Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

AIP Advances

Superconducting single-photon detectors fabricated via a focused electron beam-induced deposition process

Stephan Steinhauer, Adrian Iovan, Samuel Gyger, Val Zwiller

Published Apr 1, 2023• 1 citation
Publisher

Abstract

Superconducting detectors have become essential devices for high-performance single-photon counting over a wide wavelength range with excellent time resolution. Detector fabrication typically relies on resist-based lithography processes, which can limit possibilities for device integration, e.g., on unconventional substrates. Here, we demonstrate a resist-free fabrication route for realizing superconducting nanowire single-photon detectors based on focused electron beam-induced deposition. Utilizing direct writing of a Pt–C mask, we achieved nanowire meanders with linewidths below 100 nm, operated them as superconducting devices for the detection of visible and near-infrared photons, and showed detector integration on side-polished optical fibers. Being compatible with device fabrication on curved irregular surfaces, our approach could enable superconducting detector integration in complex configurations.

DOI
10.1063/5.0080674

Related papers

Single-photon and photon-number-resolving detectors based on superconducting nanowires

Francesco Marsili

Nanowire superconducting single photon detectors (SSPDs) [1] are characterized by very high sensitivity in the near infrared (detection efficiency η up to 30%, for a dark count rate DK of few Hz), speed (up to ∼1 GHz repetition rate) and time resolution (jitter of 20 ps full width at half maximum, FWHM). They can be operated at temperatures near 4 K, so they can be packaged in cryogenic dipsticks or cryogen-free refrigerators. These features make SSPDs the most promising detectors for telecom-wavelength single-photon counting applications. The basic structure of an SSPD is a narrow (w=50 to 120 nm), thin (th∼4-10 nm) NbN superconducting nanowire folded in a meander pattern. The typical detector active area (i.e. the size of the pixel) is Ad=10 × 10 µm2 (which allows an efficient coupling with the core of optical fibers at telecom wavelengths) with filling factor (f, the ratio of the area occupied by the superconducting meander to the device total area) ranging from 40% to 60%. The meanders are embedded in a 50 Ω coplanar transmission line. At present, the SSPD detection efficiency is limited by its absorbance (α, the ratio of the number of photons absorbed in the nanowire to the number of incident photons on the device active area). Indeed, it has been shown that in the classic front-illumination configuration α cannot exceed 30%. Our approach to increase α consists in integrating SSPDs with advanced optical structures such as distributed Bragg reflectors (DBRs) and optical waveguides. This requires to transfer the challenging SSPD technology (i.e. the deposition of high-quality few-nm thick NbN films and the nano-patterning by electron beam lithography, EBL) from the usual comfortable substrates, i.e. sapphire and MgO, which are known to allow the deposition of few-nm thick NbN films of excellent quality, to an optical substrate like GaAs, on which DBRs and waveguides can be easily obtained. Our first task was then to optimize a process for the deposition of high-quality few-nm thick NbN films on GaAs and AlAs/GaAs-based DBRs. Because of the requirement of compatibility with GaAs, the substrate temperature used for the depositions is 400°C, in order to prevent As evaporation. As GaAs and DBRs are highly mismatched substrates, the deposition parameters were first optimized with respect to the superconducting properties of NbN films on MgO substrates, which allow the growth of high crystal quality NbN films at low temperature. This made easier to separate the influence of stoichiometry from that of microstructure. The optimized deposition parameters were then used to grow NbN films on GaAs and DBRs, under the reasonable assumption (later checked and confirmed) that changing the substrate would not produce a change in film stoichiometry, but only in its microstructure. NbN films ranging from 150nm to 3nm in thickness were then deposited on epitaxial-quality single crystal MgO, GaAs and DBRs structures. The deposition technique is the current controlled DC magnetron sputtering (planar, circular, balanced configuration) of Nb in an Ar + N2 plasma. NbN films deposited on MgO exhibit superconducting critical temperature ΤC=10 Κ, superconducting transition width ΔΤC=0.8 Κ and residual resistivity ratio RRR=R(20K)/R(300K)=0.8 for th=4 nm, which are state of the art values, proof of the excellent quality of our low-temperature deposition process. The quality of films deposited on GaAs and on DBRs is lower than that of NbN deposited on MgO, as for any thickness they systematically exhibit higher ΔΤC and lower ΤC and RRR. However, 5.5 nm-thick NbN films on GaAs still exhibit ΤC=10.7 Κ, ΔΤC=1.1 Κ and