Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE International Symposium on Circuits and Systems proceedings

A COMPACT FREQUENCY COMB GENERATOR FOR LARGE-FORMAT SUPERCONDUCTING MICROWAVE KINETIC INDUCTANCE DETECTORS

Sungyoun Seo, Frank Danso, Chang Sub Kim, Sungho Kim

Published Jan 1, 2025• 1 citation
Publisher

Abstract

MKIDs are sensitive superconducting detectors that shift the phase of resonant frequencies in response to photon strikes. A large-format array with several hundreds of thousands of resonators is required for large-scale submillimeter wave observations in space, but it encounters multiple challenges, the biggest of which is the absence of compact, energy-efficient, and radiation-tolerant readout solutions. Of multiple functions in the MKID readout, the new frequency comb generator is presented in this paper, featuring the low on-chip memory requirement while promising the relaxed frequency resolution in the readout, and enabling the ASIC implementation of a compact, energy-efficient frequency comb generation solution for large-format MKIDs. The proposed comb generator achieved a 128 times reduction in the on-chip memory requirement and 80 times tone information compression. The proposed comb generation method was verified through simulation using MATLAB/Simulink.

DOI
10.23860/thesis-2593

Related papers

HARDWARE IMPLEMENTATION OF AN EFFICIENT FREQUENCY COMB GENERATOR FOR MICROWAVE KINETIC INDUCTANCE DETECTORS

Frank Danso

The frequency comb generator is an essential component in the readout of superconducting detectors. This component is responsible for generating the resonant frequencies necessary to detect photon interaction with the detectors. This component however has not received the much needed attention in terms of readout systems optimization. Conventional implementations rely on either inverse fast Fourier transform (IFFT) engines, which scale poorly in power with increasing frequency resolution requirement but allow flexible tone updates, or lookup tables (LUTs), which demand large memory for high frequency resolution. Microwave Kinetic Inductance Detectors (MKIDs) are superconducting detectors which have gained significant interest for cryogenic astrophysical instrumentation due to their high sensitivity, intrinsic multiplexing capability, and scalable fabrication. However, their simplified detector architecture shifts complexity to the readout electronics, making the development of compact, low-power frequency comb generators especially valuable. The design of the compact frequency comb generator targets applications involving MKIDs which typically detect photons in the submilliter bands. In this thesis, I present the design and hardware realization of a compact frequency comb generator. The design has been verified on an Field Programmable Gate Array (FPGA) using the Xilinx's RFSoC ZCU111 evaluation board. The architecture consumes less than 5% of FPGA resources and less than 5 Watts of power with the capability of handling multiple independent channels of the compact frequency comb generator on the evaluation board. These results demonstrate the potential of this approach to enable scalable, energy-efficient MKID readout systems for large-format detector arrays in next-generation cryogenic experiments.

•Jan 1, 2025•0 citations

Design and Readout of Large MKID Arrays for Submillimeter Astronomy

James A. Schlaerth, Omid Noroozian, Nicole G. Czakon +16 more

Microwave Kinetic Inductance Detectors (MKIDs) are superconducting microresonators useful as detectors for sub/millimeter and far-infrared cameras, as well as instruments in optical and x-ray wavelengths. A probe sine wave at the resonance frequency can detect a change in frequency and microwave loss due to submillimeter optical load as a phase or amplitude change. These detectors may be coupled to light through on-chip, phased-array antennas. A single antenna may feed several detectors with different bandpasses defined by on-chip lumped-element filters. The resonators are easily frequency multiplexed by tuning the resonance frequencies, so hundreds of detectors can be read out while coupled to a single feedline. The deployment and operation of ground-based, background-limited detectors in close-packed arrays present significant challenges in both readout strategy and array design. The initial designs consisted of simple coplanar waveguide microwave resonators with aluminum absorptive sections. The first change has been to substitute the capacitive portion of the resonator with a large interdigitated capacitor (IDC) to reduce its noise contribution. While their low-noise characteristics have been demonstrated, these detectors had not yet been tested on array-scale devices. We present results from arrays of detectors designed for sub/millimeter imaging, tested for their optical response characteristics. In particular, we address challenges of microwave inter-resonator coupling, out-of-band resonator optical sensitivity, and noise reduction in the latest device designs. We show the results of stepped-impedance filters in preventing direct pickup of wide-band radiation, and new frequency spacing to limit crosstalk between resonators. We show direct comparison between olderdesign coplanar waveguide resonators and new IDC resonators under optical load, demonstrating the noise reduction and comparable responsivity. In addition, we show results of the probe signal readout power that maximizes signal-to-noise.

