Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Chinese Physics B

Extending microwave-frequency electric-field detection through single transmission peak method

Qing Liu, Jin-Zhan 进湛 Chen 陈, He 赫 Wang 王, Jie 杰 Zhang 张, Wei-Min 伟民 Ruan 阮, Guo-Zhu 国柱 Wu 伍, Shun-Yuan 顺元 Zheng 郑, Jing-Ting 景庭 Luo 罗, Zhen-Fei 振飞 Song 宋

Published Feb 19, 2024• 1 citation
Publisher

Abstract

The strength of microwave (MW) electric field can be observed with high precision by using the standard electromagnetically induced transparency and Aulter–Towns (EIT-AT) technique, when its frequency is resonant or nearly-resonant with the Rydberg transition frequency. As the detuning of MW field increases, one of the transmission peaks (single peak) is easier to measure due to its increased amplitude. It can be found that the central symmetry point of the two transmission peaks f 1/2 is only related to the detuning of MW field Δ MW and central symmetry point f 0 of resonant MW field, satisfying the relation f 1/2 = Δ MW/2 + f 0. Thus, we demonstrate a single transmission peak method that the MW E-field can be determined by interval between the position of single peak and f 1/2. We use this method to measure continuous frequencies in a band from −200 MHz to 200 MHz of the MW field. The experimental results and theoretical analysis are presented to describe the effectiveness of this method. For 50 MHz < Δ MW < 200 MHz, this method solves the problem that the AT splitting cannot be measured by using the standard EIT-AT techniques or multiple atomic-level Rydberg atom schemes.

DOI
10.1088/1674-1056/ad2a6f

Related papers

Microwave electrometry with bichromatic electromagnetically induced transparency in Rydberg atoms

Mingzhi Han, He Hao, Xiaoyun Song +4 more

Abstract A scheme for measuring microwave (MW) electric (E) fields is proposed based on bichromatic electromagnetically induced transparency (EIT) in Rydberg atoms. A bichromatic control field drives the excited state transition, whose absorption shows three EIT windows. When a MW field drives the Rydberg transition, the EIT windows split and six transmission peaks appear. It is interesting to find that the peak-to-peak distance of transmission spectrum is sensitive to the MW field strength, which can be used to measure MW E-field. Simulation results show that the spectral resolution could be increased by about 4 times, and the minimum detectable strength of the MW E-field may be improved by about 3 times compared with the common EIT scheme. After the Doppler averaging, the minimum detectable MW E-field strength is about 5 times larger than that without Doppler effect. Also, we investigate other effects on the sensitivity of the system.

EPJ Quantum Technology•Jul 14, 2023•8 citations

Extending bandwidth sensitivity of Rydberg-atom-based microwave electrometry using an auxiliary microwave field

Yue Cui, Feng-Dong Jia, Jianhai Hao +13 more

We demonstrate the use of an auxiliary microwave field to extend the bandwidth sensitivity of Rydberg-atom-based microwave electrometry. Electromagnetically induced transparency (EIT) and Autler-Townes (AT) splitting in Rydberg atom microwave electrometry provide advantageous sensitivity for the resonant detection of microwave (MW) fields because the Stark shift of the target Rydberg state takes the linear form of AT splitting. However, the sensitivity is reduced by several orders of magnitude for detuned MW fields because the Stark shift of the target Rydberg state depends on a weak nonlinear effect. We show that the auxiliary microwave field with appropriate Rabi frequency or detuning could shift the atomic energy levels to bring a particular Rydberg-Rydberg transition of interest for microwave sensing into resonance with the target microwave field. Using the atomic superheterodyne method, we verified the general method that regulates Rydberg energy levels using an auxiliary microwave field. The experimental results of this study confirm that this technique works efficiently for detecting microwave fields detuned by up to 100 MHz from resonance with the field-free Rydberg-Rydberg transition used for sensing. The measurement sensitivity of the detuned target field is increased by a factor of 10 compared with that achieved without the application of the auxiliary dressing field.