RRR=0.7, which compares with 4.5 nm thick films on MgO, making them suitable for device fabrication. To our knowledge, the growth of such high quality thin NbN films on GaAs and DBRs, has never been reported in literature. The degradation of the superconducting properties exhibited by NbN films on GaAs and DBRs was attributed to a highly defected microstructure, due both to a higher lattice misfit between NbN and GaAs and to a poorer quality of the substrate surface. Encouraging preliminary results show that the quality of these films can be improved either cleaning the GaAs/DBR substrate surface more effectively or adding an MgO buffer layer. SSPDs were fabricated on thin NbN films (th=3-7 nm) deposited under optimal conditions on MgO and GaAs by EBL and reactive ion etching. The geometrical parameters of our detectors are: Ad=5×5 µm2, w=60-200 nm, f=40%-60%. The devices were then characterized both electrically and optically. I-V curves of test structures were measured, from which it was possible to deduce important physical parameters used as figures of merit to estimate the superconducting properties of the nanowires, or for the design and the simulation of the devices. The quality of the devices fabricated on GaAs is poorer than those on MgO, most likely due to the lower quality of NbN films deposited on GaAs and to issues related to the EBL nano-patterning step. Measurements of η and of DK as a function of the bias current were performed on SSPDs fabricated on MgO and GaAs. The best performance was exhibited by a w=100 nm, f=40%, th=4 nm meander, showing η=20% and noise equivalent power NEP=10-16 W/Hz1/2 (at λ=1.3 µm and T=4.2 K), which are state of the art values. This result showed for the first time that high performance NbN SSPDs can be realized on a different substrate and from a deposition process at lower temperature than previously reported. High detection efficiencies could not be measured with SSPDs fabricated on GaAs, but it should be noted that at present only first-generation devices (fabricated on GaAs substrates of poor surface quality) have been tested. Better results are expected from devices fabricated on the improved NbN films grown on clean or MgO-buffered GaAs substrates. Although SSPDs on MgO have shown high detection efficiency, the fabrication yield of high performance detectors has to be improved. Variations of the critical current along a nanowire are responsible for the wide distribution in efficiency values of nominally identical SSPDs. In order to understand the physical origin of the nanowire constrictions (i.e. regions of suppressed superconductivity) we performed a spatially-resolved characterization of η of a long straight nanowire, followed by a high resolution SEM (scanning electron microscope) scan on its whole length. Two types of inhomogeneities were evidenced, corresponding to localized efficiency dips and peaks. The peaks likely correspond to constrictions. SEM observations did not evidence any width narrowing at the position of the efficiency peaks, which suggests that constrictions might be due to thickness or quality inhomogeneities of the film occurring during the film deposition or later in the process. On the other hand, the efficiency dips have been correlated with lithography problems discovered on SEM images. Finally, a new photon number resolving detector, the Parallel Nanowire Detector (PND), has been demonstrated, which significantly outperforms existing approaches in terms of sensitivity, speed and multiplication noise in the telecommunication wavelength range. In particular, it provides a repetition rate (80 MHz) three orders of magnitude larger than any existing detector at telecom wavelength, and a sensitivity (NEP=4.2×10-18 W/Hz1/2) one-two orders of magnitude better, with the exception of transition-edge sensors (which require a much lower operating temperature). An electrical equivalent model of the device was developed in order to study its operation. The modeling predicts a physical limit to the reset time of the PND, which is lower than initially estimated. Furthermore, the figures of merit of the device performance in terms of efficiency, speed and sensitivity were defined and their dependency on the design parameters analyzed. Additionally, we developed modeling tools to fully characterize the device and an algorithm to estimate the photon number statistics of an unknown light using the PND. The reconstruction proved to be successful only for low photon fluxes, most likely due to the limited counting capability and the poor calibration of the detector. The PND, with its high repetition rate and high sensitivity, is then suitable for measuring an unknown photon number probability distribution assuming accurate calibration and sufficient counting capability. ______________________________[1] G. N. Gol'tsman, O. Okunev, G. Chulkova, A. Lipatov, A. Semenov, K. Smirnov, B. Voronov, A. Dzardanov, C. Williams, and R. Sobolewski, Appl. Phys. Lett. 79, 705 (2001).