Softwaretechnik-Trends•Mar 1, 2010•0 citations

Towards a Low-Cost Readout System for Arrays of Cryogenic Detectors

K. J. Ramos, Horacio Arnaldi, L. Tosi

A microwave kinetic inductance detector (MKID) is a superconducting pair-breaking detector used for astronomical observations in the sub-millimeter through visible range. Radiation is detected as a phase and amplitude signal proportional to the frequency shift of the device. In the case of arrays of MKIDs, the read-out is performed using the frequency division multiplexing technique. However, there is currently no commercial system or low-cost standard electronics available for this task. In this work, we take the first steps towards developing a low-cost readout system for MKIDs based on the Red Pitaya board. We have developed a firmware for the efficient generation of probe tones, and show figures of merit characterizing the performance of the readout in a hardware prototype. The design is flexible, letting us to adapt it to new frequencies and amplitudes requirements of the MKID arrays.

Argentine Conference on Electronics (CAE)•Mar 9, 2023•2 citations

Superconducting Microwave Resonator Arrays for Submillimeter/Far-infrared Imaging

Omid Noroozian

Superconducting microwave resonators have the potential to revolutionize submillimeter and far-infrared astronomy, and with it our understanding of the universe. The field of low-temperature detector technology has reached a point where extremely sensitive devices like transition-edge sensors are now capable of detecting radiation limited by the background noise of the universe. However, the size of these detector arrays are limited to only a few thousand pixels. This is because of the cost and complexity of fabricating large-scale arrays of these detectors that can reach up to 10 lithographic levels on chip, and the complicated SQUID-based multiplexing circuitry and wiring for readout of each detector. In order to make substantial progress, next- generation ground-based telescopes such as CCAT or future space telescopes require focal planes with large-scale detector arrays of 104–106 pixels. Arrays using microwave kinetic inductance detectors (MKID) are a potential solution. These arrays can be easily made with a single layer of superconducting metal film deposited on a silicon substrate and pattered using conventional optical lithography. Furthermore, MKIDs are inherently multiplexable in the frequency domain, allowing ∼ 103 detectors to be read out using a single coaxial transmission line and cryogenic amplifier, drastically reducing cost and complexity. An MKID uses the change in the microwave surface impedance of a superconducting thin-film microresonator to detect photons. Absorption of photons in the superconductor breaks Cooper pairs into quasiparticles, changing the complex surface impedance, which results in a perturbation of resonator frequency and quality factor. For excitation and readout, the resonator is weakly coupled to a transmission line. The complex amplitude of a microwave probe signal tuned on-resonance and transmitted on the feedline past the resonator is perturbed as photons are absorbed in the superconductor. The perturbation can be detected using a cryogenic amplifier and subsequent homodyne mixing at room temperature. In an array of MKIDs, all the resonators are coupled to a shared feedline and are tuned to slightly different frequencies. They can be read out simultaneously using a comb of frequencies generated and measured using digital techniques. This thesis documents an effort to demonstrate the basic operation of ∼ 256 pixel arrays of lumped-element MKIDs made from superconducting TiNx on silicon. The resonators are designed and simulated for optimum operation. Various properties of the resonators and arrays are measured and compared to theoretical expectations. A particularly exciting observation is the extremely high quality factors (∼ 3 × 107) of our TiNx resonators which is essential for ultra-high sensitivity. The arrays are tightly packed both in space and in frequency which is desirable for larger full-size arrays. However, this can cause a serious problem in terms of microwave crosstalk between neighboring pixels. We show that by properly designing the resonator geometry, crosstalk can be eliminated; this is supported by our measurement results. We also tackle the problem of excess frequency noise in MKIDs. Intrinsic noise in the form of an excess resonance frequency jitter exists in planar superconducting resonators that are made on dielectric substrates. We conclusively show that this noise is due to fluctuations of the resonator capacitance. In turn, the capacitance fluctuations are thought to be driven by two-level system (TLS) fluctuators in a thin layer on the surface of the device. With a modified resonator design we demonstrate with measurements that this noise can be substantially reduced. An optimized version of this resonator was designed for the multiwavelength submillimeter kinetic inductance camera (MUSIC) instrument for the Caltech Submillimeter Observatory.

