Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Sensors

Aligning Superconducting Transition-Edge Sensors by Reflected Wave Intensity Measurement

Pei-Sa Ma, Hong-Fan Zhang, Xingxiang Zhou

Published Mar 27, 2023• 3 citations
Publisher

Abstract

It is critical to accurately align a quantum photon detector such as a superconducting transition-edge sensor (TES) to an optical fiber in order to optimize its detection efficiency. Conventionally, such alignment requires advanced infrared imaging equipment or sophisticated microfabrication. We introduce a novel technique based on the simple idea of reflected wave intensity measurement which allows to determine the boundary of the sensor and align it accurately with the fiber. By routing a light wave through an optical fiber for normal incidence on the surface of the sensor chip, and separating the reflected wave coupled back into the fiber from the input signal with a circulator, we can observe the variation in the reflected wave intensity when the beam spot of the fiber crosses the boundary between the sensor and substrate that have different reflectivity, and adjust the position of the fiber such that its output falls on the sensor. We evaluate quantitatively the precision of our alignment method, as well as the conditions that must be met to avoid photon loss caused by light beam divergence. After demonstrating the working principle of our scheme and verifying the alignment result experimentally, we employ it for efficient input signal coupling to a TES device, which is used for photon-number-resolving measurement to showcase the successful application of our alignment method in practice. Relying on only ordinary and widely used optical elements that are easy to operate and low in cost, our solution is much less demanding than conventional methods. Dramatically easier to implement and not restricted by the detection mechanism of the sensor, it is accessible to a much broader community.

DOI
10.3390/s23073495

Related papers

Improvement of Ti-based Superconducting Transition Edge Sensors with Dielectric Mirror

Peng Li, Jinfeng Wang, S. C. Shi +8 more

We have improved the detection efficiency of Ti-based superconducting transition edge sensor(TES) with the integration of dielectric mirror at the operation wavelength of 1550 nm. The TES fabricated on the dielectric mirror is coupled to the optical fiber using back-side through-chip imaging. The measured effective response time is several μs and the detection efficiency is improved to 30%.

International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz)•Sep 1, 2019•2 citations

Multimode Fiber Coupled Superconducting Nanowire Transition Edge Sensor for Detection of Single-Photon at Optical and Near-Infrared Wave Lengths

B. Lokeswara Rao, L. L. Narayana

We report the development of the multimode fiber-coupled superconducting nanowire transition edge sensor with high system detection efficiency at optical and near-infrared wavelength. The SNTES consists of an absorber, a sensitive thermometer, and a weak thermal link to a cold bath, For a SNTES optimized to detect single photons, the temperature change caused by the absorption of a single photo is read out by the thermometer, and the system resets by cooling through the thermal link. The graded index (GRIN) lenses were spliced to the end of the multi mode fiber with a 50 µm diameter core, and the incident light spot diameter was focused to approximately 20 µm at the active area, which is 28 µm diameter, allowing a good optical coupling. We have achieved a nominal coupling efficiency of 91 % and system efficiency of 76 % by the SNTES at 1310 nm -1350 nm. The developed practical SNTES presented in this paper could open a new frontier for a wide range of applications at optical and infrared wavelength.

•Jan 1, 2015•0 citations

Optimizing Optical TESs for High-Efficiency Multimode Fiber Coupling

Federico Malnati, Greta Andrini, Hobey Garrone +6 more

Transition-Edge Sensors (TESs) are superconducting photon detectors offering high quantum efficiency, energy resolution, and photon-number discrimination, making them attractive for quantum sensing applications. We report on the design, fabrication, and characterization of a Ti/Au/Ti TES optimized for multimode fiber coupling in NV-center experiments. The device integrates a bi-layer anti-reflective coating optimized for 700 nm, the emission wavelength range of NV centers in which we are interested. Optical characterization in a cryogenic setup demonstrated an energy resolution below 2 eV and photon-number resolution capability. A dedicated calibration setup was used to evaluate the system detection efficiency (SDE), yielding$0.85 \pm 0.02$. These results confirm the suitability of large-area TESs for efficient multimode fiber coupling and highlight their potential for improving the performance of NV-center-based quantum sensing experiments.