Physical Review A•Apr 3, 2023•48 citations

Broadband Rydberg atom-based radio-frequency field sensor

Jiao Yue-Chun, Jianming Zhao, Jia Suo-Tang

Significant progress has been made in atom-based measurements of length, time, gravity and electromagnetic fields in recently years. Rydberg atom-based microwave electric field measurement, using electromagnetically induced transparency (EIT) in room temperature alkali-metal vapors, has been extensively investigated and aroused the broad interest. This approach may establish a new standard for the measurements of microwave (MW) and radio frequency (RF) electric fields.In this review, we describe the work on a new method of measuring electric fields based on quantum interference by using either cesium or rubidium atoms contained in a dielectric vapor cell. Rydberg atoms with principal quantum number n >>1 have large direct current (DC) polarizabilities and microwave transition dipole moments, thereby making them extremely sensitive to external electric fields. Using the Rydberg three-level EIT to detect the level splitting and shift that is induced by the external field, we can realize a rapid and robust self-calibration method of measuring the electric field in a frequency range from 0.01 GHz to 1000 GHz. For the MW electric field (frequency range > 1 GHz), the MW field causes the Rydberg states to split, known as an Autler-Townes splitting (A-T) effect when the applied microwave can resonate with adjacent Rydberg states. The MW coupled A-T splitting is proportional to the applied electric field strength, from which the field strength is measured. Using the EIT window, a high sensitivity of 3 μV·cm-1·Hz-1/2 and small electric field of 1 μV/cm are expected to be achieved with a modest setup, and the limitations of the sensitivity are also addressed in the review. For the RF field at frequency mj EIT lines, and avoided crossings formed with the fine-structure levels of equal mj and different J's, which is used to calibrate and measure the RF field amplitude. On the other hand, the dependence of the EIT-line strength on the RF field polarization provides a fast and robust polarization measurement of RF fields based on matching experimental data with a theoretical simulation. The measurements of minimum strengths and sensitivity of RF fields based on Rydberg atoms are one order magnitude below the values obtained by traditional antenna methods. The atom-based field measurement paves the way for determining fields through calibration-free, invariable atomic properties and miniaturization. We also propose its various potential applications in the future.

Acta Physica Sinica•Jan 1, 2018•7 citations

Microwave electric-field measurement with active Raman gain

Aihong Yang, Yandong Peng, Wenpeng Zhou +3 more

An active-Raman-gain (ARG) spectrum of Rydberg atoms is investigated and proposed to measure a microwave (MW) electric (E) field. A strong Raman field couples the ground-state transition with large frequency detuning, and a probe field drives the metastable transition, whose transmission shows a large gain. When a MW field couples the Rydberg transition, the gain peak splits. It is interesting to find that the frequency splitting of gain peaks shows a linear relationship with the MW-field strength, which can be used to measure the MW E field. Moreover, the ARG spectrum has a large peak value that is about 10 times larger than that of common electromagnetically induced transparency schemes. For weak MW fields, the Doppler effect will greatly narrow the gain spectrum if the probe and Raman fields copropagate through the atomic cell, which increases the probe sensitivity dramatically. After the Doppler averaging, the probe sensitivity is enhanced by about 10 times, and the linewidth is narrowed to 1/10 compared to the case without the Doppler effect.

Journal of the Optical Society of America B•Jul 16, 2019•11 citations

Cavity-enhanced microwave electric field measurement using Rydberg atoms

Yandong Peng, Jinling Wang, Aihong Yang +3 more

An enhanced measurement of the microwave electric (MW E) field by using intracavity Rydberg atoms is proposed. Based on electromagnetically induced transparency (EIT), the intracavity atomic system exhibits two EIT windows, resulting in two narrow peaks in the cavity transmission. The peak-to-peak distance is sensitive to MW fields and can be used to probe MW E-field strength. Simulation results show that the detectable minimum strength of the MW fields is nearly eight times smaller than that without a cavity. Due to cavity coupling, the transmission spectrum is greatly narrowed, which improves the measurement resolution substantially. The numerical results show that the spectrum resolution is increased by more than 20 times. Furthermore, the cavity-enhanced measurement scheme seems to be robust against the changes in the control field strength and shows a broadband tunability.

