Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEICE Transactions on Fundamentals of Electronics Communications and Computer Sciences

All-NbN edge junction nanobridges as Josephson mixers

Tsuyoshi Yakihara, Katsuyoshi Hamasaki, Tsutomu Yamashita, Toshiaki Matsui, Risao Hayashi

Published Apr 25, 1986• 1 citation
OpenAlex

Related papers

NbN Tunnel Junctions with AL Striplines and NbN Transition-Edge Bolometers for Terahertz Mixers

Matthias Schicke, Thomas Lehnert, K. H. Gundlach +4 more

•Aug 1, 1997•1 citation

NbN/AIN/NbN Tunnel Junctions Applied as Terahertz SIS Mixers

Zhen Wang, Yoshinori Uzawa, Akira Kawakami

IEICE Transactions on Electronics•Oct 25, 1997•3 citations

Design of a Waveguide SIS Mixer Using Epitaxial NbN/AlN/NbN Tunnel Junctions

Masanori Takeda, Yoshinori Uzawa, Akira Kawakami +1 more

•Jan 1, 2003•0 citations

NBN BASED JOSEPHSON JUNCTIONS

Alexandre Shoji

De Gruyter eBooks•Dec 31, 1986•5 citations

All-NbN nanobridges as Josephson mixers

Toshiaki Matsui, Z. Wang, K. Hamasaki +2 more

Using RIE (reactive in etching) and lift-off techniques, all-NbN nanobridges with gap structure in the I-V (current-voltage) curves have been reproducibly constructed for testing as millimeter-wave mixers. The nanobridges were constructed on NbN/MgO/NbN edge junctions. They were characterized by measurements of their I-V curve and dI/dV versus V and by mixing experiments at 105.9 GHz. These devices had high normal-state resistance, and showed almost ideal Josephson response to external magnetic flux and to millimeter-wave irradiation. The I-V curve remained nonhysteretic from T/sub c/ to 4.2 K, and millimeter-wave-induced steps in the I-V curve were observed up to approximately 3 mV. The cooling of the NbN nanobridges was quite good due to their small size and VTB geometry and the high thermal conductivity of the MgO films. Hence the Josephson response of these devices to millimeter waves was comparatively less limited by self-heating.>

IEEE Transactions on Magnetics•Mar 1, 1989•5 citations

High‐frequency properties of nbn(g)/al nanobridge‐type josephson mixers

Zhen Wang, Akira Kawakami, Bokuji Komiyama +2 more

Abstract To reduce the self‐heating effect and thermal noise in bridge‐type Josephson mixers, all‐NbN nanobridges with an Al “direct shunt” resistor were fabricated. This paper describes the millimeter‐wave response and mixing properties of the NbN(g)/Al nanobridge‐type Josephson mixers in the 100‐GHz frequency. The effective noise temperature TNeff of the nanobridges was decreased to the bath temperature (liquid helium temperature, 4.2 K) by the Al “direct shunt” resistor and the millimeter‐wave induced steps were clearly observed at higher voltage (∼4 mV) than in the nanobridge without the Al “direct shunt” resistor. The millimeter‐wave current dependence of the height of the millimeter‐wave induced steps was analyzed quantitatively, taking into account the thermal noise in the RSCJ model. The simulated result agreed with the experimental result very well. The systematic decrease of the induced step height with an increase of millimeter‐wave current was explained as the increase of effective noise temperature due to absorption of millimeter‐wave power. In the 100‐GHz Josephson mixing experiment, a large IF power output was obtained at a voltage up to about 1.6 mV. The effective noise power NEP and conversion efficiency were about 3 × 10−20 W/Hz and 0.2, respectively.

Electronics and Communications in Japan (Part II Electronics)•Jan 1, 1993•0 citations
Using RIE (reactive in etching) and lift-off techniques, all-NbN nanobridges with gap structure in the I-V (current-voltage) curves have been reproducibly constructed for testing as millimeter-wave mixers. The nanobridges were constructed on NbN/MgO/NbN edge junctions. They were characterized by measurements of their I-V curve and dI/dV versus V and by mixing experiments at 105.9 GHz. These devices had high normal-state resistance, and showed almost ideal Josephson response to external magnetic flux and to millimeter-wave irradiation. The I-V curve remained nonhysteretic from T/sub c/ to 4.2 K, and millimeter-wave-induced steps in the I-V curve were observed up to approximately 3 mV. The cooling of the NbN nanobridges was quite good due to their small size and VTB geometry and the high thermal conductivity of the MgO films. Hence the Josephson response of these devices to millimeter waves was comparatively less limited by self-heating.>
Abstract To reduce the self‐heating effect and thermal noise in bridge‐type Josephson mixers, all‐NbN nanobridges with an Al “direct shunt” resistor were fabricated. This paper describes the millimeter‐wave response and mixing properties of the NbN(g)/Al nanobridge‐type Josephson mixers in the 100‐GHz frequency. The effective noise temperature TNeff of the nanobridges was decreased to the bath temperature (liquid helium temperature, 4.2 K) by the Al “direct shunt” resistor and the millimeter‐wave induced steps were clearly observed at higher voltage (∼4 mV) than in the nanobridge without the Al “direct shunt” resistor. The millimeter‐wave current dependence of the height of the millimeter‐wave induced steps was analyzed quantitatively, taking into account the thermal noise in the RSCJ model. The simulated result agreed with the experimental result very well. The systematic decrease of the induced step height with an increase of millimeter‐wave current was explained as the increase of effective noise temperature due to absorption of millimeter‐wave power. In the 100‐GHz Josephson mixing experiment, a large IF power output was obtained at a voltage up to about 1.6 mV. The effective noise power NEP and conversion efficiency were about 3 × 10−20 W/Hz and 0.2, respectively.