•Jan 1, 2009•4 citations

Fabrication of superconducting nanowire single-photon detectors by nonlinear femtosecond optical lithography

Н. В. Минаев, Michael A. Tarkhov, D. S. Dudova +3 more

Abstract This paper describes a new approach to the fabrication of superconducting nanowire single-photon detectors from ultrathin NbN films on SiO 2 substrates. The technology is based on nonlinear femtosecond optical lithography and includes direct formation of the sensitive element of the detector (the meander) through femtosecond laser exposure of the polymethyl methacrylate resist at a wavelength of 525 nm and subsequent removal of NbN using plasma-chemical etching. The nonlinear femtosecond optical lithography method allows the formation of planar structures with a spatial resolution of ~50 nm. These structures were used to fabricate single-photon superconducting detectors with quantum efficiency no worse than 8% at a wavelength of 1310 nm and dark count rate of 10 s −1 at liquid helium temperature.

Laser Physics Letters•Jan 9, 2018•14 citations

Advances in Superconducting Single-photon Detectors

Kyle DeBry

Superconducting single-photon detectors can detect photons from the UV to the infrared with quantum efficiencies above 90% and greater than MHz count rates. They consist of narrow, thin wires of superconductor biased near their critical current. When these wires absorb a photon, part of the wire stops superconducting and becomes resistive. This transition and sudden jump in resistance is what enables the detection of the photon. Over the past two decades, these devices have matured greatly as a technology and have found many applications ranging from quantum optics to astronomy. However, there are still multiple theories of the dominant mechanism behind these devices. Recently proposed theories suggest a more complicated but potentially more powerful detection mechanism, and experiments are only recently starting to demonstrate this effect and its potential applications. In this research, the capability to fabricate these intricate devices was developed. This requires high-quality deposition of the superconductors, precise machining of the devices with electron beam lithography, and accurate etching of the films. Many parts of the process have been characterized. Additionally, two new directions are being explored. The first attempts to exploit the recently proposed detection mechanism to make detectors with much wider wires, leading to faster detection rates. The second is the fabrication of superconducting single-photon detectors directly onto optical fibers, eliminating the need for complicated coupling structures and alignment of the detector with the fiber.

•May 1, 2020•0 citations

Broadband waveguide-integrated superconducting single-photon detectors with high system detection efficiency

Martin A. Wolff, Fabian Beutel, Jonas Schütte +4 more

Fast and efficient detection of single photons with high timing accuracy is a crucial requirement in most quantum optics experiments and enables novel sensing and imaging solutions. Superconducting nanowire single-photon detectors (SNSPD) achieve technology-leading performance in terms of detection efficiency, dark count rate, timing jitter, and detector dead times. However, conventional SNSPDs with high system detection efficiency typically rely on resonant enhancement of the absorption efficiency, thus only achieving attractive detector benchmarks over narrow spectral windows. Waveguide-integrated SNSPDs allow for leveraging the wideband material absorption in superconducting nanowires by absorbing light in a traveling-wave geometry but have been limited to low system detection efficiencies due to interface losses when coupling to optical fibers. Here, we show how high system detection efficiencies of 22%–73% are realized over a broad wavelength range from 532 nm to 1640 nm in a single waveguide-integrated SNSPD device. We accomplish efficient coupling between optical fibers and waveguide-integrated nanowire detectors by employing a 3D interface, produced in direct laser writing, that relies on total internal reflection for achieving a broad transmission bandwidth. We further find low timing jitter of 25.7 ps and detector decay times of 9.8 ns, allowing for single-photon counting with high repetition rates up to 100 MHz. Our work paves the way for an efficient single-photon detector solution that combines the spectral requirements of an extremely wide range of quantum optics experiments in a single device. The coupling approach and SNSPD-integration with nanophotonic circuits are further well-suited for realizing large-scale detector arrays.