Journal of the Optical Society of America B•Aug 27, 2018•40 citations

Microwave electrometry with Rydberg atoms in a vapor cell using microwave amplitude modulation

Jianhai Hao, Feng-Dong Jia, Yue Cui +9 more

We have theoretically and experimentally studied the dispersive signal of the Rydberg atomic electromagnetically-induced transparency (EIT) Autler–Townes (AT) splitting spectra obtained using amplitude modulation of the microwave (MW) electric field. In addition to the two zero-crossing points interval Δf zeros, the dispersion signal has two positive maxima with an interval defined as the shoulder interval Δf sho, which is theoretically expected to be used to measure a much weaker MW electric field. The relationship of the MW field strength E MW and Δf sho is experimentally studied at the MW frequencies of 31.6 GHz and 9.2 GHz respectively. The results show that Δf sho can be used to characterize the much weaker E MW than that of Δf zeros and the traditional EIT–AT splitting interval Δf m; the minimum E MW measured by Δf sho is about 30 times smaller than that by Δf m. As an example, the minimum E MW at 9.2 GHz that can be characterized by Δf sho is 0.056 mV/cm, which is the minimum value characterized by the frequency interval using a vapor cell without adding any auxiliary fields. The proposed method can improve the weak limit and sensitivity of E MW measured by the spectral frequency interval, which is important in the direct measurement of weak E MW.

