Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Annual Meeting Optical Society of America

Submicrometer direct-write optical lithography with cold atoms

Mara Goff Prentiss, Karl K. Berggren, Gregory L. Timp, Robert E. Behringer, J. E. Cunningham

Published Jan 1, 1992• 0 citations
Publisher

Abstract

We passed a transversely cooled sodium atomic beam through an optical standing wave, which channeled the atoms into the intensity minima (maxima) for light tuned below (above) the sodium 32S1/2 → 32P3/2 resonance frequency. The channeled atoms retained their spatial distribution when they were deposited onto the silicon surface. The surface was thus covered by a permanent periodic sodium grating with an area of 1 x 0.1 cm2 and a period of d = 294.3 ±0.3 nm, which is half the wavelength of the standing wave field. The entire grating was completed in 10 min. We measured the period of the grating by backscattering weak probe light. The probe light had a wavelength λ, which we varied between 5580 and 5800 Å, and was incident at an angle ϕ relative to the normal. There is constructive interference when the angle θ with respect to the normal to the grating is such that λ = d(sin θ + sin ϕ). The dependence of θ on ϕ allowed us to measure d. Semiclassical theory suggests the width of the lines in the grating could be of the order of 100 Å.

DOI
10.1364/oam.1992.thuu1

Related papers

Atom Lithography with a Chromium Atomic Beam

Zhang Wen-Tao, Tongbao Li

Direct write atom lithography is a new technique in which resonant light is used to pattern an atomic beam and the nanostructures are formed when the atoms deposit on the substrate. We design an experiment setup to fabricate chromium nanolines by depositing an atomic beam of 52 Cr through an off-resonant laser standing wave with the wavelength of 425.55 nm onto a silicon substrate. The resulting nanolines exhibit a period of 215±3 nm with height of 1 nm.

Chinese Physics Letters•Oct 26, 2006•4 citations

Using light as a lens for submicron, neutral-atom lithography

Gregory L. Timp, Robert E. Behringer, D. M. Tennant +3 more

We show that light can be used as a lens to focus a collimated neutral atomic beam to submicron dimensions during deposition onto a substrate. We have used an optical standing wave at 589 nm as an array of cylindrical lenses to focus a perpendicular sodium beam into a grating on a substrate, with a periodicity of 294.3\ifmmode\pm\else\textpm\fi{}0.3 nm. This result is the first direct evidence of submicron focusing of atoms by light, and represents a fundamentally new scheme for submicron lithography.

Physical Review Letters•Sep 14, 1992•375 citations

Calculation of atomic positions in nanometer-scale direct-write optical lithography with an optical standing wave

Karl K. Berggren, Mara Goff Prentiss, Gregory L. Timp +1 more

Recent experiments have shown that the light pressure force that is due to an optical standing wave (SW) focuses an atomic beam to submicrometer dimensions. We calculate some theoretical limits on the focusing of a sodium atomic beam by a SW optical field.

Journal of the Optical Society of America B•Jul 1, 1994•46 citations

Magnetic nanostructures by atom optics

Smeets, B (Bart)