Applied Physics Letters•Apr 12, 2021•48 citations

Atomic-layer deposited mid-infrared sensitive NbTiN superconducting nanowire single photon detectors

Nidhi Choudhary, Dmitry Morozov, Daniel Kuznesof +7 more

Abstract The advancement of superconducting nanowire single-photon detectors (SNSPDs or SSPDs) is intrinsically linked to breakthroughs in superconducting materials engineering. These detectors are prized for their excellent sensitivity and performance across a wide wavelength range, from ultra-violet to mid-infrared (mid-IR). Plasma-enhanced atomic layer deposition (ALD) is an advanced deposition technique that enables exceptional film uniformity across large wafers, making it ideal for a variety of applications. In this study, ALD NbTiN films are fabricated into SNSPDs that exhibit single-photon response across near- to mid-IR wavelengths. A 5 nm thick NbTiN film was patterned into devices consisting of ∼100 nm wide meandered nanowires, and the nanowire cross-section and composition were analysed by transmission electron microscopy. The devices were tested in a closed-cycle cryostat with a base temperature of 0.9 K. Photon detection rate and timing jitter were measured across the wavelength range 1.5–4.4 µ m under low dark count conditions, confirming single-photon sensitivity across the measured wavelength bands. This work introduces the ALD-grown NbTiN films as a new platform for SNSPD detectors, achieving mid-IR single-photon sensitivity. The intact film quality after fabrication demonstrates the potential of ALD processes for scalable infrared detector technologies.

Superconductor Science and Technology•Apr 1, 2026•1 citation

NbN nanowire superconducting single photon detectors fabricated on MgO substrates

Francesco Marsili, David Bitauld, Alessandro Gaggero +6 more

High sensitivity ultrafast nanowire superconducting single photon detectors (SSPD) in the near infrared wavelength range have been fabricated with ultrathin (3.5nm) NbN films grown on R-plane sapphire substrates by dc reactive magnetron sputtering in Ar+N2mixture. These results show for the first time that high performance NbN SSPDs can be realized on different substrates and at lower deposition temperature than previously reported, and opens the way to integration with advanced solid state optical structures. SSPDs have been fabricated by a two mask process using electron beam lithography and reactive ion etching on 3.5nm thick NbN films deposited under optimal conditions on MgO.