arXiv:2304.09316•Chinese Physics B•Jan 4, 2024•17 citations
The strength of microwave (MW) electric field can be observed with high precision by using the standard electromagnetically induced transparency and Aulter–Towns (EIT-AT) technique, when its frequency is resonant or nearly-resonant with the Rydberg transition frequency. As the detuning of MW field increases, one of the transmission peaks (single peak) is easier to measure due to its increased amplitude. It can be found that the central symmetry point of the two transmission peaks f 1/2 is only related to the detuning of MW field Δ MW and central symmetry point f 0 of resonant MW field, satisfying the relation f 1/2 = Δ MW/2 + f 0. Thus, we demonstrate a single transmission peak method that the MW E-field can be determined by interval between the position of single peak and f 1/2. We use this method to measure continuous frequencies in a band from −200 MHz to 200 MHz of the MW field. The experimental results and theoretical analysis are presented to describe the effectiveness of this method. For 50 MHz < Δ MW < 200 MHz, this method solves the problem that the AT splitting cannot be measured by using the standard EIT-AT techniques or multiple atomic-level Rydberg atom schemes.
Abstract A scheme for measuring microwave (MW) electric (E) fields is proposed based on bichromatic electromagnetically induced transparency (EIT) in Rydberg atoms. A bichromatic control field drives the excited state transition, whose absorption shows three EIT windows. When a MW field drives the Rydberg transition, the EIT windows split and six transmission peaks appear. It is interesting to find that the peak-to-peak distance of transmission spectrum is sensitive to the MW field strength, which can be used to measure MW E-field. Simulation results show that the spectral resolution could be increased by about 4 times, and the minimum detectable strength of the MW E-field may be improved by about 3 times compared with the common EIT scheme. After the Doppler averaging, the minimum detectable MW E-field strength is about 5 times larger than that without Doppler effect. Also, we investigate other effects on the sensitivity of the system.
We demonstrate the use of an auxiliary microwave field to extend the bandwidth sensitivity of Rydberg-atom-based microwave electrometry. Electromagnetically induced transparency (EIT) and Autler-Townes (AT) splitting in Rydberg atom microwave electrometry provide advantageous sensitivity for the resonant detection of microwave (MW) fields because the Stark shift of the target Rydberg state takes the linear form of AT splitting. However, the sensitivity is reduced by several orders of magnitude for detuned MW fields because the Stark shift of the target Rydberg state depends on a weak nonlinear effect. We show that the auxiliary microwave field with appropriate Rabi frequency or detuning could shift the atomic energy levels to bring a particular Rydberg-Rydberg transition of interest for microwave sensing into resonance with the target microwave field. Using the atomic superheterodyne method, we verified the general method that regulates Rydberg energy levels using an auxiliary microwave field. The experimental results of this study confirm that this technique works efficiently for detecting microwave fields detuned by up to 100 MHz from resonance with the field-free Rydberg-Rydberg transition used for sensing. The measurement sensitivity of the detuned target field is increased by a factor of 10 compared with that achieved without the application of the auxiliary dressing field.
Significant progress has been made in atom-based measurements of length, time, gravity and electromagnetic fields in recently years. Rydberg atom-based microwave electric field measurement, using electromagnetically induced transparency (EIT) in room temperature alkali-metal vapors, has been extensively investigated and aroused the broad interest. This approach may establish a new standard for the measurements of microwave (MW) and radio frequency (RF) electric fields.In this review, we describe the work on a new method of measuring electric fields based on quantum interference by using either cesium or rubidium atoms contained in a dielectric vapor cell. Rydberg atoms with principal quantum number n >>1 have large direct current (DC) polarizabilities and microwave transition dipole moments, thereby making them extremely sensitive to external electric fields. Using the Rydberg three-level EIT to detect the level splitting and shift that is induced by the external field, we can realize a rapid and robust self-calibration method of measuring the electric field in a frequency range from 0.01 GHz to 1000 GHz. For the MW electric field (frequency range > 1 GHz), the MW field causes the Rydberg states to split, known as an Autler-Townes splitting (A-T) effect when the applied microwave can resonate with adjacent Rydberg states. The MW coupled A-T splitting is proportional to the applied electric field strength, from which the field strength is measured. Using the EIT window, a high sensitivity of 3 μV·cm-1·Hz-1/2 and small electric field of 1 μV/cm are expected to be achieved with a modest setup, and the limitations of the sensitivity are also addressed in the review. For the RF field at frequency mj EIT lines, and avoided crossings formed with the fine-structure levels of equal mj and different J's, which is used to calibrate and measure the RF field amplitude. On the other hand, the dependence of the EIT-line strength on the RF field polarization provides a fast and robust polarization measurement of RF fields based on matching experimental data with a theoretical simulation. The measurements of minimum strengths and sensitivity of RF fields based on Rydberg atoms are one order magnitude below the values obtained by traditional antenna methods. The atom-based field measurement paves the way for determining fields through calibration-free, invariable atomic properties and miniaturization. We also propose its various potential applications in the future.
An active-Raman-gain (ARG) spectrum of Rydberg atoms is investigated and proposed to measure a microwave (MW) electric (E) field. A strong Raman field couples the ground-state transition with large frequency detuning, and a probe field drives the metastable transition, whose transmission shows a large gain. When a MW field couples the Rydberg transition, the gain peak splits. It is interesting to find that the frequency splitting of gain peaks shows a linear relationship with the MW-field strength, which can be used to measure the MW E field. Moreover, the ARG spectrum has a large peak value that is about 10 times larger than that of common electromagnetically induced transparency schemes. For weak MW fields, the Doppler effect will greatly narrow the gain spectrum if the probe and Raman fields copropagate through the atomic cell, which increases the probe sensitivity dramatically. After the Doppler averaging, the probe sensitivity is enhanced by about 10 times, and the linewidth is narrowed to 1/10 compared to the case without the Doppler effect.
An enhanced measurement of the microwave electric (MW E) field by using intracavity Rydberg atoms is proposed. Based on electromagnetically induced transparency (EIT), the intracavity atomic system exhibits two EIT windows, resulting in two narrow peaks in the cavity transmission. The peak-to-peak distance is sensitive to MW fields and can be used to probe MW E-field strength. Simulation results show that the detectable minimum strength of the MW fields is nearly eight times smaller than that without a cavity. Due to cavity coupling, the transmission spectrum is greatly narrowed, which improves the measurement resolution substantially. The numerical results show that the spectrum resolution is increased by more than 20 times. Furthermore, the cavity-enhanced measurement scheme seems to be robust against the changes in the control field strength and shows a broadband tunability.
We have theoretically and experimentally studied the dispersive signal of the Rydberg atomic electromagnetically-induced transparency (EIT) Autler–Townes (AT) splitting spectra obtained using amplitude modulation of the microwave (MW) electric field. In addition to the two zero-crossing points interval Δf zeros, the dispersion signal has two positive maxima with an interval defined as the shoulder interval Δf sho, which is theoretically expected to be used to measure a much weaker MW electric field. The relationship of the MW field strength E MW and Δf sho is experimentally studied at the MW frequencies of 31.6 GHz and 9.2 GHz respectively. The results show that Δf sho can be used to characterize the much weaker E MW than that of Δf zeros and the traditional EIT–AT splitting interval Δf m; the minimum E MW measured by Δf sho is about 30 times smaller than that by Δf m. As an example, the minimum E MW at 9.2 GHz that can be characterized by Δf sho is 0.056 mV/cm, which is the minimum value characterized by the frequency interval using a vapor cell without adding any auxiliary fields. The proposed method can improve the weak limit and sensitivity of E MW measured by the spectral frequency interval, which is important in the direct measurement of weak E MW.