Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Conference on Precision Electromagnetic Measurements

Research Progress on the Cryocooled 10 V Programmable Josephson Voltage Standard at NIM

Zengmin Wang, Honghui Li, Yan Chen, Fujian Liao, Lei Wang, Jiangtao Zhang, Zhengsen Jia

Published Jul 8, 2024• 0 citations
Publisher

Abstract

This paper presents a cryocooled 10 V programmable Josephson voltage standard (PJVS) system including some improvements on overcoming the significant concern of thermal management and electromagnetic noise. The measurement results of operating margin have shown the minimum quantum voltage step of all 23 subarrays is 1.2 mA.
DOI
10.1109/cpem61406.2024.10646106

Related papers

Cryocooled 10 V Programmable Josephson Voltage Standard

Alain Rüfenacht, Logan A. Howe, Anna E. Fox +4 more

The two main challenges to operating a programmable Josephson voltage standard (PJVS) on a cryocooler are the available cooling power and the temperature oscillations of the cold head. We overcame these challenges and successfully operated a PJVS circuit on a cryocooler by employing one supercritical helium buffer that damps the temperature oscillations, developing a new cryogenic package that increases the thermal conductivity between the chip and the cold head, and increasing overall device performance with fabrication improvements. A 1.32 mA step width of the quantized voltage produced with all of the subarrays of the PJVS circuit biased was achieved at an operating temperature of 4.3 K. The quantum accuracy of the PJVS is maintained at temperatures up to 4.8 K. This result was obtained with a cryocooler that employs a 3 kW water-cooled compressor to produce at the chip about 270 mW of net cooling power at 4.3 K.

IEEE Transactions on Instrumentation and Measurement•Dec 11, 2014•37 citations

Demonstration of a 10 V programmable Josephson voltage standard system based on a multi-chip technique

Tatsuji Yamada, Hajime SASAKI, Hirotake Yamamori +1 more

We have demonstrated a programmable Josephson voltage standard (PJVS) operation up to 10.84 V using a multi-chip technique. We combined two PJVS chips fabricated using NbN/(TiN x /NbN) 2 junction technology. Each PJVS chip was mounted on a single chip carrier using bonding wire, and the two chip carriers were connected by a simple Cu lead wire, and mounted on a cryocooler. High-precision measurements confirmed flat voltage steps for all 22 cells, with a peak-to-peak variation of 100 nV and wide margins of at least 0.35 mA. We also confirmed the stability of the voltage steps in spite of a temperature and RF frequency variation of ± 0.1 K and ± 0.1 GHz, respectively.

Superconductor Science and Technology•Feb 1, 2008•14 citations

Cryocooled 10 V Programmable Josephson Voltage Standard

Alain Rüfenacht, Logan A. Howe, Anna E. Fox +4 more

Improvements in fabrication and packaging of our 10 V Programmable Josephson Voltage Standard circuits have enabled the successful operation of these devices on a cryocooler. Limited cooling power and temperature oscillations at the chip must not compromise the accuracy of the quantized voltage steps. Flat-spot measurements of quantized voltages produced with all of the sub-arrays when the chip is biased at a temperature of 4.35 K produced a step width of 0.78 mA. This result was obtained with a cryostat that uses a modest 1.3 kW air-cooled compressor that generates 180 mW of cooling power at the chip.

Conference on Precision Electromagnetic Measurements•Aug 1, 2014•5 citations

Performance of a Cryocooled Nb DC Programmable Voltage Standard at 4 K

Robert J. Webber, Charles J. Burroughs, Masoud Radparvar

We report on the performance of a 1-V dc programmable Josephson voltage standard (PJVS) operating on a commercially available Gifford-McMahon cryocooler at 4 K. The NIST-fabricated niobium superconductor-normal metal-superconductor junction chip has been shown to operate successfully as integrated with this cryopackage, generating 1.229 V at the maximum operating frequency of 19.364 GHz with Shapiro steps at constant voltage that are flat to within less than 100 nV. Because of the large operating margin (greater than 1 mA), these steps were highly stable and immune from noise. Differences in behavior of the PJVS in liquid helium and on the cryocooler are discussed. This demonstration paves the way towards automated warming and cooling of the Josephson device and a fully automated voltage standard system.

IEEE Transactions on Applied Superconductivity•Dec 1, 2007•8 citations

Development of a compact Josephson voltage standard based on NbN/TiN/NbN array operating at 12K

Hajime SASAKI, Hirotake Yamamori, Tatsuji Yamada +2 more

A compact Programmable Josephson Voltage Standard (PJVS) system based on a cryocooler is under development at the National Institute of Advanced Industrial Science and Technology (AIST). The system uses a 2 V NbN/TiN/NbN PJVS chip operating at 12 K. Since the PJVS chip requires cooling power of less than 100 mW, it is possible to use a compact-size cryocooler, which may be mounted inside a standard 19-inch rack-mount chassis. By combining the 2 V PJVS chip with a high-precision semiconductor voltage multiplier circuit, it is possible to generate arbitrary voltages up to 20 V.