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•Jun 1, 2007•0 citations
Superconducting detectors have become essential devices for high-performance single-photon counting over a wide wavelength range with excellent time resolution. Detector fabrication typically relies on resist-based lithography processes, which can limit possibilities for device integration, e.g., on unconventional substrates. Here, we demonstrate a resist-free fabrication route for realizing superconducting nanowire single-photon detectors based on focused electron beam-induced deposition. Utilizing direct writing of a Pt–C mask, we achieved nanowire meanders with linewidths below 100 nm, operated them as superconducting devices for the detection of visible and near-infrared photons, and showed detector integration on side-polished optical fibers. Being compatible with device fabrication on curved irregular surfaces, our approach could enable superconducting detector integration in complex configurations.
Nanowire superconducting single photon detectors (SSPDs) [1] are characterized by very high sensitivity in the near infrared (detection efficiency η up to 30%, for a dark count rate DK of few Hz), speed (up to ∼1 GHz repetition rate) and time resolution (jitter of 20 ps full width at half maximum, FWHM). They can be operated at temperatures near 4 K, so they can be packaged in cryogenic dipsticks or cryogen-free refrigerators. These features make SSPDs the most promising detectors for telecom-wavelength single-photon counting applications. The basic structure of an SSPD is a narrow (w=50 to 120 nm), thin (th∼4-10 nm) NbN superconducting nanowire folded in a meander pattern. The typical detector active area (i.e. the size of the pixel) is Ad=10 × 10 µm2 (which allows an efficient coupling with the core of optical fibers at telecom wavelengths) with filling factor (f, the ratio of the area occupied by the superconducting meander to the device total area) ranging from 40% to 60%. The meanders are embedded in a 50 Ω coplanar transmission line. At present, the SSPD detection efficiency is limited by its absorbance (α, the ratio of the number of photons absorbed in the nanowire to the number of incident photons on the device active area). Indeed, it has been shown that in the classic front-illumination configuration α cannot exceed 30%. Our approach to increase α consists in integrating SSPDs with advanced optical structures such as distributed Bragg reflectors (DBRs) and optical waveguides. This requires to transfer the challenging SSPD technology (i.e. the deposition of high-quality few-nm thick NbN films and the nano-patterning by electron beam lithography, EBL) from the usual comfortable substrates, i.e. sapphire and MgO, which are known to allow the deposition of few-nm thick NbN films of excellent quality, to an optical substrate like GaAs, on which DBRs and waveguides can be easily obtained. Our first task was then to optimize a process for the deposition of high-quality few-nm thick NbN films on GaAs and AlAs/GaAs-based DBRs. Because of the requirement of compatibility with GaAs, the substrate temperature used for the depositions is 400°C, in order to prevent As evaporation. As GaAs and DBRs are highly mismatched substrates, the deposition parameters were first optimized with respect to the superconducting properties of NbN films on MgO substrates, which allow the growth of high crystal quality NbN films at low temperature. This made easier to separate the influence of stoichiometry from that of microstructure. The optimized deposition parameters were then used to grow NbN films on GaAs and DBRs, under the reasonable assumption (later checked and confirmed) that changing the substrate would not produce a change in film stoichiometry, but only in its microstructure. NbN films ranging from 150nm to 3nm in thickness were then deposited on epitaxial-quality single crystal MgO, GaAs and DBRs structures. The deposition technique is the current controlled DC magnetron sputtering (planar, circular, balanced configuration) of Nb in an Ar + N2 plasma. NbN films deposited on MgO exhibit superconducting critical temperature ΤC=10 Κ, superconducting transition width ΔΤC=0.8 Κ and residual resistivity ratio RRR=R(20K)/R(300K)=0.8 for th=4 nm, which are state of the art values, proof of the excellent quality of our low-temperature deposition process. The quality of films deposited on GaAs and on DBRs is lower than that of NbN deposited on MgO, as for any thickness they systematically exhibit higher ΔΤC and lower ΤC and RRR. However, 5.5 nm-thick NbN films on GaAs still exhibit ΤC=10.7 Κ, ΔΤC=1.1 Κ and RRR=0.7, which compares with 4.5 nm thick films on MgO, making them suitable for device fabrication. To our knowledge, the growth of such high quality thin NbN films on GaAs and DBRs, has never been reported in literature. The degradation of the superconducting properties exhibited by NbN films on GaAs and DBRs was attributed to a highly defected microstructure, due both to a higher lattice misfit between NbN and GaAs and to a poorer quality of the substrate surface. Encouraging preliminary results show that the quality of these films can be improved either cleaning the GaAs/DBR substrate surface more effectively or adding an MgO buffer layer. SSPDs