Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Advanced Quantum Technologies

Heteroepitaxial (111) Diamond Quantum Sensors with Preferentially Aligned Nitrogen‐Vacancy Centers for an Electric Vehicle Battery Monitor

Kenichi Kajiyama, Moriyoshi Haruyama, Yuji Hatano, Hiromitsu Kato, Masahiko Ogura, Toshiharu Makino, Hitoshi Noguchi, T. Sekiguchi, Takayuki Iwasaki, Mutsuko Hatano

Published Jan 18, 2025• 17 citations
Publisher

Abstract

Abstract A platform for heteroepitaxial (111) chemical vapor deposition (CVD) diamond quantum sensors with preferentially aligned nitrogen vacancy (NV) centers on a large substrate is developed, and its operation as an electric vehicle (EV) battery monitor is demonstrated. A self‐standing heteroepitaxial CVD diamond film with a (111) orientation and a thickness of 150 µm is grown on a non‐diamond substrate and subsequently separated from it. The high uniformity and crystallinity of the (111)‐oriented diamond is confirmed. A 150‐µm thick NV‐diamond layer is then deposited on the heteroepitaxial diamond. The T 2 value measured by confocal microscopy is 20 µs, which corresponds to substitutional nitrogen defect concentration of 8 ppm. The nitrogen‐vacancy concentration and T 2 * are estimated to be 0.05 ppm and 0.05 µs by continuous wave optically detected magnetic resonance (CW‐ODMR) spectroscopy in a fiber‐top sensor configuration. In a gradiometer, where two sensors are placed on both sides of the busbar, the noise floor is 17 nT/Hz 0.5 in the frequency range of 10–40 Hz without magnetic shielding. The Allan deviation of the magnetic field noise in the laboratory is below 0.3 µT, which corresponds to a busbar current of 10 mA, in the accumulation time range of 10 ms to 100 s.

DOI
10.1002/qute.202400400

Related papers

Current monitoring for electric vehicle batteries using heteroepitaxial CVD diamond quantum sensors

Kenichi Kajiyama, Moriyoshi Haruyama, Yuji Hatano +10 more

Diamond quantum sensors are suited to high-precision measurements of charge/discharge currents for monitoring electric vehicle batteries owing to the wide dynamic range sensing. We have so far demonstrated the current monitoring from 10 mA to 1000 A using nitrogen-vacancy (NV) centers in high-pressure and high-temperature grown diamond substates1. To expand the possibility of realizing the application using diamond quantum sensors, it is preferable to fabricate sensors on heteroepitaxial diamond grown on inexpensive substrates. In this study, we report the current monitoring using heteroepitaxially diamonds grown by chemical vapor deposition (CVD).

•Nov 17, 2023•0 citations

Wide temperature operation of diamond quantum sensor for electric vehicle battery monitoring

Keisuke Kubota, Yuji Hatano, Yuta Kainuma +9 more

Considering the rising popularity of electric vehicles (EVs), it is essential to enhance the cruising mileage and extend the lifetime of batteries. To accomplish this, accurate monitoring of the charge and discharge current of the battery over a wide temperature range is essential. We developed a compact diamond quantum sensor head with a size of 1 × 1 × 0.5 cm3, consisting of a (111) high-pressure and high-temperature synthesized diamond with nitrogen-vacancy centers, by electron beam irradiation, which was adhered to the top of the multimode fiber and surrounded by the microwave antenna, for EV battery monitoring. We demonstrated that our quantum sensor achieved the current measurement accuracy of 10 mA in the −150 to 150 °C temperature range with a bandwidth of 500 Hz under atmospheric pressure and confirmed that the diamond quantum sensor meets the performance requirements of EV current sensors. Moreover, the temperature dependence of shot noise and external magnetic field noise were investigated, and their relation to the linewidth and contrast of the optically detected magnetic resonance spectrum were analyzed. At high temperatures, the contrast decreased because shortening of the singlet lifetime, which accelerate the initialization. At low temperatures, the contrast was slightly decreased. This is possibly a result of increased losses due to condensation on the microwave antenna.

