Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Conference on Precision Electromagnetic Measurements

Operation of Josephson Voltage Standard with Superconducting Shield in Magnetic-Field Environment

Daiki Matsumaru, Takehiko Oe, Shuji Nakamura, Michitaka Maruyama, Nobu‐Hisa Kaneko

Published Jul 8, 2024• 1 citation
Publisher

Abstract

We have successfully operated a Josephson voltage standard (JVS) with a superconducting shield in a magnetic-field environment. This study involves mounting a NbN-based JVS chip on a custom-made 12 K stage adjacent to the 4 K stage within a dilution refrigerator. A magnetic field, reaching up to 10 T and generated by a superconducting magnet positioned 73 cm below the JVS chip, is initially reduced by a cancellation coil and further minimized by a superconducting shield comprising Nb, Pb, and permalloy. Consequently, clear Shapiro steps were observed under a magnetic field of approximately 10 T. This achievement marks a significant milestone toward facilitating quantum metrology triangle experiments within a single dilution refrigerator and conducting precise voltage measurements under extreme conditions.

DOI
10.1109/cpem61406.2024.10645975

Related papers

Development of Current Measurement System with Programmable Josephson Voltage Standard and Quantum Hall Resistance Array in a Single Dilution Refrigerator

Daiki Matsumaru, Takehiko Oe, Shuji Nakamura +8 more

We evaluated two types of quantum devices, namely, the programmable Josephson voltage standard and the quantum Hall resistance array, for use in a current measurement system within a single dilution refrigerator. The results showed stable operation for both devices under a magnetic field of 10.2 T, generated by a superconducting magnet. This stability was achieved using a magnetic shielding method with a superconducting magnetic shield structure that we developed. Herein, we describe the current measurement system that allows for flexible measurement configurations. This research not only focuses on current measurement but also lays the groundwork for future studies, including quantum current generation and experiments related to the quantum metrology triangle.

Conference on Precision Electromagnetic Measurements•Sep 1, 2026•0 citations

Feasibility of the Josephson voltage and current standards on a single chip

Rais S. Shaikhaidarov, Ilya Antonov, Kyung Ho Kim +5 more

The quantum Josephson voltage standard is well established across the metrology community for many years. It relies on the synchronization of the flux tunneling in the S/I/S Josephson junctions (JJ) with the microwave radiation (MW) of frequency f such that V=Φ0fm, where m = 0, 1, 2, …. The phenomenon is called the Shapiro steps. Together with the quantum Hall resistance standard, the voltage standard forms the foundation of electrostatic metrology. The current is then defined as the ratio of the voltage and resistance. Realization of the quantum current standard would close the electrostatic metrological triangle of voltage–resistance–current. The current quantization I=2efm, the inverse Shapiro steps, was recently shown using the superconducting nanowires and small JJ. The effect is a synchronization of the MW with the Cooper pair tunneling. This paves the way to combine the JJ voltage and current standards on the same chip and demonstrate feasibility of the multi-standard operation. We show the voltage and current quantization on the same chip up to frequency of 10 GHz, corresponding to the amplitudes ∼ 20.67 μV and ∼ 3.2 nA, respectively. The accuracy of the voltage and current quantization, however, is relatively low, 35 and 100 ppk, respectively. We discuss measures to optimize the JJs, circuit, and environment to boost the amplitude and accuracy of the standards.

arXiv:2410.11018•Applied Physics Letters•Sep 16, 2024•7 citations

Operation of a NbN-based programmable Josephson voltage standard chip with a compact refrigeration system

Alexandre Shoji, Hirotake Yamamori, Mayumi Ishizaki +2 more

A refrigeration system was designed and constructed for realizing a liquid-He-free programmable Josephson voltage standard. The system is equipped with a two-stage Gifford-McMahon cooler, a thermal-radiation shield, a magnetic-field shield and semi-rigid coaxial cables to supply microwave power to a chip. The performance of the system was examined by use of a NbN-based 8-bit digital-to-analog converter (DAC) chip designed as a 1 V programmable voltage standard. When operated at 8.5 K on the cryocooler, constant-voltage steps with amplitudes greater than 1 mA were observed for every segment of junction arrays on the chip.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•37 citations

