Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Physics Letters

Scanning tunneling microscopy and spectroscopy characterization of Nb films for quantum applications

G. Berti, Carlos G. Torres‐Castanedo, Dominic P. Goronzy, Michael J. Bedzyk, Mark C. Hersam, Cameron Kopas, Jayss Marshall, M. Iavarone

Published May 9, 2023• 13 citations
Publisher

Abstract

Niobium thin films are key components of superconducting microwave resonators. Interest in these devices has increased dramatically because of their application in quantum systems. Despite tremendous effort to improve their performance, loss mechanisms are still not well understood. Nb/substrate and Nb/air interfaces are likely culprits in contributing to decoherence and ultimately limiting the performance of superconducting devices. Here, we investigate the Nb/substrate interface by studying the effect of hydrogen-passivated H:Si(111) substrates on the local superconducting properties of ∼40 nm thick Nb films compared to Nb films grown on typical Si(001) substrates. Specifically, low-temperature scanning tunneling microscopy and spectroscopy are employed to compare nanoscale material properties. The atomically flat monohydride H:Si(111) substrates are found to yield a smoother and less defective interface with the Nb film. Correspondingly, the Nb films grown on H:Si(111) substrates present more uniform superconducting properties and exhibit less quasiparticle broadening.

DOI
10.1063/5.0145090

Related papers

Multi-modal electron microscopy study on decoherence sources and their stability in Nb based superconducting qubit

Jin‐Su Oh, Xiaotian Fang, Taehoon Kim +14 more

Niobium is commonly used for superconducting quantum systems as readout resonators, capacitors, and interconnects. The coherence time of the superconducting qubits is mainly limited by microwave dissipation attributed to two-level system defects at interfaces, such as the Nb/Si and Nb/air interface. One way to improve the Nb/air interface quality is by thermal annealing, as shown by extensive studies in 3D superconducting radio frequency (SRF) cavities. However, it is unclear how the microstructure and chemistry of the interface structures change during heat treatment. To address this knowledge gap, we comprehensively characterized Nb films deposited on Si wafers by physical vapor deposition, including (1) an Nb film from a transmon and (2) an Nb film without any patterning step, using an aberration-corrected transmission electron microscope. Both Nb films exhibit columnar growth with strong [110] textures. There is a double layer between the Nb film and Si substrate, which are amorphous niobium silicides with different Nb and Si concentrations. After in-situ heating of the heterostructure at 360°C inside the microscope, the composition of the double layers at the Nb-Si interface remains almost the same despite different thickness changes. The initial amorphous niobium oxide layer on Nb surface decomposes into face-centered cubic Nb nanograins in the amorphous Nb-O matrix upon heating.

arXiv:2204.06041•Apr 12, 2022•4 citations

Atomic-Scale Characterization and Electronic Properties of Gold-Capped Niobium Films for Superconducting Qubits

Junki Makita, Seth Rice, G. Berti +17 more

Niobium thin films are central to superconducting qubits, but their complex native oxides contribute significantly to microwave losses. A promising mitigation strategy is to suppress oxide formation using engineered thin-film encapsulation layers. Recent experiments have shown that ∼10 nm metallic overlayers on Nb capacitor films can improve the energy relaxation time T 1 of transmon qubits. Here, we present a comparative study of Au-capped Nb films fabricated in situ by molecular beam epitaxy and ex situ by sequential deposition benchmarked against bare Nb films. Using complementary structural, chemical, and spectroscopic techniques, we correlate the interface quality with superconducting electronic properties of the Au surface. Low-temperature scanning tunneling spectroscopy (STS) provides spatially resolved quasiparticle density-of-states maps. While both Au-capped Nb samples exhibit large areas with uniform, fully gapped density of states, clear differences emerge between the two interfaces. Compared to in situ Nb–Au, ex situ Nb–Au exhibits a reduced induced superconducting gap, broadened coherence peak, and localized in-gap states, consistent with a residual Nb x O y layer at the interface. Supported by complementary structural and chemical analyses, these findings demonstrate that STS directly links nanoscale superconducting properties to interface preparation, highlighting the importance of controlled in situ encapsulation for minimizing dissipation and improving quantum coherence.