Diamond and Related Materials•Mar 15, 2023•30 citations

Wafer Scale N‐Doped Diamond (111) with Mainly Nitrogen Spin Bath Limited Nitrogen Vacancy Coherence Times from Heteroepitexial Growth

Jürgen Weippert, Jan Engels, Jan Kustermann +9 more

Diamond (111) is grown heteroepitaxially on 2″ Ir/YSZ/Si (111) wafers (YSZ=yttria‐stabilized zirconia) with a diameter of 50 mm and off‐cuts of up to 6, applying plasma‐enhanced chemical vapor deposition supported by bias‐enhanced nucleation and epitaxial lateral overgrowth. In the final growth step, a nitrogen‐doped layer (N‐Cap) is superimposed. In the N‐Cap, a preferential orientation of nitrogen vacancy (NV) centers along the surface normal is observed, which has a T coherence time of 9.3 μs, which is the highest value ever reported for heteroepitaxial diamond (111). In the meantime, the T dephasing time is 95 ns, which means that the T / T ratio is almost 100, while published ratios for homoepitaxial diamond are in the range 5–20. The total nitrogen concentration as measured by Time‐of‐Flight Secondary Ion Mass Spectrometry is determined to be 7.3 ppm, which, in combination with photoluminescence analysis, yields an NV incorporation efficiency of .

physica status solidi (RRL) - Rapid Research Letters•Oct 8, 2025•3 citations

Characterization of low-nitrogen quantum diamond for pulsed magnetometry applications

Jiashen Tang, Connor Roncaioli, Andrew Mark Edmonds +4 more

Ensembles of nitrogen-vacancy (NV) centers in diamond are versatile quantum sensors with broad applications in the physical and life sciences. The concentration of neutral substitutional nitrogen ( [ N s 0 ]) strongly influences NV electronic spin coherence times, sensitivity, and optimal sensing strategies. Diamonds with [ N s 0 ] ∼ 1–10 ppm are a focus of recent material engineering efforts, with higher concentrations being favorable for continuous-wave optically detected magnetic resonance (CW-ODMR) and lower concentrations expected to benefit pulsed magnetometry techniques through extended NV spin coherence times and improved sensing duty cycles. In this work, we synthesize and characterize low- [ N s 0 ] ( ∼ 0.8 ppm), NV-enriched diamond material, engineered through low-strain chemical vapor deposition (CVD) growth on high-quality substrates, 12 C isotopic purification, and controlled electron irradiation and annealing. Our results demonstrate good strain homogeneity in diamonds grown on CVD substrates and spin-bath-limited NV dephasing times. By measuring NV spin and charge properties across a wide range of optical NV excitation intensity, we provide direct comparisons of photon-shot-noise-limited magnetic field sensitivity between the current low- [ N s 0 ] and previously studied higher- [ N s 0 ] ( ∼ 14 ppm) NV-diamond sensors. We show that low- [ N s 0 ] diamond can outperform higher- [ N s 0 ] diamond at moderate and low optical NV excitation intensity. Our results provide practical benchmarks and guidance for selecting NV-diamond sensors tailored to specific experimental constraints and sensing requirements.

arXiv:2509.06884•Frontiers in Quantum Science and Technology•Dec 9, 2025•1 citation

Production of oriented nitrogen-vacancy color centers in synthetic diamond

Andrew Mark Edmonds, Ulrika F. S. D’Haenens-Johansson, Robin J. Cruddace +6 more

The negatively charged nitrogen-vacancy (${\mathrm{NV}}^{\ensuremath{-}}$) center in diamond is an attractive candidate for applications that range from magnetometry to quantum information processing. Here we show that only a fraction of the nitrogen (typically $<0.5$%) incorporated during homoepitaxial diamond growth by chemical vapor deposition (CVD) is in the form of undecorated ${\mathrm{NV}}^{\ensuremath{-}}$ centers. Furthermore, studies on CVD diamond grown on $(110)$-oriented substrates show a near 100% preferential orientation of NV centers along only the $[111]$ and $[\overline{1}\overline{1}1]$ directions, rather than the four possible orientations. The results indicate that NV centers grow in as units, as the diamond is deposited, rather than by migration and association of their components. The NV unit of the ${\mathrm{NVH}}^{\ensuremath{-}}$ is similarly preferentially oriented, but it is not possible to determine whether this defect was formed by H capture at a preferentially aligned NV center or as a complete unit. Reducing the number of NV orientations from four orientations to two orientations should lead to increased optically detected magnetic resonance contrast and thus improved magnetic sensitivity in ensemble-based magnetometry.