Demonstration of a 10 V programmable Josephson voltage standard system based on a multi-chip technique

Tatsuji Yamada, Hajime SASAKI, Hirotake Yamamori +1 more

We have demonstrated a programmable Josephson voltage standard (PJVS) operation up to 10.84 V using a multi-chip technique. We combined two PJVS chips fabricated using NbN/(TiN x /NbN) 2 junction technology. Each PJVS chip was mounted on a single chip carrier using bonding wire, and the two chip carriers were connected by a simple Cu lead wire, and mounted on a cryocooler. High-precision measurements confirmed flat voltage steps for all 22 cells, with a peak-to-peak variation of 100 nV and wide margins of at least 0.35 mA. We also confirmed the stability of the voltage steps in spite of a temperature and RF frequency variation of ± 0.1 K and ± 0.1 GHz, respectively.

Superconductor Science and Technology•Feb 1, 2008•14 citations

Cryogen-free operation of programmable Josephson voltage standard with a closed-cycle refrigerator

Yonuk Chong, Mun-Seog Kim, Wan-Seop Kim +1 more

We report operation of a programmable Josephson voltage standard on a closed-cycle refrigerator. NIST 1V PJVS chip is used, and we operate the chip with the fingerboard that is adopted from the existing liquid helium dipping probe. We demonstrate operation at 5.5 K of chip temperature, with a flat Shapiro step in the sub-array of the chip.