Direct-write atom lithography is a technique in which highly periodic nanostructures are directly deposited on a substrate by patterning an atomic beam with a standing light wave, tuned near a resonance frequency of the corresponding atom. In this thesis an extension of this technique for the production of ferromagnetic nano- structures is investigated. Of all ferromagnetic elements Fe is the most suitable to per- form atom lithography. Light with a wavelength of 372 nm is needed to produce Fe nanostructures by atom lithography. Also, the atomic beam should be highly collimated, for which laser cooling is commonly used. For this purpose, a frequency doubled Ti:S laser tuned to 744 nm is constructed, capable of producing more than 100 mW of light at a wavelength of 372 nm. Laser cooling requires a laser with a frequency stability better than the natural linewidth of the atom. To meet this requirement, the laser is locked on the atomic transition by means of polarization spectroscopy on a hollow cathode discharge cell. The discharge cell produces a sufficient density of ground state Fe atoms at a temperature which is more than a factor of two lower than the temperature necessary to produce that density in a thermal cell. With this technique the laser is locked stable within 0.2 MHz for hours. A laser cooling simulation based on the semiclassical approach is presented. Although the intention was to simulate laser cooling of Fe with this code, for the commonly used pxpy polarization gradient configuration an analysis of the simulation results shows that the semiclassical approach is only valid for transitions with recoil parameters ¿r on the order of 10¡4 or less. For the standard laser cooling transitions only the transitions in Rb and Cs satisfy this condition. A drastic reduction in calculation time compared to quantum Monte-Carlo calculations is to be expected for these transitions by implementing an analytical approach to the long-term contribution of the diffusion coefficient. For Fe, full quantum Monte-Carlo calculations are necessary. Laser cooling of Fe on the 372 nm transition has been studied experimentally. This transition, although the only one realistically available, is far from perfect for laser cooling, as it is not a fully closed transition: it has a leak ratio of approximately 1/240 to other states. Nevertheless, a collimation of aRMS = 0.17 mrad could be achieved by laser cooling. However, contrary to the normally obtained central beam flux increase, the ground state atom flux decreased to approximately 70 % of the non-cooled value. Because of both the complexity of the laser cooling setup and the restrictions in perfor- mance, we have also attempted to produce Fe nanostructures without using laser cooling techniques, but simply relying on geometrical collimation of the atomic beam. In this way, Fe nanolines are deposited with a pitch of 186 nm, a FWHM width of 50 nm, and a height of up to 6 nm. This opens the way for applying direct-write atom lithography to a wide variety of elements. In a MOKE (Magneto-Optical Kerr effect)-setup we are able to verify that the deposited Fe-layer is ferromagnetic. However, the magnetic anisotropy due to the presence of the nanolines can not be detected with a MOKE-setup or a MFM (Magnetic Force Microscope). In contrast, the magnetization of background-free nano- lines, deposited through a mechanical mask with a pitch of 744 nm and a FWHM of

•Jan 1, 2005•2 citations

Light force cooling, focusing, and nanometer-scale deposition of aluminum atoms

Roger W. McGowan, David M. Giltner, S. A. Lee

We deposited neutral-aluminum atoms in thin parallel lines to form a grating with a line separation of 154.7 nm by using near-resonant laser light and direct-write optical lithography techniques. We did this by using the single-frequency closed UV transition from the second ground state 3p2P3/2 (F = 4) to 3d2D5/2 (F = 5) at 309.4 nm. The aluminum features were analyzed with an atomic-force microscope.

Optics Letters•Dec 15, 1995•181 citations

Non-linear optical effects in cold and hot rubidium gases

A. J. van Lange

CoverThe front cover shows a microscope image of a bridge waveguide, with tapered launchpads at each side.The launchpads contain the surface grating couplers designed in chapter 2 of this thesis.The freestanding, 200 nm wide and 100 µm long bridge was fabricated using e-beam lithography in a 220 nm thin silicon nitride membrane by Andries Lof at the Amolf Nanolab Amsterdam.The image is taken in the Fourier microscope setup shown in figure 2.5, with white light illumination using an LED.The back cover shows an image of the same bridge waveguide, which is mirrored to represent the bottom view of the sample.It is best viewed by holding the thesis face up and lifting it over your head to investigate the 'sample' from underneath.For this image, the bottom launchpad is illuminated with laserlight with a wavelength of 780 nm under an angle of 3 • from normal incidence.The light is coupled into the membrane and funneled into the waveguide bridge.A bright spot is visible at the waveguide bridge entrance due to enhanced scattering.The light then travels through the bridge and is coupled out at the top launchpad.The image demonstrates that light can be coupled into the nanophotonic waveguide bridge using surface grating couplers under near-normal incidence.

