We investigated the loss mechanisms of superconducting circuits with epitaxially grown NbN(100) on MgO(100) substrates by measuring quarter-wave coplanar waveguide resonators with various strip and slot widths. The power dependence of the internal quality factor and the temperature dependence of the resonance frequency shift were evaluated in a dilution refrigerator. The measurement and analysis of the loss in these resonators indicate that the loss was dominated by a two-level system (TLS) loss and the TLS host materials were primarily distributed at the surface of the substrate.
We investigated the loss mechanisms of superconducting circuits with epitaxially grown NbN(100) on MgO(100) substrates by measuring quarter-wave coplanar waveguide resonators with various strip and slot widths. The power dependence of the internal quality factor and the temperature dependence of the resonance frequency shift were evaluated in a dilution refrigerator. The measurement and analysis of the loss in these resonators indicate that the loss was dominated by a two-level system (TLS) loss and the TLS host materials were primarily distributed at the surface of the substrate.
In current superconducting qubit circuit development, coherence time is limited by low-frequency flux noise introduced from localized two-level systems (TLSs) in the fabricated superconducting circuit, including superconducting materials, the interface between thin films, and the substrate. As a part of the effect to tackle this issue from a substrate standpoint, we succeed in fabricating NbN (200) oriented coplanar waveguide resonator (CPWR) on a thin titanium nitride (TiN) (200) buffered Si (100) substrate. The internal loss is close to 3 × 10-5nearphoton> ~1, improved from ~2 × 10-4in NbN (200) CPWR fabricated on MgO (100). For NbN (200) resonators grown on Si (100), the internal loss shows microwave energy independent. To further clarity if this energy independence is due to the change of substrate material, we also fabricated TiN (200) CPWR on Si (100). In contrast to NbN (200) CPWR, the loss of TiN (200) resonator shows a strong microwave dependent, an indication of TLSs originated from the interface and the surface. We suggest TLSs in NbN (200) CPWR are dominated from different mechanism other than arising from the interface and surface.
The high critical magnetic field and relatively high critical temperature of niobium nitride (NbN) make it a promising material for applications in superconducting quantum technology. However, NbN-based superconducting circuits are sensitive to decoherence sources such as two-level system (TLS) defects. Here, we numerically and experimentally investigate NbN superconducting microwave coplanar waveguide resonator arrays with a 100 nm thickness, capacitively coupled to a common coplanar waveguide on a silicon chip. We observe that the resonators' internal quality factor (Qi) decreases fromQi∼1.07×106in a high power regime toQi∼1.36×105in the single photon regime. Data from this study is consistent with the TLS theory, which describes the TLS interactions in resonator substrates and interfaces. Moreover, we study the temperature (T) dependence ofQiand resonance frequencyfrof coplanar waveguide resonators to characterize the quasiparticle density. We observe that the increase in kinetic inductance at higher temperatures is the main reason for the frequency shift. Finally, we measurefrandQiin response to in-plane magnetic fields (B∣∣). We verify thatQistays well above104up toB∣∣= 240 mT in the photon number<nph>= 1.8 atT= 100 mK. Our results could enable the development of robust microwave superconducting circuits for circuit quantum electrodynamics at high magnetic fields required for hybrid superconducting-semiconducting quantum circuits.
The loss in superconducting microwave resonators at low-photon numbers and low temperatures is not well understood but has implications for achievable coherence times in superconducting qubits. We have fabricated single-layer resonators with a high quality factor by patterning a superconducting aluminum film on a sapphire substrate. Four resonator geometries were studied with resonant frequencies ranging from 5 to 7 GHz: a quasi-lumped element resonator, a coplanar strip waveguide resonator, and two hybrid designs that contain both a coplanar strip and a quasi-lumped element. Transmitted power measurements were taken at 30 mK as a function of frequency and probe power. We find that the resonator loss, expressed as the inverse of the internal quality factor, decreases slowly over four decades of photon number in a manner not merely explained by loss from a conventional uniform spatial distribution of two-level systems in an oxide layer on the superconducting surfaces of the resonator.
High quality factor, i.e. low loss, microwave resonators are important for quantum information storage and addressing. In this work we study the resonance frequency and loss in superconducting coplanar waveguide resonators as a function of power and temperature. We find that there is increased loss at low power and low temperature. The increased loss is attributed to the existence of two-level systems (TLS) at the surfaces, interfaces, and in the bulk of insulators deposited on the structures. We show that both the temperature dependence of the resonant frequency and the power dependence of the loss can be used to find the TLS contribution to the loss. The TLS intrinsic loss tangent derived from the frequency shift data at high power is shown to agree well with the direct loss measurement at low power. The former allows for a relatively fast measurement of the TLS loss. As an example, we measure the properties of amorphous AlOXdeposited on the resonators and find a TLS loss tangent of 1 × 10-3.
Abstract We numerically and experimentally investigate the phononic loss for superconducting resonators fabricated on a piezoelectric substrate. With the help of finite element method simulations, we calculate the energy loss due to electromechanical conversion into bulk and surface acoustic waves. This sets an upper limit for the resonator internal quality factor Q i. To validate the simulation, we fabricate quarter wavelength coplanar waveguide resonators on GaAs and measure Q i as function of frequency, power and temperature. We observe a linear increase of Q i with frequency, as predicted by the simulations for a constant electromechanical coupling. Additionally, Q i shows a weak power dependence and a negligible temperature dependence around 10 mK, excluding two level systems and non-equilibrium quasiparticles as the main source of losses at that temperature.
In this master's thesis, I present the design, fabrication, and characterisation of superconducting microwave resonators. These resonators are quarter-wavelength coplanar waveguide resonators, operating at resonance frequencies between 4 GHz and 8 GHz. This kind of resonator is a key component in several applications, ranging from quantum computation devices to parametric amplifiers. Minimising the losses (achieving high internal quality factors) in these resonators is important to maximise performance of the applications they are used for. During the thesis work, we have studied several possible changes to improve the resonator quality.\n\nFabrication of the resonators was done in the Nanofabrication Laboratory at Chalmers University of Technology, and consist of the following steps: cleaning a sapphire or silicon wafer, depositing a layer of superconducting niobium, photolithography, and etching the waveguide. We then measured the resonators in a cryogen-free dilution refrigerator, at a temperature of 10 mK. The measurements consisted of a power sweep, in order to quantify the quality factor at high and low excitation powers. As an example, the first resonator we fabricated had a quality factor of 4.3 x 10^4 at high power (about 10^5 photons in the resonator), and quality factor of 3.7 x 10^4 at the single-photon level.\n\nWe then investigated different loss mechanisms that we expect to negatively affect the quality factor, and how to reduce this loss. Firstly, to reduce radiation losses and magnetic vortex losses, we reduced the lateral dimensions of the resonator. Secondly, as two-level system (TLS) losses are believed to mainly reside at the surfaces of the materials and interfaces between them, we etched into the substrate to selectively move a part of the TLS away from the resonator. We also studied the effect of the meandering of the resonator on the quality factor, as well as using two different etching gasses.\n\nBy gathering all this data, we were then able to compare the different combinations to see the effect of the changing parameters. In conclusion, the reduced lateral dimensions and the removal of part of the substrate indeed reduce the losses, as expected from the theory. We also found interesting behaviour with regards to the meandering, namely that having a meandered structure negatively affects the quality factor.\n\nCombining all results, we can give a guideline for the fabrication of resonators in the future, which gave us a quality factor up to 4.9 x 10^5 at high excitation power, and 3.0 x 10^5 at the single photon level.