Conference on Precision Electromagnetic Measurements•Jun 1, 2008•0 citations

Josephson voltage standard circuit operation with a pulse tube cooler

G. Wende, M. Schubert, T. May +9 more

For a more wide-spread use of Josephson voltage standards, cryogen-free operation, by means of an appropriate closed-cycle refrigerator, is highly desirable. In this work we present a low-noise pulse tube cooler (PTC) that is capable to cool the voltage standard circuits to temperatures below 4 K. As a low loss dielectric waveguide with a very small thermal conductivity a Teflon strip was used for the microwave transmission. The matched transition from the WR12 rectangular waveguide to the Teflon strip and vice versa was made using special exponential tapers. Programmable 1 Volt 14 bit SINIS and 10 Volt SIS arrays assembled in the PTC operated well, i.e., demonstrated a similar performance to that measured in liquid helium. The Josephson junction arrays were integrated in coplanar strips instead of the commonly used microstriplines for the microwave transmission lines. The 1 Volt SINIS array contained 8192 Josephson junctions (JJs). It generated an inherently stable Josephson voltage step of 1.19 V at a driving microwave frequency of 70 GHz. The step width was 150 /spl mu/A and the critical current of the junctions was 550 /spl mu/A. Similar results were obtained under liquid helium cooling conditions. In another experiment a 10 Volt voltage standard chip with 19700 SIS JJs was installed. It was possible to generate stable Shapiro steps at the 10 V level.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•19 citations
We have successfully operated a Josephson voltage standard (JVS) with a superconducting shield in a magnetic-field environment. This study involves mounting a NbN-based JVS chip on a custom-made 12 K stage adjacent to the 4 K stage within a dilution refrigerator. A magnetic field, reaching up to 10 T and generated by a superconducting magnet positioned 73 cm below the JVS chip, is initially reduced by a cancellation coil and further minimized by a superconducting shield comprising Nb, Pb, and permalloy. Consequently, clear Shapiro steps were observed under a magnetic field of approximately 10 T. This achievement marks a significant milestone toward facilitating quantum metrology triangle experiments within a single dilution refrigerator and conducting precise voltage measurements under extreme conditions.
We evaluated two types of quantum devices, namely, the programmable Josephson voltage standard and the quantum Hall resistance array, for use in a current measurement system within a single dilution refrigerator. The results showed stable operation for both devices under a magnetic field of 10.2 T, generated by a superconducting magnet. This stability was achieved using a magnetic shielding method with a superconducting magnetic shield structure that we developed. Herein, we describe the current measurement system that allows for flexible measurement configurations. This research not only focuses on current measurement but also lays the groundwork for future studies, including quantum current generation and experiments related to the quantum metrology triangle.
The quantum Josephson voltage standard is well established across the metrology community for many years. It relies on the synchronization of the flux tunneling in the S/I/S Josephson junctions (JJ) with the microwave radiation (MW) of frequency f such that V=Φ0fm, where m = 0, 1, 2, …. The phenomenon is called the Shapiro steps. Together with the quantum Hall resistance standard, the voltage standard forms the foundation of electrostatic metrology. The current is then defined as the ratio of the voltage and resistance. Realization of the quantum current standard would close the electrostatic metrological triangle of voltage–resistance–current. The current quantization I=2efm, the inverse Shapiro steps, was recently shown using the superconducting nanowires and small JJ. The effect is a synchronization of the MW with the Cooper pair tunneling. This paves the way to combine the JJ voltage and current standards on the same chip and demonstrate feasibility of the multi-standard operation. We show the voltage and current quantization on the same chip up to frequency of 10 GHz, corresponding to the amplitudes ∼ 20.67 μV and ∼ 3.2 nA, respectively. The accuracy of the voltage and current quantization, however, is relatively low, 35 and 100 ppk, respectively. We discuss measures to optimize the JJs, circuit, and environment to boost the amplitude and accuracy of the standards.
A refrigeration system was designed and constructed for realizing a liquid-He-free programmable Josephson voltage standard. The system is equipped with a two-stage Gifford-McMahon cooler, a thermal-radiation shield, a magnetic-field shield and semi-rigid coaxial cables to supply microwave power to a chip. The performance of the system was examined by use of a NbN-based 8-bit digital-to-analog converter (DAC) chip designed as a 1 V programmable voltage standard. When operated at 8.5 K on the cryocooler, constant-voltage steps with amplitudes greater than 1 mA were observed for every segment of junction arrays on the chip.
We have demonstrated a programmable Josephson voltage standard (PJVS) operation up to 10.84 V using a multi-chip technique. We combined two PJVS chips fabricated using NbN/(TiN x /NbN) 2 junction technology. Each PJVS chip was mounted on a single chip carrier using bonding wire, and the two chip carriers were connected by a simple Cu lead wire, and mounted on a cryocooler. High-precision measurements confirmed flat voltage steps for all 22 cells, with a peak-to-peak variation of 100 nV and wide margins of at least 0.35 mA. We also confirmed the stability of the voltage steps in spite of a temperature and RF frequency variation of ± 0.1 K and ± 0.1 GHz, respectively.
For a more wide-spread use of Josephson voltage standards, cryogen-free operation, by means of an appropriate closed-cycle refrigerator, is highly desirable. In this work we present a low-noise pulse tube cooler (PTC) that is capable to cool the voltage standard circuits to temperatures below 4 K. As a low loss dielectric waveguide with a very small thermal conductivity a Teflon strip was used for the microwave transmission. The matched transition from the WR12 rectangular waveguide to the Teflon strip and vice versa was made using special exponential tapers. Programmable 1 Volt 14 bit SINIS and 10 Volt SIS arrays assembled in the PTC operated well, i.e., demonstrated a similar performance to that measured in liquid helium. The Josephson junction arrays were integrated in coplanar strips instead of the commonly used microstriplines for the microwave transmission lines. The 1 Volt SINIS array contained 8192 Josephson junctions (JJs). It generated an inherently stable Josephson voltage step of 1.19 V at a driving microwave frequency of 70 GHz. The step width was 150 /spl mu/A and the critical current of the junctions was 550 /spl mu/A. Similar results were obtained under liquid helium cooling conditions. In another experiment a 10 Volt voltage standard chip with 19700 SIS JJs was installed. It was possible to generate stable Shapiro steps at the 10 V level.