•Jun 12, 2012•14 citations

Modeling and Simulation of Microwave Kinetic Inductance Detector Readout System Using Simulink and RF Blockset

Taehoon Kim

Microwave kinetic inductance detectors (MKIDs) represent a class of low-temperature superconducting detectors employed for observing astronomical phenomena spanning the submillimeter through visible bands. Renowned for their intrinsic frequency-division multiplexing capability at microwave frequencies, MKIDs offer the advantage of eliminating the need for complex cryogenic multiplexing electronics. However, the overall readout architecture remains complex, necessitating sophisticated room-temperature electronics. Optimizing overall performance poses a significant challenge. This article introduces a novel approach to behavioral modeling and simulation for the MKID readout system utilizing Simulink and the RF Blockset library. The models incorporate major nonidealities of electronic components to investigate their impacts on system performance. In addition, the model of the MKID array is included based on measured transmission data, ensuring high simulation accuracy. The simulation tool facilitates the study and high-level design of the MKID readout system before delving into hardware implementation.

IEEE Transactions on Applied Superconductivity•Mar 4, 2025•3 citations

Calibration Scheme for Large Kinetic Inductance Detector Arrays Based on Readout Frequency Response

Laura Bisigello, S. J. C. Yates, Vignesh Murugesan +2 more

Microwave kinetic inductance detector (MKID) provides a way to build large ground-based sub-mm instruments such as NIKA and A-MKID. For such instruments, therefore, it is important to understand and characterize the response to ensure good linearity and calibration over a wide dynamic range. We propose to use the MKID readout frequency response to determine the MKID responsivity to an input optical source power. A signal can be measured in a KID as a change in the phase of the readout signal with respect to the KID resonant circle. Fundamentally, this phase change is due to a shift in the KID resonance frequency, in turn due to a radiation induced change in the quasiparticle number in the superconducting resonator. We show that the shift in resonant frequency can be determined from the phase shift by using KID phase versus frequency dependence using a previously measured resonant frequency. Working in this calculated resonant frequency, we gain near linearity and constant calibration to a constant optical signal applied in a wide range of operating points on the resonance and readout powers. This calibration method has three particular advantages: first, it is fast enough to be used to calibrate large arrays, with pixel counts in the thousands of pixels; second, it is based on data that are already necessary to determine KID positions; third, it can be done without applying any optical source in front of the array.