were fabricated on thin NbN films (th=3-7 nm) deposited under optimal conditions on MgO and GaAs by EBL and reactive ion etching. The geometrical parameters of our detectors are: Ad=5×5 µm2, w=60-200 nm, f=40%-60%. The devices were then characterized both electrically and optically. I-V curves of test structures were measured, from which it was possible to deduce important physical parameters used as figures of merit to estimate the superconducting properties of the nanowires, or for the design and the simulation of the devices. The quality of the devices fabricated on GaAs is poorer than those on MgO, most likely due to the lower quality of NbN films deposited on GaAs and to issues related to the EBL nano-patterning step. Measurements of η and of DK as a function of the bias current were performed on SSPDs fabricated on MgO and GaAs. The best performance was exhibited by a w=100 nm, f=40%, th=4 nm meander, showing η=20% and noise equivalent power NEP=10-16 W/Hz1/2 (at λ=1.3 µm and T=4.2 K), which are state of the art values. This result showed for the first time that high performance NbN SSPDs can be realized on a different substrate and from a deposition process at lower temperature than previously reported. High detection efficiencies could not be measured with SSPDs fabricated on GaAs, but it should be noted that at present only first-generation devices (fabricated on GaAs substrates of poor surface quality) have been tested. Better results are expected from devices fabricated on the improved NbN films grown on clean or MgO-buffered GaAs substrates. Although SSPDs on MgO have shown high detection efficiency, the fabrication yield of high performance detectors has to be improved. Variations of the critical current along a nanowire are responsible for the wide distribution in efficiency values of nominally identical SSPDs. In order to understand the physical origin of the nanowire constrictions (i.e. regions of suppressed superconductivity) we performed a spatially-resolved characterization of η of a long straight nanowire, followed by a high resolution SEM (scanning electron microscope) scan on its whole length. Two types of inhomogeneities were evidenced, corresponding to localized efficiency dips and peaks. The peaks likely correspond to constrictions. SEM observations did not evidence any width narrowing at the position of the efficiency peaks, which suggests that constrictions might be due to thickness or quality inhomogeneities of the film occurring during the film deposition or later in the process. On the other hand, the efficiency dips have been correlated with lithography problems discovered on SEM images. Finally, a new photon number resolving detector, the Parallel Nanowire Detector (PND), has been demonstrated, which significantly outperforms existing approaches in terms of sensitivity, speed and multiplication noise in the telecommunication wavelength range. In particular, it provides a repetition rate (80 MHz) three orders of magnitude larger than any existing detector at telecom wavelength, and a sensitivity (NEP=4.2×10-18 W/Hz1/2) one-two orders of magnitude better, with the exception of transition-edge sensors (which require a much lower operating temperature). An electrical equivalent model of the device was developed in order to study its operation. The modeling predicts a physical limit to the reset time of the PND, which is lower than initially estimated. Furthermore, the figures of merit of the device performance in terms of efficiency, speed and sensitivity were defined and their dependency on the design parameters analyzed. Additionally, we developed modeling tools to fully characterize the device and an algorithm to estimate the photon number statistics of an unknown light using the PND. The reconstruction proved to be successful only for low photon fluxes, most likely due to the limited counting capability and the poor calibration of the detector. The PND, with its high repetition rate and high sensitivity, is then suitable for measuring an unknown photon number probability distribution assuming accurate calibration and sufficient counting capability. ______________________________[1] G. N. Gol'tsman, O. Okunev, G. Chulkova, A. Lipatov, A. Semenov, K. Smirnov, B. Voronov, A. Dzardanov, C. Williams, and R. Sobolewski, Appl. Phys. Lett. 79, 705 (2001).
Abstract This paper describes a new approach to the fabrication of superconducting nanowire single-photon detectors from ultrathin NbN films on SiO 2 substrates. The technology is based on nonlinear femtosecond optical lithography and includes direct formation of the sensitive element of the detector (the meander) through femtosecond laser exposure of the polymethyl methacrylate resist at a wavelength of 525 nm and subsequent removal of NbN using plasma-chemical etching. The nonlinear femtosecond optical lithography method allows the formation of planar structures with a spatial resolution of ~50 nm. These structures were used to fabricate single-photon superconducting detectors with quantum efficiency no worse than 8% at a wavelength of 1310 nm and dark count rate of 10 s −1 at liquid helium temperature.