IEEE Transactions on Applied Superconductivity•Mar 23, 2026•0 citations

Influence analysis of gap distance between single-mode fiber and transition edge single-photon sensors

Peizhan Li, Jiaqiang Zhong, Yue Geng +3 more

Optical transition-edge sensor (TES) with high quantum efficiency, low dark count rate, and high energy resolution has been used in quantum information and communications. The gap distance between the fiber tip and TES has an influence on the TES performance. Here we measured the interference pattern of our optical TES devices with and without anti-reflection coating and obtain the gap distance. We also obtain the absolute reflectivity of the Ti-TESs by correcting the effect of power splitter and circulator. Our copper block shrinks ~10 μm when cooled from room temperature down to 100 mK. The measured reflectivity is consistent with the simulation taking the dielectric mirror, Ti film and anti-reflection coating into account. In addition, we study the gap distance dependence of the system efficiency, and find that it is in good agreement with the measured reflectivity at 100 mK. These analyses are useful for further improvement of TES packaging.

International Symposium on Ultrafast Phenomena and Terahertz Waves (ISUPTW)•Sep 9, 2021•3 citations

Counting near-infrared single-photons with 95% efficiency

Adriana E. Lita, Aaron Miller, Sae Woo Nam

Single-photon detectors operating at visible and near-infrared wavelengths with high detection efficiency and low noise are a requirement for many quantum-information applications. Superconducting transition-edge sensors (TESs) are capable of detecting visible and near-infrared light at the single-photon level and are capable of discriminating between one- and two-photon absorption events; however these capabilities place stringent design requirements on the TES heat capacity, thermometry, and optical detection efficiency. We describe the fabrication and evaluation of a fiber-coupled, photon-number-resolving TES detector optimized for absorption at 1550 and 1310 nm wavelengths. The measured system detection efficiency at 1556 nm is 95 % +/- 2 %, which to our knowledge is the highest system detection efficiency reported for a near-infrared single-photon detector.

Optics Express•Jan 1, 2008•733 citations

Photothermal resistivity alignment of optical fibers to superconducting nanowire single-photon detectors

Martin Baránek, Dušan Lorenc, T. Ščepka +5 more

We demonstrate a straightforward optoelectronic fiber alignment technique for superconducting nanowire single-photon detectors (SNSPDs), which exploits the temperature-dependent resistance of a nanowire under optical absorption. The target nanowire is illuminated via the fiber, and the local absorption of light heats the wire, causing a change in its resistivity. Scanning the fiber over the nanowire, the change in its resistivity is monitored by lock-in amplifier, mapping the spatial photothermal response correlated with absorption and coupling efficiency. The maximum of the response corresponds to optimal fiber-SNSPD alignment. This method allows for aligning the fiber to the center of the meander with sub-micron precision. The response is robust to variations in the angle and height of the fiber, providing an alternative or complement to fiber-to-chip alignment methods based on the back-reflection or transmission measurement.