arXiv:1602.00442•Journal of Low Temperature Physics•Feb 9, 2016•13 citations
MKIDs are sensitive superconducting detectors that shift the phase of resonant frequencies in response to photon strikes. A large-format array with several hundreds of thousands of resonators is required for large-scale submillimeter wave observations in space, but it encounters multiple challenges, the biggest of which is the absence of compact, energy-efficient, and radiation-tolerant readout solutions. Of multiple functions in the MKID readout, the new frequency comb generator is presented in this paper, featuring the low on-chip memory requirement while promising the relaxed frequency resolution in the readout, and enabling the ASIC implementation of a compact, energy-efficient frequency comb generation solution for large-format MKIDs. The proposed comb generator achieved a 128 times reduction in the on-chip memory requirement and 80 times tone information compression. The proposed comb generation method was verified through simulation using MATLAB/Simulink.
The frequency comb generator is an essential component in the readout of superconducting detectors. This component is responsible for generating the resonant frequencies necessary to detect photon interaction with the detectors. This component however has not received the much needed attention in terms of readout systems optimization. Conventional implementations rely on either inverse fast Fourier transform (IFFT) engines, which scale poorly in power with increasing frequency resolution requirement but allow flexible tone updates, or lookup tables (LUTs), which demand large memory for high frequency resolution. Microwave Kinetic Inductance Detectors (MKIDs) are superconducting detectors which have gained significant interest for cryogenic astrophysical instrumentation due to their high sensitivity, intrinsic multiplexing capability, and scalable fabrication. However, their simplified detector architecture shifts complexity to the readout electronics, making the development of compact, low-power frequency comb generators especially valuable. The design of the compact frequency comb generator targets applications involving MKIDs which typically detect photons in the submilliter bands. In this thesis, I present the design and hardware realization of a compact frequency comb generator. The design has been verified on an Field Programmable Gate Array (FPGA) using the Xilinx's RFSoC ZCU111 evaluation board. The architecture consumes less than 5% of FPGA resources and less than 5 Watts of power with the capability of handling multiple independent channels of the compact frequency comb generator on the evaluation board. These results demonstrate the potential of this approach to enable scalable, energy-efficient MKID readout systems for large-format detector arrays in next-generation cryogenic experiments.
Microwave Kinetic Inductance Detectors (MKIDs) are superconducting microresonators useful as detectors for sub/millimeter and far-infrared cameras, as well as instruments in optical and x-ray wavelengths. A probe sine wave at the resonance frequency can detect a change in frequency and microwave loss due to submillimeter optical load as a phase or amplitude change. These detectors may be coupled to light through on-chip, phased-array antennas. A single antenna may feed several detectors with different bandpasses defined by on-chip lumped-element filters. The resonators are easily frequency multiplexed by tuning the resonance frequencies, so hundreds of detectors can be read out while coupled to a single feedline. The deployment and operation of ground-based, background-limited detectors in close-packed arrays present significant challenges in both readout strategy and array design. The initial designs consisted of simple coplanar waveguide microwave resonators with aluminum absorptive sections. The first change has been to substitute the capacitive portion of the resonator with a large interdigitated capacitor (IDC) to reduce its noise contribution. While their low-noise characteristics have been demonstrated, these detectors had not yet been tested on array-scale devices. We present results from arrays of detectors designed for sub/millimeter imaging, tested for their optical response characteristics. In particular, we address challenges of microwave inter-resonator coupling, out-of-band resonator optical sensitivity, and noise reduction in the latest device designs. We show the results of stepped-impedance filters in preventing direct pickup of wide-band radiation, and new frequency spacing to limit crosstalk between resonators. We show direct comparison between olderdesign coplanar waveguide resonators and new IDC resonators under optical load, demonstrating the noise reduction and comparable responsivity. In addition, we show results of the probe signal readout power that maximizes signal-to-noise.
A microwave kinetic inductance detector (MKID) is a superconducting pair-breaking detector used for astronomical observations in the sub-millimeter through visible range. Radiation is detected as a phase and amplitude signal proportional to the frequency shift of the device. In the case of arrays of MKIDs, the read-out is performed using the frequency division multiplexing technique. However, there is currently no commercial system or low-cost standard electronics available for this task. In this work, we take the first steps towards developing a low-cost readout system for MKIDs based on the Red Pitaya board. We have developed a firmware for the efficient generation of probe tones, and show figures of merit characterizing the performance of the readout in a hardware prototype. The design is flexible, letting us to adapt it to new frequencies and amplitudes requirements of the MKID arrays.