arXiv:1112.5757•Physical Review B•Jul 5, 2012•181 citations

Ultrahigh concentration of NV− centers embedded in the CVD epi-diamond layer near the interface with an HPHT diamond substrate

Yuanjie Yang, Shengran Lin, Jiaxin Zhao +4 more

Abstract The negatively charged nitrogen vacancy (NV−) center ensemble in as-grown chemical vapor deposition (CVD) diamond is a promising candidate for quantum sensing due to its long coherence time and excellent optical properties. However, achieving a high concentration of NV− centers in as-grown CVD diamond remains a critical challenge, which constrains the performance of NV− based sensors. In this study, we observe that NV− center formation efficiency is significantly enhanced during the initial growth phase, with a coherence time T 2 * of 1.1 μs. These findings demonstrate that high-concentration NV− centers can be achieved in as-grown diamonds, greatly enhancing their utility in high-performance magnetometers and quantum sensing.

Chinese Physics B•Apr 2, 2025•2 citations
Abstract A platform for heteroepitaxial (111) chemical vapor deposition (CVD) diamond quantum sensors with preferentially aligned nitrogen vacancy (NV) centers on a large substrate is developed, and its operation as an electric vehicle (EV) battery monitor is demonstrated. A self‐standing heteroepitaxial CVD diamond film with a (111) orientation and a thickness of 150 µm is grown on a non‐diamond substrate and subsequently separated from it. The high uniformity and crystallinity of the (111)‐oriented diamond is confirmed. A 150‐µm thick NV‐diamond layer is then deposited on the heteroepitaxial diamond. The T 2 value measured by confocal microscopy is 20 µs, which corresponds to substitutional nitrogen defect concentration of 8 ppm. The nitrogen‐vacancy concentration and T 2 * are estimated to be 0.05 ppm and 0.05 µs by continuous wave optically detected magnetic resonance (CW‐ODMR) spectroscopy in a fiber‐top sensor configuration. In a gradiometer, where two sensors are placed on both sides of the busbar, the noise floor is 17 nT/Hz 0.5 in the frequency range of 10–40 Hz without magnetic shielding. The Allan deviation of the magnetic field noise in the laboratory is below 0.3 µT, which corresponds to a busbar current of 10 mA, in the accumulation time range of 10 ms to 100 s.
Diamond quantum sensors are suited to high-precision measurements of charge/discharge currents for monitoring electric vehicle batteries owing to the wide dynamic range sensing. We have so far demonstrated the current monitoring from 10 mA to 1000 A using nitrogen-vacancy (NV) centers in high-pressure and high-temperature grown diamond substates1. To expand the possibility of realizing the application using diamond quantum sensors, it is preferable to fabricate sensors on heteroepitaxial diamond grown on inexpensive substrates. In this study, we report the current monitoring using heteroepitaxially diamonds grown by chemical vapor deposition (CVD).
Considering the rising popularity of electric vehicles (EVs), it is essential to enhance the cruising mileage and extend the lifetime of batteries. To accomplish this, accurate monitoring of the charge and discharge current of the battery over a wide temperature range is essential. We developed a compact diamond quantum sensor head with a size of 1 × 1 × 0.5 cm3, consisting of a (111) high-pressure and high-temperature synthesized diamond with nitrogen-vacancy centers, by electron beam irradiation, which was adhered to the top of the multimode fiber and surrounded by the microwave antenna, for EV battery monitoring. We demonstrated that our quantum sensor achieved the current measurement accuracy of 10 mA in the −150 to 150 °C temperature range with a bandwidth of 500 Hz under atmospheric pressure and confirmed that the diamond quantum sensor meets the performance requirements of EV current sensors. Moreover, the temperature dependence of shot noise and external magnetic field noise were investigated, and their relation to the linewidth and contrast of the optically detected magnetic resonance spectrum were analyzed. At high temperatures, the contrast decreased because shortening of the singlet lifetime, which accelerate the initialization. At low temperatures, the contrast was slightly decreased. This is possibly a result of increased losses due to condensation on the microwave antenna.