Conference on Precision Electromagnetic Measurements•Jun 1, 2010•1 citation

Development of 0.5-V Josephson junction array devices for quantum voltage standards*

Lanruo Wang, Jinjin Li, Wenhui Cao +2 more

The design, fabrication, and the characterization of a 0.5-V Josephson junction array device are presented for the quantum voltage standards in the National Institute of Metrology (NIM) of China. The device consists of four junction arrays, each of which has 1200 3-stacked Nb/Nb x Si1−x /Nb junctions and an on-chip superconducting microwave circuit which is mainly a power divider enabling each Josephson array being loaded with an equal amount of microwave power. A direct current (dc) quantum voltage of about 0.5 V with a ∼1-mA current margin of the 1st quantum voltage step is obtained. To further prove the quality of NIM device, a comparison between the NIM device with the National Institute of Standards and Technology (NIST) programmable Josephson voltage standard (PJVS) system device is conducted. The difference of the reproduced 0.5-V quantum voltage between the two devices is about 0.55 nV, which indicates good agreement between the two devices. With the homemade device, we have realized a precise and applicable 0.5-V applicable-level quantum voltage.

Chinese Physics B•Jun 1, 2019•5 citations
The two main challenges to operating a programmable Josephson voltage standard (PJVS) on a cryocooler are the available cooling power and the temperature oscillations of the cold head. We overcame these challenges and successfully operated a PJVS circuit on a cryocooler by employing one supercritical helium buffer that damps the temperature oscillations, developing a new cryogenic package that increases the thermal conductivity between the chip and the cold head, and increasing overall device performance with fabrication improvements. A 1.32 mA step width of the quantized voltage produced with all of the subarrays of the PJVS circuit biased was achieved at an operating temperature of 4.3 K. The quantum accuracy of the PJVS is maintained at temperatures up to 4.8 K. This result was obtained with a cryocooler that employs a 3 kW water-cooled compressor to produce at the chip about 270 mW of net cooling power at 4.3 K.
We have demonstrated a programmable Josephson voltage standard (PJVS) operation up to 10.84 V using a multi-chip technique. We combined two PJVS chips fabricated using NbN/(TiN x /NbN) 2 junction technology. Each PJVS chip was mounted on a single chip carrier using bonding wire, and the two chip carriers were connected by a simple Cu lead wire, and mounted on a cryocooler. High-precision measurements confirmed flat voltage steps for all 22 cells, with a peak-to-peak variation of 100 nV and wide margins of at least 0.35 mA. We also confirmed the stability of the voltage steps in spite of a temperature and RF frequency variation of ± 0.1 K and ± 0.1 GHz, respectively.
Improvements in fabrication and packaging of our 10 V Programmable Josephson Voltage Standard circuits have enabled the successful operation of these devices on a cryocooler. Limited cooling power and temperature oscillations at the chip must not compromise the accuracy of the quantized voltage steps. Flat-spot measurements of quantized voltages produced with all of the sub-arrays when the chip is biased at a temperature of 4.35 K produced a step width of 0.78 mA. This result was obtained with a cryostat that uses a modest 1.3 kW air-cooled compressor that generates 180 mW of cooling power at the chip.
We report on the performance of a 1-V dc programmable Josephson voltage standard (PJVS) operating on a commercially available Gifford-McMahon cryocooler at 4 K. The NIST-fabricated niobium superconductor-normal metal-superconductor junction chip has been shown to operate successfully as integrated with this cryopackage, generating 1.229 V at the maximum operating frequency of 19.364 GHz with Shapiro steps at constant voltage that are flat to within less than 100 nV. Because of the large operating margin (greater than 1 mA), these steps were highly stable and immune from noise. Differences in behavior of the PJVS in liquid helium and on the cryocooler are discussed. This demonstration paves the way towards automated warming and cooling of the Josephson device and a fully automated voltage standard system.
A compact Programmable Josephson Voltage Standard (PJVS) system based on a cryocooler is under development at the National Institute of Advanced Industrial Science and Technology (AIST). The system uses a 2 V NbN/TiN/NbN PJVS chip operating at 12 K. Since the PJVS chip requires cooling power of less than 100 mW, it is possible to use a compact-size cryocooler, which may be mounted inside a standard 19-inch rack-mount chassis. By combining the 2 V PJVS chip with a high-precision semiconductor voltage multiplier circuit, it is possible to generate arbitrary voltages up to 20 V.
The design, fabrication, and the characterization of a 0.5-V Josephson junction array device are presented for the quantum voltage standards in the National Institute of Metrology (NIM) of China. The device consists of four junction arrays, each of which has 1200 3-stacked Nb/Nb x Si1−x /Nb junctions and an on-chip superconducting microwave circuit which is mainly a power divider enabling each Josephson array being loaded with an equal amount of microwave power. A direct current (dc) quantum voltage of about 0.5 V with a ∼1-mA current margin of the 1st quantum voltage step is obtained. To further prove the quality of NIM device, a comparison between the NIM device with the National Institute of Standards and Technology (NIST) programmable Josephson voltage standard (PJVS) system device is conducted. The difference of the reproduced 0.5-V quantum voltage between the two devices is about 0.55 nV, which indicates good agreement between the two devices. With the homemade device, we have realized a precise and applicable 0.5-V applicable-level quantum voltage.