Superconducting microwave resonators have the potential to revolutionize submillimeter and far-infrared astronomy, and with it our understanding of the universe. The field of low-temperature detector technology has reached a point where extremely sensitive devices like transition-edge sensors are now capable of detecting radiation limited by the background noise of the universe. However, the size of these detector arrays are limited to only a few thousand pixels. This is because of the cost and complexity of fabricating large-scale arrays of these detectors that can reach up to 10 lithographic levels on chip, and the complicated SQUID-based multiplexing circuitry and wiring for readout of each detector. In order to make substantial progress, next- generation ground-based telescopes such as CCAT or future space telescopes require focal planes with large-scale detector arrays of 104–106 pixels. Arrays using microwave kinetic inductance detectors (MKID) are a potential solution. These arrays can be easily made with a single layer of superconducting metal film deposited on a silicon substrate and pattered using conventional optical lithography. Furthermore, MKIDs are inherently multiplexable in the frequency domain, allowing ∼ 103 detectors to be read out using a single coaxial transmission line and cryogenic amplifier, drastically reducing cost and complexity. An MKID uses the change in the microwave surface impedance of a superconducting thin-film microresonator to detect photons. Absorption of photons in the superconductor breaks Cooper pairs into quasiparticles, changing the complex surface impedance, which results in a perturbation of resonator frequency and quality factor. For excitation and readout, the resonator is weakly coupled to a transmission line. The complex amplitude of a microwave probe signal tuned on-resonance and transmitted on the feedline past the resonator is perturbed as photons are absorbed in the superconductor. The perturbation can be detected using a cryogenic amplifier and subsequent homodyne mixing at room temperature. In an array of MKIDs, all the resonators are coupled to a shared feedline and are tuned to slightly different frequencies. They can be read out simultaneously using a comb of frequencies generated and measured using digital techniques. This thesis documents an effort to demonstrate the basic operation of ∼ 256 pixel arrays of lumped-element MKIDs made from superconducting TiNx on silicon. The resonators are designed and simulated for optimum operation. Various properties of the resonators and arrays are measured and compared to theoretical expectations. A particularly exciting observation is the extremely high quality factors (∼ 3 × 107) of our TiNx resonators which is essential for ultra-high sensitivity. The arrays are tightly packed both in space and in frequency which is desirable for larger full-size arrays. However, this can cause a serious problem in terms of microwave crosstalk between neighboring pixels. We show that by properly designing the resonator geometry, crosstalk can be eliminated; this is supported by our measurement results. We also tackle the problem of excess frequency noise in MKIDs. Intrinsic noise in the form of an excess resonance frequency jitter exists in planar superconducting resonators that are made on dielectric substrates. We conclusively show that this noise is due to fluctuations of the resonator capacitance. In turn, the capacitance fluctuations are thought to be driven by two-level system (TLS) fluctuators in a thin layer on the surface of the device. With a modified resonator design we demonstrate with measurements that this noise can be substantially reduced. An optimized version of this resonator was designed for the multiwavelength submillimeter kinetic inductance camera (MUSIC) instrument for the Caltech Submillimeter Observatory.
Microwave kinetic inductance detectors (MKIDs) represent a class of low-temperature superconducting detectors employed for observing astronomical phenomena spanning the submillimeter through visible bands. Renowned for their intrinsic frequency-division multiplexing capability at microwave frequencies, MKIDs offer the advantage of eliminating the need for complex cryogenic multiplexing electronics. However, the overall readout architecture remains complex, necessitating sophisticated room-temperature electronics. Optimizing overall performance poses a significant challenge. This article introduces a novel approach to behavioral modeling and simulation for the MKID readout system utilizing Simulink and the RF Blockset library. The models incorporate major nonidealities of electronic components to investigate their impacts on system performance. In addition, the model of the MKID array is included based on measured transmission data, ensuring high simulation accuracy. The simulation tool facilitates the study and high-level design of the MKID readout system before delving into hardware implementation.
Microwave kinetic inductance detector (MKID) provides a way to build large ground-based sub-mm instruments such as NIKA and A-MKID. For such instruments, therefore, it is important to understand and characterize the response to ensure good linearity and calibration over a wide dynamic range. We propose to use the MKID readout frequency response to determine the MKID responsivity to an input optical source power. A signal can be measured in a KID as a change in the phase of the readout signal with respect to the KID resonant circle. Fundamentally, this phase change is due to a shift in the KID resonance frequency, in turn due to a radiation induced change in the quasiparticle number in the superconducting resonator. We show that the shift in resonant frequency can be determined from the phase shift by using KID phase versus frequency dependence using a previously measured resonant frequency. Working in this calculated resonant frequency, we gain near linearity and constant calibration to a constant optical signal applied in a wide range of operating points on the resonance and readout powers. This calibration method has three particular advantages: first, it is fast enough to be used to calibrate large arrays, with pixel counts in the thousands of pixels; second, it is based on data that are already necessary to determine KID positions; third, it can be done without applying any optical source in front of the array.