Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Lightwave Technology

Accurate Shot-Noise-Limited Calibration of a Time-Domain Balanced Homodyne Detector for Continuous-Variable Quantum Key Distribution

Xuyang Wang, Xubo Guo, Yan-Xiang Jia, Yu Zhang, Zhenguo Lu, Jianqiang Liu, Yongmin Li

Published Apr 3, 2023• 12 citations
Publisher

Abstract

The time-domain balanced homodyne detector (TBHD) is critical component in continuous-variable quantum key distribution (CVQKD). The shot-noise-limited attribute of a TBHD depends on the whole frequency spectrum of the detector, in contrast to a frequency-domain balanced homodyne detector that focuses only on part of the frequency spectrum. We propose a method for accurate calibration of the shot-noise-limited attribute of the TBHD by overlapping the gain lines of the TBHD and an integral photodetector which is realized by blocking one photodiode of the TBHD. The overlapping of two lines indicates that the detector is indeed shot noise limited, which is crucial to the security of CVQKD. Experimentally, we use this method to obtain a calibration error of$\pm 1$‰. Theoretical analysis showed that the CVQKD security is very sensitive to calibration errors of shot noise, and proper countermeasure was proposed to eliminate this issue. The presented methods are expected to contribute to CVQKD security and TBHD standardization.

DOI
10.1109/jlt.2023.3264234

Related papers

Rigorous calibration of homodyne detection efficiency for continuous-variable quantum key distribution

Mi Zou, Yingqiu Mao, Teng‐Yun Chen

We propose a rigorous calibration method for homodyne detection efficiency, which combines all the factors that affect detection efficiency to calibrate together through the actual homodyne detection. With this method, the transmittance converted from electronic noise in the one-time calibration method of the shot noise can be attributed to the detection inefficiency. Thus, a trusted detection noise-free model for continuous-variable quantum key distribution (CV-QKD) can be established, which simplifies the calibration of shot noise while having the same performance as the trusted detection noise model. We demonstrate this calibration method with a balanced detector based on a transimpedance amplifier. Experimental results show that detection efficiency will be overestimated if the integration factor of the detector is overlooked. The overestimation of the detection efficiency leads to an underestimation of modulation variance and excess noise when the modulation variance is monitored by the balanced detector, which opens security loopholes. Our method may prove a necessary method in the calibration of detection efficiency for CV-QKD.

Optics Express•May 29, 2022•12 citations

A 300-MHz Bandwidth Balanced Homodyne Detector for Continuous Variable Quantum Key Distribution

Duan Huang, Jian Fang, Chao Wang +2 more

In Gaussian-modulated coherent-state quantum key distribution, the measurement of quadratures of coherent states is performed by using a homodyne detector. However, conventional detectors usually suffer from narrow bands. We present a method to design a high-speed shot-noise-limited balanced homodyne detector. A 300-MHz bandwidth detector is experimentally tested and the level of shot noise is 14 dB higher than the electronic noise. The results show that a detector with this method is potential to design a GHz bandwidth detector for continuous variable quantum key distribution at a low level of ratio of shot noise to electronic noise.

Chinese Physics Letters•Nov 1, 2013•66 citations

Silicon photonics-integrated time-domain balanced homodyne detector for quantum tomography and quantum key distribution

Yan-Xiang Jia, Xuyang Wang, Xiao Hu +8 more

Abstract We designed and experimentally demonstrated a silicon photonics-integrated time-domain balanced homodyne detector (TBHD), containing an optical part of dimensions of 1.5 mm × 0.4 mm. To automatically and accurately balance the detector, new variable optical attenuators were used, and a common mode rejection ratio of 86.9 dB could be achieved. In the quantum tomography experiment, the density matrix and Wigner function of a coherent state were reconstructed with 99.97% fidelity. The feasibility of this TBHD in a continuous-variable quantum key distribution (CVQKD) system was also demonstrated. Our TBHD technologies are expected to be used in silicon photonics-integrated CVQKD system and silicon photonics-integrated BB84 heterodyne system.

arXiv:2305.03419•New Journal of Physics•Sep 25, 2023•19 citations

Continuous-Variable Measurement-Device-Independent Quantum Key Distribution with One-Time Shot-Noise Unit Calibration