ACS Nano•Mar 4, 2026•1 citation

Materials Studies of Niobium Thin Films for Quantum Circuit Applications: Progress and Challenges

Ananya Chattaraj, Aswin kumar Anbalagan, J. ‐H. Cho +1 more

ABSTRACT Niobium (Nb) films have emerged as a crucial material in the development of superconducting qubits, which are key components in quantum computing technology. This review provides a comprehensive examination of Nb films from a materials perspective, focusing on their intrinsic properties, fabrication methods/techniques, and their influence on qubit performance, particularly through surface and interface driven loss mechanisms. We discuss the key material properties that are essential for qubit operation. Various deposition techniques for Nb thin films, such as sputtering, evaporation, molecular beam epitaxy, and atomic layer deposition, are explored, alongside their impact on film quality, uniformity, and qubit performance. Additionally, the influence of surface roughness, thin‐film thickness, and substrate materials on quantum coherence is analyzed. Challenges such as defects and material degradation in Nb films are reviewed, along with strategies to mitigate these issues. Finally, we present the latest advancements and future directions in Nb film research, including potential improvements to enhance qubit coherence and scalability for large‐scale quantum computing systems. Ultimately, a deeper understanding of surface and interface phenomena is essential for pushing the limits of qubit performance and realizing next‐generation quantum technologies.

Advanced Quantum Technologies•Jan 1, 2026•3 citations

The effect of niobium thin film structure on losses in superconducting circuits

Maxwell Drimmer, Sjoerd Telkamp, Felix L Fischer +7 more

Abstract The performance of superconducting microwave circuits is strongly influenced by the material properties of the superconducting film and substrate. While progress has been made in understanding the importance of surface preparation and the effect of surface oxides, the complex effect of superconductor film structure on microwave losses is not yet fully understood. In this study, we investigate the microwave properties of niobium resonators with different crystalline properties and related surface topographies. We analyze a series of magnetron sputtered films in which the Nb crystal orientation and surface topography are changed by varying the substrate temperatures between room temperature and 975 K. The lowest-loss resonators that we measure have quality factors of over 10 6 at single-photon powers, among the best ever recorded using the Nb on sapphire platform. We observe the highest quality factors in films grown at an intermediate temperature regime of the growth series (550 K) where the films display both preferential ordering of the crystal domains and low surface roughness. Furthermore, we analyze the temperature-dependent behavior of our resonators to learn about how the quasiparticle density in the Nb film is affected by the niobium crystal structure and the presence of grain boundaries. Our results stress the connection between the crystal structure of superconducting films and the loss mechanisms suffered by the resonators and indicate that even a moderate change in temperature during thin film deposition can significantly affect the resulting quality factors.

arXiv:2403.12164•Materials for Quantum Technology•Oct 14, 2025•22 citations

Effect of Buried-Interface Preparation for Nb Superconducting Resonators on InP

Logan S. Kusher, Ding Peng, Zihua Zhu +14 more

Substrate surface preparation is a key step in the fabrication of electronic devices. In III--V semiconductor platforms, e.g. used in HEMTs and lasers, removal of the native substrate oxide is extremely important, where improper removal will negatively affect end-of-line device performance. However, the impact of substrate preparation in hybrid superconductor--semiconductor (S--Sm) systems relevant to quantum information applications remains poorly understood. This study compares three surface preparations for the deposition of sputtered Nb films on InP: (i) no intentional oxide removal (control), (ii) \textit{in-situ} $\mathrm{Ar}^{+}$ milling, and (iii) S-passivation. \textit{In-situ} $\mathrm{Ar}^{+}$ milling reduces the O concentration at the metal--substrate (MS) interface, but also roughens the InP surface, increasing the effective thickness of the Nb--InP interface and promoting O incorporation through extended defects in the Nb film. S-passivation suppresses interfacial O more effectively while preserving a sharper and smoother buried interface. It also yields Nb films with higher superconducting transition temperatures and less structural damage than the $\mathrm{Ar}^{+}$-milled samples. Despite these materials improvements, the microwave response is comparable across the three preparations. At single photon powers, the highest internal quality factors, $Q_i$, are approximately $1.30\times10^{5}$ ($130\mathrm{k}$) for the control resonators, $9.7\times10^{4}$ ($97\mathrm{k}$) for the S-passivated resonators, and $8.4\times10^{4}$ ($84\mathrm{k}$) for the $\mathrm{Ar}^{+}$-milled resonators. These results suggest that the present devices are not primarily limited by dielectric loss at the buried Nb--InP interface.

arXiv:2609.13673•Sep 12, 2026•0 citations

Investigation of the Superconducting Properties of Nb Filmscovered by PECVD a-Si:H Layers for Superconducting Qubit Application