Diamond (111) is grown heteroepitaxially on 2″ Ir/YSZ/Si (111) wafers (YSZ=yttria‐stabilized zirconia) with a diameter of 50 mm and off‐cuts of up to 6, applying plasma‐enhanced chemical vapor deposition supported by bias‐enhanced nucleation and epitaxial lateral overgrowth. In the final growth step, a nitrogen‐doped layer (N‐Cap) is superimposed. In the N‐Cap, a preferential orientation of nitrogen vacancy (NV) centers along the surface normal is observed, which has a T coherence time of 9.3 μs, which is the highest value ever reported for heteroepitaxial diamond (111). In the meantime, the T dephasing time is 95 ns, which means that the T / T ratio is almost 100, while published ratios for homoepitaxial diamond are in the range 5–20. The total nitrogen concentration as measured by Time‐of‐Flight Secondary Ion Mass Spectrometry is determined to be 7.3 ppm, which, in combination with photoluminescence analysis, yields an NV incorporation efficiency of .
Ensembles of nitrogen-vacancy (NV) centers in diamond are versatile quantum sensors with broad applications in the physical and life sciences. The concentration of neutral substitutional nitrogen ( [ N s 0 ]) strongly influences NV electronic spin coherence times, sensitivity, and optimal sensing strategies. Diamonds with [ N s 0 ] ∼ 1–10 ppm are a focus of recent material engineering efforts, with higher concentrations being favorable for continuous-wave optically detected magnetic resonance (CW-ODMR) and lower concentrations expected to benefit pulsed magnetometry techniques through extended NV spin coherence times and improved sensing duty cycles. In this work, we synthesize and characterize low- [ N s 0 ] ( ∼ 0.8 ppm), NV-enriched diamond material, engineered through low-strain chemical vapor deposition (CVD) growth on high-quality substrates, 12 C isotopic purification, and controlled electron irradiation and annealing. Our results demonstrate good strain homogeneity in diamonds grown on CVD substrates and spin-bath-limited NV dephasing times. By measuring NV spin and charge properties across a wide range of optical NV excitation intensity, we provide direct comparisons of photon-shot-noise-limited magnetic field sensitivity between the current low- [ N s 0 ] and previously studied higher- [ N s 0 ] ( ∼ 14 ppm) NV-diamond sensors. We show that low- [ N s 0 ] diamond can outperform higher- [ N s 0 ] diamond at moderate and low optical NV excitation intensity. Our results provide practical benchmarks and guidance for selecting NV-diamond sensors tailored to specific experimental constraints and sensing requirements.
The negatively charged nitrogen-vacancy (${\mathrm{NV}}^{\ensuremath{-}}$) center in diamond is an attractive candidate for applications that range from magnetometry to quantum information processing. Here we show that only a fraction of the nitrogen (typically <0.5<0.5<0.5%) incorporated during homoepitaxial diamond growth by chemical vapor deposition (CVD) is in the form of undecorated ${\mathrm{NV}}^{\ensuremath{-}}$ centers. Furthermore, studies on CVD diamond grown on (110)(110)(110)-oriented substrates show a near 100% preferential orientation of NV centers along only the [111][111][111] and [1‾1‾1][\overline{1}\overline{1}1][111] directions, rather than the four possible orientations. The results indicate that NV centers grow in as units, as the diamond is deposited, rather than by migration and association of their components. The NV unit of the ${\mathrm{NVH}}^{\ensuremath{-}}$ is similarly preferentially oriented, but it is not possible to determine whether this defect was formed by H capture at a preferentially aligned NV center or as a complete unit. Reducing the number of NV orientations from four orientations to two orientations should lead to increased optically detected magnetic resonance contrast and thus improved magnetic sensitivity in ensemble-based magnetometry.
Abstract The negatively charged nitrogen vacancy (NV−) center ensemble in as-grown chemical vapor deposition (CVD) diamond is a promising candidate for quantum sensing due to its long coherence time and excellent optical properties. However, achieving a high concentration of NV− centers in as-grown CVD diamond remains a critical challenge, which constrains the performance of NV− based sensors. In this study, we observe that NV− center formation efficiency is significantly enhanced during the initial growth phase, with a coherence time T 2 * of 1.1 μs. These findings demonstrate that high-concentration NV− centers can be achieved in as-grown diamonds, greatly enhancing their utility in high-performance magnetometers and quantum sensing.