Luyu Huang, Yichen Zhang, Song Yu

Imperfections in practical detectors, including limited detection efficiency, and inherent electronic noise, can seriously decrease the transmission distance of continuous-variable measurement-device-independent quantum key distribution systems. Owing to the difficulties inherent in realizing a high-efficiency fiber homodyne detector, challenges still exist in continuous-variable measurement-device-independent quantum key distribution system implementation. We offer an alternative approach in an attempt to solve these difficulties and improve the potential for system implementation. Here, a novel practical detector modeling method is utilized, which is combined with a one-time shot-noise-unit calibration method for the purpose of system realization. The new modeling method benefits greatly from taking advantage of one-time shot-noise-unit calibration methods, such as measuring electronic noise and shot noise directly to a novel shot-noise unit, so as to eliminate the statistical fluctuations found in previous methods; this makes the implementation of such systems simpler, and the calibration progress more accurate. We provide a simulation of the secret key rate versus distance with different parameters. In addition, the minimal detection efficiency required at each distance, as well as the contrast between the two methods, are also shown, so as to provide a reference in terms of system realization.

Chinese Physics Letters•May 1, 2021•14 citations

One-Time Shot-Noise Unit Calibration Method for Continuous-Variable Quantum Key Distribution

Yichen Zhang, Yundi Huang, Ziyang Chen +3 more

The shot-noise unit in continuous-variable quantum key distribution plays an important and fundamental role in experimental implementation, as it is used as a normalization parameter that contributes to performing security analyses and distilling key information. However, the traditional calibration procedure and detector model cannot cover all system noise in practical applications, which results in loopholes and influences the practical security. What is more, the traditional procedure is also rather complicated and has difficulty in providing compatibility with automatic operating systems. In this paper, we propose a calibration model based on a proposed trusted detector model, which could naturally close the loopholes in practical applications. It can help to identify the shot-noise unit in only one step, which can not only effectively simplify the evaluation process but also reduce the statistical fluctuations, while two steps are needed in the traditional method. We prove its feasibility and derive a complete version of the corresponding entanglement-based model. A detailed security analysis against arbitrary collective attacks and numerous simulation results in both the asymptotic-limit regime and the finite-size regime are provided. A proof-of-principle experiment is implemented, and the results indicate that our one-time calibration model can be employed as a powerful alternative method for calibrating the shot-noise unit. Our method paves the way for the deployment of continuous-variable quantum key distribution with real-time calibration and automatic operation.

arXiv:1908.06230•Physical Review Applied•Feb 21, 2020•45 citations

Precise Noise Calibration for CV-QKD

Hans H. Brunner, Stefano Bettelli, Chi‐Hang Fred Fung +1 more

Continuous-variable quantum-key-distribution (CV-QKD) devices, conveniently based on standard components from the domain of coherent optical communication, can guarantee an information-theoretic secure-key expansion. Their security analysis assumes that all power lost in the channel, as well as channel noise in excess with respect to the shot noise, is due to an eavesdropper limited only by quantum mechanics. Quantifying the excess noise, which typically has significantly less power than the shot noise, is essential for secure-key generation. In this article a heterodyne-receiver setup capable of measuring optical power with an extremely high sensitivity (approximately -130 dBm within a 12.5 MHz bandwidth at 1550 nm, corresponding to a power 40 dB below the shot noise) is analysed and demonstrated in a CV -QKD prototype device. Such accuracy is achieved by means of continuous calibration and long-time averages.

