nonlinearity of a Fabry-Perot semiconductor-laser amplifier, is reported for the first time to the authors' knowledge. Depending on the initial detuning of the optical signal beam, both normal (counterclockwise) and reverse (clockwise) hysteresis are theoretically and experimentally obtained in the signal output power as a function of the control input power.

Optics Letters•Jul 1, 1987•32 citations

All-optical flip-flop operation in an optical bistable device using two lights of different frequencies

Kyo Inoue

All-optical flip-flop operation in a Fabry-Perot-type optical bistable device (OBD) is investigated. The OBD is switched both from OFF to ON and ON to OFF using two lights of different frequencies as trigger pulses. We present the theoretical calculation, obtained by applying a conventional expression for a dispersive OBD to the two-light input case, and the experimental observation, in which a semiconductor laser amplifier is used as a bistable device.

Optics Letters•Nov 1, 1987•27 citations

Static and Dynamic Optical Bistability in Fabry-Pérot and Distributed Feedback Resonators with Quantum Well structures

F. Castelli, L. A. Lugiato, Gian Paolo Bava +1 more

Recently relevant results on optical bistability in Multiple Quantum Well (MQW) structures at room temperature have been reported [1]. In this paper a rather complete model for optical bistability in Fabry-Pérot (FP) and Distributed Feedback devices (DFB) including a MQW structure is described. It includes the optical dielectric response of the MQW structure, the static output power vs. input power and finally the dynamical behaviour.

Nonlinear Dynamics in Optical Systems•Jan 1, 1992•0 citations

Reconfigurable all-optical bistability/tristability in dual injection-locked Fabry–Perot laser diodes

Mladen Ž. Banović, Petar A. Atanasijević, Marko M. Krstić +4 more

In this Letter, we present a detailed theoretical and experimental investigation of optical bistability and tristability in dual injection-locked Fabry-Perot laser diodes. The proposed device can be reconfigured between the bistable and tristable regimes, simply by adjusting the power level of the injected control optical signal. The tristability presented in the experiment is achieved for relatively low optical input powers between 1.03 and 1.25 mW, with the output signal ratio of up to 7 dB between stable states. Such a device is a potential candidate for designing trits, a bit analogy in ternary computational logic.

Optics Letters•Jul 17, 2023•5 citations

A New Time-Dependant Numerical Model of a Semiconductor Laser Amplifier with Absorbing Regions

Robert Noyes, Jayanta Sarma, I. Middlemast

Two segment devices for optical bistability have been studied extensively but in almost all these cases the switching process is essentially absorption dominated e.g. [1]. In contrast, a particularly interesting new mode of operation from the same device results if a coherent optical signal, placed fairly near to a Fabry-Perot (F-P) resonance of the device, is injected at the initially un-pumped end of the structure. As the intensity of the input signal is increased the unpumped region changes towards transparency thus causing the F-P resonance to ‘sharpen up’ and move with respect to the input signal wavelength. Under suitable conditions highly non-linear amplification of the signal (switching) occurs which can produce at the output a very much altered signal shape than at the input. In this mode of operation the device has potential application as signal pulse re-generators in coherent optical communication systems.

Optical Amplifiers and Their Applications•Jan 1, 1992•0 citations
Future all-optical signal processing applications may require the use of multiple optical signals passing through a single, optically bistable device. My thesis investigates an improved model for modeling two optical signals passing through an optically bistable Fabry-Perot semiconductor optical amplifier (FP-SOA). The optical power and phase of these signals are both modeled, as well as the optical gain of the FP-SOA. My improved model is based on an improved model used to study optical bistability of just a single optical signal, in which the internal power is related to the output power with an expression accounting for the Fabry-Perot structure. Work has been performed to put all models into a consistent notation. The resulting, improved model for dual-signal operation indicates lower critical powers to trigger bistable action.
Abstract Optical bistabilities have been considered to be useful for sensor applications. As a typical nonlinear device, Fabry-Perot semiconductor optical amplifiers (FPSOAs) exhibit bistability under certain conditions. In this paper, the bistable characteristics in FPSOAs are investigated theoretically. Based on Adams’s relationship between the incident optical intensity I in and the z -independent average intracavity intensity I av , an analytical expression of the bistable loop width in SOAs is derived. Numerical simulations confirm the accuracy of the analytical result.
In this Letter, we present a detailed theoretical and experimental investigation of optical bistability and tristability in dual injection-locked Fabry-Perot laser diodes. The proposed device can be reconfigured between the bistable and tristable regimes, simply by adjusting the power level of the injected control optical signal. The tristability presented in the experiment is achieved for relatively low optical input powers between 1.03 and 1.25 mW, with the output signal ratio of up to 7 dB between stable states. Such a device is a potential candidate for designing trits, a bit analogy in ternary computational logic.
Two segment devices for optical bistability have been studied extensively but in almost all these cases the switching process is essentially absorption dominated e.g. [1]. In contrast, a particularly interesting new mode of operation from the same device results if a coherent optical signal, placed fairly near to a Fabry-Perot (F-P) resonance of the device, is injected at the initially un-pumped end of the structure. As the intensity of the input signal is increased the unpumped region changes towards transparency thus causing the F-P resonance to ‘sharpen up’ and move with respect to the input signal wavelength. Under suitable conditions highly non-linear amplification of the signal (switching) occurs which can produce at the output a very much altered signal shape than at the input. In this mode of operation the device has potential application as signal pulse re-generators in coherent optical communication systems.