Alessandro Bruno, P. Mengucci, Lucia Vittoria Mercaldo +1 more

Hydrogenated amorphous silicon (a-Si:H) grown by PECVD has a lower loss tangent (tan _) among conventional dielectrics (such as SiO2 and SiNx) and hence is considered as the best amorphous dielectric material for superconducting qubit application. The incorporation of PECVD a-Si:H into the Nb technology requires attention due to the possible degradation of the superconductivity of the Nb films. Superconducting transition temperature (Tc) and residual resistivity (_0) of 20 nm, 50 nm and 100 nm thick Nb films were measured before and after a-Si:H deposition. The penetration of oxygen and hydrogen inside the Nb films was evaluated from the variation of the lattice parameter obtained by X-ray di_raction. The high process temperature (250_ C) and the presence of energetic hydrogen ions during the a-Si:H layer growth caused a decrease of Tc and increase of _0 through two physical processes: 1) oxygen di_usion from the surface Nb oxides and 2) hydrogen di_usion inside the Nb films. The degradation of Tc was reduced with the increase of the film thickness. Nitridation of Nb films and deposition of a sputtered thin amorphous silicon layer (a-Si) on the Nb films (in both cases made in situ after the Nb film deposition) were investigated a s surface treatments to protect the Nb filmsduring PECVD. It was demonstrated that both methods markedly reduce oxygen and hydrogen di_usion into Nb films during a-Si:H deposition, but the a-Si layer was more e_ective to protect the Nb films.