•Aug 18, 2020•0 citations
We passed a transversely cooled sodium atomic beam through an optical standing wave, which channeled the atoms into the intensity minima (maxima) for light tuned below (above) the sodium 32S1/2 → 32P3/2 resonance frequency. The channeled atoms retained their spatial distribution when they were deposited onto the silicon surface. The surface was thus covered by a permanent periodic sodium grating with an area of 1 x 0.1 cm2 and a period of d = 294.3 ±0.3 nm, which is half the wavelength of the standing wave field. The entire grating was completed in 10 min. We measured the period of the grating by backscattering weak probe light. The probe light had a wavelength λ, which we varied between 5580 and 5800 Å, and was incident at an angle ϕ relative to the normal. There is constructive interference when the angle θ with respect to the normal to the grating is such that λ = d(sin θ + sin ϕ). The dependence of θ on ϕ allowed us to measure d. Semiclassical theory suggests the width of the lines in the grating could be of the order of 100 Å.
We show that light can be used as a lens to focus a collimated neutral atomic beam to submicron dimensions during deposition onto a substrate. We have used an optical standing wave at 589 nm as an array of cylindrical lenses to focus a perpendicular sodium beam into a grating on a substrate, with a periodicity of 294.3\ifmmode\pm\else\textpm\fi{}0.3 nm. This result is the first direct evidence of submicron focusing of atoms by light, and represents a fundamentally new scheme for submicron lithography.
Direct-write atom lithography is a technique in which highly periodic nanostructures are directly deposited on a substrate by patterning an atomic beam with a standing light wave, tuned near a resonance frequency of the corresponding atom. In this thesis an extension of this technique for the production of ferromagnetic nano- structures is investigated. Of all ferromagnetic elements Fe is the most suitable to per- form atom lithography. Light with a wavelength of 372 nm is needed to produce Fe nanostructures by atom lithography. Also, the atomic beam should be highly collimated, for which laser cooling is commonly used. For this purpose, a frequency doubled Ti:S laser tuned to 744 nm is constructed, capable of producing more than 100 mW of light at a wavelength of 372 nm. Laser cooling requires a laser with a frequency stability better than the natural linewidth of the atom. To meet this requirement, the laser is locked on the atomic transition by means of polarization spectroscopy on a hollow cathode discharge cell. The discharge cell produces a sufficient density of ground state Fe atoms at a temperature which is more than a factor of two lower than the temperature necessary to produce that density in a thermal cell. With this technique the laser is locked stable within 0.2 MHz for hours. A laser cooling simulation based on the semiclassical approach is presented. Although the intention was to simulate laser cooling of Fe with this code, for the commonly used pxpy polarization gradient configuration an analysis of the simulation results shows that the semiclassical approach is only valid for transitions with recoil parameters ¿r on the order of 10¡4 or less. For the standard laser cooling transitions only the transitions in Rb and Cs satisfy this condition. A drastic reduction in calculation time compared to quantum Monte-Carlo calculations is to be expected for these transitions by implementing an analytical approach to the long-term contribution of the diffusion coefficient. For Fe, full quantum Monte-Carlo calculations are necessary. Laser cooling of Fe on the 372 nm transition has been studied experimentally. This transition, although the only one realistically available, is far from perfect for laser cooling, as it is not a fully closed transition: it has a leak ratio of approximately 1/240 to other states. Nevertheless, a collimation of aRMS = 0.17 mrad could be achieved by laser cooling. However, contrary to the normally obtained central beam flux increase, the ground state atom flux decreased to approximately 70 % of the non-cooled value. Because of both the complexity of the laser cooling setup and the restrictions in perfor- mance, we have also attempted to produce Fe nanostructures without using laser cooling techniques, but simply relying on geometrical collimation of the atomic beam. In this way, Fe nanolines are deposited with a pitch of 186 nm, a FWHM width of 50 nm, and a height of up to 6 nm. This opens the way for applying direct-write atom lithography to a wide variety of elements. In a MOKE (Magneto-Optical Kerr effect)-setup we are able to verify that the deposited Fe-layer is ferromagnetic. However, the magnetic anisotropy due to the presence of the nanolines can not be detected with a MOKE-setup or a MFM (Magnetic Force Microscope). In contrast, the magnetization of background-free nano- lines, deposited through a mechanical mask with a pitch of 744 nm and a FWHM of
CoverThe front cover shows a microscope image of a bridge waveguide, with tapered launchpads at each side.The launchpads contain the surface grating couplers designed in chapter 2 of this thesis.The freestanding, 200 nm wide and 100 µm long bridge was fabricated using e-beam lithography in a 220 nm thin silicon nitride membrane by Andries Lof at the Amolf Nanolab Amsterdam.The image is taken in the Fourier microscope setup shown in figure 2.5, with white light illumination using an LED.The back cover shows an image of the same bridge waveguide, which is mirrored to represent the bottom view of the sample.It is best viewed by holding the thesis face up and lifting it over your head to investigate the 'sample' from underneath.For this image, the bottom launchpad is illuminated with laserlight with a wavelength of 780 nm under an angle of 3 • from normal incidence.The light is coupled into the membrane and funneled into the waveguide bridge.A bright spot is visible at the waveguide bridge entrance due to enhanced scattering.The light then travels through the bridge and is coupled out at the top launchpad.The image demonstrates that light can be coupled into the nanophotonic waveguide bridge using surface grating couplers under near-normal incidence.