Superconducting single-photon detectors can detect photons from the UV to the infrared with quantum efficiencies above 90% and greater than MHz count rates. They consist of narrow, thin wires of superconductor biased near their critical current. When these wires absorb a photon, part of the wire stops superconducting and becomes resistive. This transition and sudden jump in resistance is what enables the detection of the photon. Over the past two decades, these devices have matured greatly as a technology and have found many applications ranging from quantum optics to astronomy. However, there are still multiple theories of the dominant mechanism behind these devices. Recently proposed theories suggest a more complicated but potentially more powerful detection mechanism, and experiments are only recently starting to demonstrate this effect and its potential applications. In this research, the capability to fabricate these intricate devices was developed. This requires high-quality deposition of the superconductors, precise machining of the devices with electron beam lithography, and accurate etching of the films. Many parts of the process have been characterized. Additionally, two new directions are being explored. The first attempts to exploit the recently proposed detection mechanism to make detectors with much wider wires, leading to faster detection rates. The second is the fabrication of superconducting single-photon detectors directly onto optical fibers, eliminating the need for complicated coupling structures and alignment of the detector with the fiber.
Fast and efficient detection of single photons with high timing accuracy is a crucial requirement in most quantum optics experiments and enables novel sensing and imaging solutions. Superconducting nanowire single-photon detectors (SNSPD) achieve technology-leading performance in terms of detection efficiency, dark count rate, timing jitter, and detector dead times. However, conventional SNSPDs with high system detection efficiency typically rely on resonant enhancement of the absorption efficiency, thus only achieving attractive detector benchmarks over narrow spectral windows. Waveguide-integrated SNSPDs allow for leveraging the wideband material absorption in superconducting nanowires by absorbing light in a traveling-wave geometry but have been limited to low system detection efficiencies due to interface losses when coupling to optical fibers. Here, we show how high system detection efficiencies of 22%–73% are realized over a broad wavelength range from 532 nm to 1640 nm in a single waveguide-integrated SNSPD device. We accomplish efficient coupling between optical fibers and waveguide-integrated nanowire detectors by employing a 3D interface, produced in direct laser writing, that relies on total internal reflection for achieving a broad transmission bandwidth. We further find low timing jitter of 25.7 ps and detector decay times of 9.8 ns, allowing for single-photon counting with high repetition rates up to 100 MHz. Our work paves the way for an efficient single-photon detector solution that combines the spectral requirements of an extremely wide range of quantum optics experiments in a single device. The coupling approach and SNSPD-integration with nanophotonic circuits are further well-suited for realizing large-scale detector arrays.
Abstract The advancement of superconducting nanowire single-photon detectors (SNSPDs or SSPDs) is intrinsically linked to breakthroughs in superconducting materials engineering. These detectors are prized for their excellent sensitivity and performance across a wide wavelength range, from ultra-violet to mid-infrared (mid-IR). Plasma-enhanced atomic layer deposition (ALD) is an advanced deposition technique that enables exceptional film uniformity across large wafers, making it ideal for a variety of applications. In this study, ALD NbTiN films are fabricated into SNSPDs that exhibit single-photon response across near- to mid-IR wavelengths. A 5 nm thick NbTiN film was patterned into devices consisting of ∼100 nm wide meandered nanowires, and the nanowire cross-section and composition were analysed by transmission electron microscopy. The devices were tested in a closed-cycle cryostat with a base temperature of 0.9 K. Photon detection rate and timing jitter were measured across the wavelength range 1.5–4.4 µ m under low dark count conditions, confirming single-photon sensitivity across the measured wavelength bands. This work introduces the ALD-grown NbTiN films as a new platform for SNSPD detectors, achieving mid-IR single-photon sensitivity. The intact film quality after fabrication demonstrates the potential of ALD processes for scalable infrared detector technologies.
High sensitivity ultrafast nanowire superconducting single photon detectors (SSPD) in the near infrared wavelength range have been fabricated with ultrathin (3.5nm) NbN films grown on R-plane sapphire substrates by dc reactive magnetron sputtering in Ar+N2mixture. These results show for the first time that high performance NbN SSPDs can be realized on different substrates and at lower deposition temperature than previously reported, and opens the way to integration with advanced solid state optical structures. SSPDs have been fabricated by a two mask process using electron beam lithography and reactive ion etching on 3.5nm thick NbN films deposited under optimal conditions on MgO.