International Conference on Transparent Optical Networks•Jul 1, 2020•6 citations
The time-domain balanced homodyne detector (TBHD) is critical component in continuous-variable quantum key distribution (CVQKD). The shot-noise-limited attribute of a TBHD depends on the whole frequency spectrum of the detector, in contrast to a frequency-domain balanced homodyne detector that focuses only on part of the frequency spectrum. We propose a method for accurate calibration of the shot-noise-limited attribute of the TBHD by overlapping the gain lines of the TBHD and an integral photodetector which is realized by blocking one photodiode of the TBHD. The overlapping of two lines indicates that the detector is indeed shot noise limited, which is crucial to the security of CVQKD. Experimentally, we use this method to obtain a calibration error of±1\pm 1±1‰. Theoretical analysis showed that the CVQKD security is very sensitive to calibration errors of shot noise, and proper countermeasure was proposed to eliminate this issue. The presented methods are expected to contribute to CVQKD security and TBHD standardization.
We propose a rigorous calibration method for homodyne detection efficiency, which combines all the factors that affect detection efficiency to calibrate together through the actual homodyne detection. With this method, the transmittance converted from electronic noise in the one-time calibration method of the shot noise can be attributed to the detection inefficiency. Thus, a trusted detection noise-free model for continuous-variable quantum key distribution (CV-QKD) can be established, which simplifies the calibration of shot noise while having the same performance as the trusted detection noise model. We demonstrate this calibration method with a balanced detector based on a transimpedance amplifier. Experimental results show that detection efficiency will be overestimated if the integration factor of the detector is overlooked. The overestimation of the detection efficiency leads to an underestimation of modulation variance and excess noise when the modulation variance is monitored by the balanced detector, which opens security loopholes. Our method may prove a necessary method in the calibration of detection efficiency for CV-QKD.
In Gaussian-modulated coherent-state quantum key distribution, the measurement of quadratures of coherent states is performed by using a homodyne detector. However, conventional detectors usually suffer from narrow bands. We present a method to design a high-speed shot-noise-limited balanced homodyne detector. A 300-MHz bandwidth detector is experimentally tested and the level of shot noise is 14 dB higher than the electronic noise. The results show that a detector with this method is potential to design a GHz bandwidth detector for continuous variable quantum key distribution at a low level of ratio of shot noise to electronic noise.
Abstract We designed and experimentally demonstrated a silicon photonics-integrated time-domain balanced homodyne detector (TBHD), containing an optical part of dimensions of 1.5 mm × 0.4 mm. To automatically and accurately balance the detector, new variable optical attenuators were used, and a common mode rejection ratio of 86.9 dB could be achieved. In the quantum tomography experiment, the density matrix and Wigner function of a coherent state were reconstructed with 99.97% fidelity. The feasibility of this TBHD in a continuous-variable quantum key distribution (CVQKD) system was also demonstrated. Our TBHD technologies are expected to be used in silicon photonics-integrated CVQKD system and silicon photonics-integrated BB84 heterodyne system.
Imperfections in practical detectors, including limited detection efficiency, and inherent electronic noise, can seriously decrease the transmission distance of continuous-variable measurement-device-independent quantum key distribution systems. Owing to the difficulties inherent in realizing a high-efficiency fiber homodyne detector, challenges still exist in continuous-variable measurement-device-independent quantum key distribution system implementation. We offer an alternative approach in an attempt to solve these difficulties and improve the potential for system implementation. Here, a novel practical detector modeling method is utilized, which is combined with a one-time shot-noise-unit calibration method for the purpose of system realization. The new modeling method benefits greatly from taking advantage of one-time shot-noise-unit calibration methods, such as measuring electronic noise and shot noise directly to a novel shot-noise unit, so as to eliminate the statistical fluctuations found in previous methods; this makes the implementation of such systems simpler, and the calibration progress more accurate. We provide a simulation of the secret key rate versus distance with different parameters. In addition, the minimal detection efficiency required at each distance, as well as the contrast between the two methods, are also shown, so as to provide a reference in terms of system realization.
The shot-noise unit in continuous-variable quantum key distribution plays an important and fundamental role in experimental implementation, as it is used as a normalization parameter that contributes to performing security analyses and distilling key information. However, the traditional calibration procedure and detector model cannot cover all system noise in practical applications, which results in loopholes and influences the practical security. What is more, the traditional procedure is also rather complicated and has difficulty in providing compatibility with automatic operating systems. In this paper, we propose a calibration model based on a proposed trusted detector model, which could naturally close the loopholes in practical applications. It can help to identify the shot-noise unit in only one step, which can not only effectively simplify the evaluation process but also reduce the statistical fluctuations, while two steps are needed in the traditional method. We prove its feasibility and derive a complete version of the corresponding entanglement-based model. A detailed security analysis against arbitrary collective attacks and numerous simulation results in both the asymptotic-limit regime and the finite-size regime are provided. A proof-of-principle experiment is implemented, and the results indicate that our one-time calibration model can be employed as a powerful alternative method for calibrating the shot-noise unit. Our method paves the way for the deployment of continuous-variable quantum key distribution with real-time calibration and automatic operation.
Continuous-variable quantum-key-distribution (CV-QKD) devices, conveniently based on standard components from the domain of coherent optical communication, can guarantee an information-theoretic secure-key expansion. Their security analysis assumes that all power lost in the channel, as well as channel noise in excess with respect to the shot noise, is due to an eavesdropper limited only by quantum mechanics. Quantifying the excess noise, which typically has significantly less power than the shot noise, is essential for secure-key generation. In this article a heterodyne-receiver setup capable of measuring optical power with an extremely high sensitivity (approximately -130 dBm within a 12.5 MHz bandwidth at 1550 nm, corresponding to a power 40 dB below the shot noise) is analysed and demonstrated in a CV -QKD prototype device. Such accuracy is achieved by means of continuous calibration and long-time averages.