arXiv:2511.09498•Review of Scientific Instruments•Mar 1, 2026•0 citations
It is critical to accurately align a quantum photon detector such as a superconducting transition-edge sensor (TES) to an optical fiber in order to optimize its detection efficiency. Conventionally, such alignment requires advanced infrared imaging equipment or sophisticated microfabrication. We introduce a novel technique based on the simple idea of reflected wave intensity measurement which allows to determine the boundary of the sensor and align it accurately with the fiber. By routing a light wave through an optical fiber for normal incidence on the surface of the sensor chip, and separating the reflected wave coupled back into the fiber from the input signal with a circulator, we can observe the variation in the reflected wave intensity when the beam spot of the fiber crosses the boundary between the sensor and substrate that have different reflectivity, and adjust the position of the fiber such that its output falls on the sensor. We evaluate quantitatively the precision of our alignment method, as well as the conditions that must be met to avoid photon loss caused by light beam divergence. After demonstrating the working principle of our scheme and verifying the alignment result experimentally, we employ it for efficient input signal coupling to a TES device, which is used for photon-number-resolving measurement to showcase the successful application of our alignment method in practice. Relying on only ordinary and widely used optical elements that are easy to operate and low in cost, our solution is much less demanding than conventional methods. Dramatically easier to implement and not restricted by the detection mechanism of the sensor, it is accessible to a much broader community.
We report the development of the multimode fiber-coupled superconducting nanowire transition edge sensor with high system detection efficiency at optical and near-infrared wavelength. The SNTES consists of an absorber, a sensitive thermometer, and a weak thermal link to a cold bath, For a SNTES optimized to detect single photons, the temperature change caused by the absorption of a single photo is read out by the thermometer, and the system resets by cooling through the thermal link. The graded index (GRIN) lenses were spliced to the end of the multi mode fiber with a 50 µm diameter core, and the incident light spot diameter was focused to approximately 20 µm at the active area, which is 28 µm diameter, allowing a good optical coupling. We have achieved a nominal coupling efficiency of 91 % and system efficiency of 76 % by the SNTES at 1310 nm -1350 nm. The developed practical SNTES presented in this paper could open a new frontier for a wide range of applications at optical and infrared wavelength.
Transition-Edge Sensors (TESs) are superconducting photon detectors offering high quantum efficiency, energy resolution, and photon-number discrimination, making them attractive for quantum sensing applications. We report on the design, fabrication, and characterization of a Ti/Au/Ti TES optimized for multimode fiber coupling in NV-center experiments. The device integrates a bi-layer anti-reflective coating optimized for 700 nm, the emission wavelength range of NV centers in which we are interested. Optical characterization in a cryogenic setup demonstrated an energy resolution below 2 eV and photon-number resolution capability. A dedicated calibration setup was used to evaluate the system detection efficiency (SDE), yielding0.85±0.020.85 \pm 0.020.85±0.02. These results confirm the suitability of large-area TESs for efficient multimode fiber coupling and highlight their potential for improving the performance of NV-center-based quantum sensing experiments.
Optical transition-edge sensor (TES) with high quantum efficiency, low dark count rate, and high energy resolution has been used in quantum information and communications. The gap distance between the fiber tip and TES has an influence on the TES performance. Here we measured the interference pattern of our optical TES devices with and without anti-reflection coating and obtain the gap distance. We also obtain the absolute reflectivity of the Ti-TESs by correcting the effect of power splitter and circulator. Our copper block shrinks ~10 μm when cooled from room temperature down to 100 mK. The measured reflectivity is consistent with the simulation taking the dielectric mirror, Ti film and anti-reflection coating into account. In addition, we study the gap distance dependence of the system efficiency, and find that it is in good agreement with the measured reflectivity at 100 mK. These analyses are useful for further improvement of TES packaging.
Single-photon detectors operating at visible and near-infrared wavelengths with high detection efficiency and low noise are a requirement for many quantum-information applications. Superconducting transition-edge sensors (TESs) are capable of detecting visible and near-infrared light at the single-photon level and are capable of discriminating between one- and two-photon absorption events; however these capabilities place stringent design requirements on the TES heat capacity, thermometry, and optical detection efficiency. We describe the fabrication and evaluation of a fiber-coupled, photon-number-resolving TES detector optimized for absorption at 1550 and 1310 nm wavelengths. The measured system detection efficiency at 1556 nm is 95 % +/- 2 %, which to our knowledge is the highest system detection efficiency reported for a near-infrared single-photon detector.
We demonstrate a straightforward optoelectronic fiber alignment technique for superconducting nanowire single-photon detectors (SNSPDs), which exploits the temperature-dependent resistance of a nanowire under optical absorption. The target nanowire is illuminated via the fiber, and the local absorption of light heats the wire, causing a change in its resistivity. Scanning the fiber over the nanowire, the change in its resistivity is monitored by lock-in amplifier, mapping the spatial photothermal response correlated with absorption and coupling efficiency. The maximum of the response corresponds to optimal fiber-SNSPD alignment. This method allows for aligning the fiber to the center of the meander with sub-micron precision. The response is robust to variations in the angle and height of the fiber, providing an alternative or complement to fiber-to-chip alignment methods based on the back-reflection or transmission measurement.