Physics Procedia•Jan 1, 2012•3 citations
Niobium thin films are key components of superconducting microwave resonators. Interest in these devices has increased dramatically because of their application in quantum systems. Despite tremendous effort to improve their performance, loss mechanisms are still not well understood. Nb/substrate and Nb/air interfaces are likely culprits in contributing to decoherence and ultimately limiting the performance of superconducting devices. Here, we investigate the Nb/substrate interface by studying the effect of hydrogen-passivated H:Si(111) substrates on the local superconducting properties of ∼40 nm thick Nb films compared to Nb films grown on typical Si(001) substrates. Specifically, low-temperature scanning tunneling microscopy and spectroscopy are employed to compare nanoscale material properties. The atomically flat monohydride H:Si(111) substrates are found to yield a smoother and less defective interface with the Nb film. Correspondingly, the Nb films grown on H:Si(111) substrates present more uniform superconducting properties and exhibit less quasiparticle broadening.
Niobium is commonly used for superconducting quantum systems as readout resonators, capacitors, and interconnects. The coherence time of the superconducting qubits is mainly limited by microwave dissipation attributed to two-level system defects at interfaces, such as the Nb/Si and Nb/air interface. One way to improve the Nb/air interface quality is by thermal annealing, as shown by extensive studies in 3D superconducting radio frequency (SRF) cavities. However, it is unclear how the microstructure and chemistry of the interface structures change during heat treatment. To address this knowledge gap, we comprehensively characterized Nb films deposited on Si wafers by physical vapor deposition, including (1) an Nb film from a transmon and (2) an Nb film without any patterning step, using an aberration-corrected transmission electron microscope. Both Nb films exhibit columnar growth with strong [110] textures. There is a double layer between the Nb film and Si substrate, which are amorphous niobium silicides with different Nb and Si concentrations. After in-situ heating of the heterostructure at 360°C inside the microscope, the composition of the double layers at the Nb-Si interface remains almost the same despite different thickness changes. The initial amorphous niobium oxide layer on Nb surface decomposes into face-centered cubic Nb nanograins in the amorphous Nb-O matrix upon heating.
Niobium thin films are central to superconducting qubits, but their complex native oxides contribute significantly to microwave losses. A promising mitigation strategy is to suppress oxide formation using engineered thin-film encapsulation layers. Recent experiments have shown that ∼10 nm metallic overlayers on Nb capacitor films can improve the energy relaxation time T 1 of transmon qubits. Here, we present a comparative study of Au-capped Nb films fabricated in situ by molecular beam epitaxy and ex situ by sequential deposition benchmarked against bare Nb films. Using complementary structural, chemical, and spectroscopic techniques, we correlate the interface quality with superconducting electronic properties of the Au surface. Low-temperature scanning tunneling spectroscopy (STS) provides spatially resolved quasiparticle density-of-states maps. While both Au-capped Nb samples exhibit large areas with uniform, fully gapped density of states, clear differences emerge between the two interfaces. Compared to in situ Nb–Au, ex situ Nb–Au exhibits a reduced induced superconducting gap, broadened coherence peak, and localized in-gap states, consistent with a residual Nb x O y layer at the interface. Supported by complementary structural and chemical analyses, these findings demonstrate that STS directly links nanoscale superconducting properties to interface preparation, highlighting the importance of controlled in situ encapsulation for minimizing dissipation and improving quantum coherence.
ABSTRACT Niobium (Nb) films have emerged as a crucial material in the development of superconducting qubits, which are key components in quantum computing technology. This review provides a comprehensive examination of Nb films from a materials perspective, focusing on their intrinsic properties, fabrication methods/techniques, and their influence on qubit performance, particularly through surface and interface driven loss mechanisms. We discuss the key material properties that are essential for qubit operation. Various deposition techniques for Nb thin films, such as sputtering, evaporation, molecular beam epitaxy, and atomic layer deposition, are explored, alongside their impact on film quality, uniformity, and qubit performance. Additionally, the influence of surface roughness, thin‐film thickness, and substrate materials on quantum coherence is analyzed. Challenges such as defects and material degradation in Nb films are reviewed, along with strategies to mitigate these issues. Finally, we present the latest advancements and future directions in Nb film research, including potential improvements to enhance qubit coherence and scalability for large‐scale quantum computing systems. Ultimately, a deeper understanding of surface and interface phenomena is essential for pushing the limits of qubit performance and realizing next‐generation quantum technologies.
Abstract The performance of superconducting microwave circuits is strongly influenced by the material properties of the superconducting film and substrate. While progress has been made in understanding the importance of surface preparation and the effect of surface oxides, the complex effect of superconductor film structure on microwave losses is not yet fully understood. In this study, we investigate the microwave properties of niobium resonators with different crystalline properties and related surface topographies. We analyze a series of magnetron sputtered films in which the Nb crystal orientation and surface topography are changed by varying the substrate temperatures between room temperature and 975 K. The lowest-loss resonators that we measure have quality factors of over 10 6 at single-photon powers, among the best ever recorded using the Nb on sapphire platform. We observe the highest quality factors in films grown at an intermediate temperature regime of the growth series (550 K) where the films display both preferential ordering of the crystal domains and low surface roughness. Furthermore, we analyze the temperature-dependent behavior of our resonators to learn about how the quasiparticle density in the Nb film is affected by the niobium crystal structure and the presence of grain boundaries. Our results stress the connection between the crystal structure of superconducting films and the loss mechanisms suffered by the resonators and indicate that even a moderate change in temperature during thin film deposition can significantly affect the resulting quality factors.
Substrate surface preparation is a key step in the fabrication of electronic devices. In III--V semiconductor platforms, e.g. used in HEMTs and lasers, removal of the native substrate oxide is extremely important, where improper removal will negatively affect end-of-line device performance. However, the impact of substrate preparation in hybrid superconductor--semiconductor (S--Sm) systems relevant to quantum information applications remains poorly understood. This study compares three surface preparations for the deposition of sputtered Nb films on InP: (i) no intentional oxide removal (control), (ii) \textit{in-situ} Ar+\mathrm{Ar}^{+}Ar+ milling, and (iii) S-passivation. \textit{In-situ} Ar+\mathrm{Ar}^{+}Ar+ milling reduces the O concentration at the metal--substrate (MS) interface, but also roughens the InP surface, increasing the effective thickness of the Nb--InP interface and promoting O incorporation through extended defects in the Nb film. S-passivation suppresses interfacial O more effectively while preserving a sharper and smoother buried interface. It also yields Nb films with higher superconducting transition temperatures and less structural damage than the Ar+\mathrm{Ar}^{+}Ar+-milled samples. Despite these materials improvements, the microwave response is comparable across the three preparations. At single photon powers, the highest internal quality factors, QiQ_iQi​, are approximately 1.30×1051.30\times10^{5}1.30×105 (130k130\mathrm{k}130k) for the control resonators, 9.7×1049.7\times10^{4}9.7×104 (97k97\mathrm{k}97k) for the S-passivated resonators, and 8.4×1048.4\times10^{4}8.4×104 (84k84\mathrm{k}84k) for the Ar+\mathrm{Ar}^{+}Ar+-milled resonators. These results suggest that the present devices are not primarily limited by dielectric loss at the buried Nb--InP interface.
Hydrogenated amorphous silicon (a-Si:H) grown by PECVD has a lower loss tangent (tan _) among conventional dielectrics (such as SiO2 and SiNx) and hence is considered as the best amorphous dielectric material for superconducting qubit application. The incorporation of PECVD a-Si:H into the Nb technology requires attention due to the possible degradation of the superconductivity of the Nb films. Superconducting transition temperature (Tc) and residual resistivity (_0) of 20 nm, 50 nm and 100 nm thick Nb films were measured before and after a-Si:H deposition. The penetration of oxygen and hydrogen inside the Nb films was evaluated from the variation of the lattice parameter obtained by X-ray di_raction. The high process temperature (250_ C) and the presence of energetic hydrogen ions during the a-Si:H layer growth caused a decrease of Tc and increase of _0 through two physical processes: 1) oxygen di_usion from the surface Nb oxides and 2) hydrogen di_usion inside the Nb films. The degradation of Tc was reduced with the increase of the film thickness. Nitridation of Nb films and deposition of a sputtered thin amorphous silicon layer (a-Si) on the Nb films (in both cases made in situ after the Nb film deposition) were investigated a s surface treatments to protect the Nb filmsduring PECVD. It was demonstrated that both methods markedly reduce oxygen and hydrogen di_usion into Nb films during a-Si:H deposition, but the a-Si layer was more e_ective to protect the Nb films.