Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Physics Letters

Characterization of a low-noise superconductor–insulator–superconductor-based microwave amplifier with local oscillator phase-adjusting architecture

Takafumi Kojima, Sho Masui, Wenlei Shan, Yoshinori Uzawa

Published Feb 13, 2023• 9 citations
Publisher

Abstract

This paper describes a low-noise microwave amplifier based on up- and down-frequency-conversion processes in quasiparticle superconductor–insulator–superconductor (SIS) tunnel junctions. The SIS amplifier was configured with two SIS frequency-converter modules and a cryogenic millimeter-wave isolator inserted between them. Moreover, a local oscillator (LO) using millimeter-wave attenuators and a phase shifter was considered. This setup allowed the control of individual LO power and differential phase in these SIS frequency converters to optimize the amplifier performance. The SIS amplifier showed noise temperatures as low as 11 K and a 6–8 dB gain from nearly DC to 5 GHz. The attained microwave performance is promising for obtaining large-format arrays, such as multibeam heterodyne receivers. Moreover, this two-frequency-converter concept based on SIS junctions might enable microwave applications, such as wideband non-reciprocal circuits in isolators, gyrators, and circulators, which are essential devices in the quantum computing and radio astronomy fields.

DOI
10.1063/5.0134595

Related papers

Microwave amplification based on quasiparticle SIS up and down frequency converters

Takafumi Kojima, Yoshinori Uzawa, Wenlei Shan

Heterodyne instruments have recently attained quantum-limited low-noise performance, particularly in radio astronomy, but it is difficult to develop large heterodyne arrays such as a modern radio camera using cryogenic sensitive detectors based on microwave kinetic inductance detectors, transition edge sensors, etc. In the realization of the heterodyne array, the reduction of power dissipation for semiconductor-based amplifiers remains a major challenge. Alternatively, superconducting parametric amplifiers still seem to have several barriers to application, especially in terms of operating temperature. Here, we show a novel concept of microwave amplification based on up and down frequency-conversion processes using quasiparticle superconductor-insulator-superconductor (SIS) tunnel junctions. We demonstrate positive gain using a proof-of-concept test module, which operates with a power dissipation of several μW at a bath temperature of 4 K. The performance of the module suggests great potential for application in large arrays.

AIP Advances•Feb 1, 2018•17 citations

Development of an SIS Mixer-Based Low-Noise Amplifier Amenable to Josephson Oscillator Pumping

Yoshinori Uzawa, Takafumi Kojima, Kazumasa Makise +4 more

We propose a low-noise and low-power-consumption microwave amplifier using superconductor-insulator-superconductor (SIS) mixers as quasi-particle frequency up- and down-converters pumped by a Josephson array oscillator in the millimeter-wave band. A proof-of-concept study of an amplifier with two W-band waveguide mixers using Nb/Al-AlOx/Nb junctions in a cascade connection demonstrated an average gain of 6 dB and a noise temperature of 12 K from nearly DC to 5 GHz. We also designed and fabricated a Josephson array oscillator at 100 GHz, which consisted of 31 overdamped Josephson junctions placed at each half-wavelength in an Nb microstrip line. The estimated output power of the oscillator was 0.2 μW at 100 GHz, which can be increased by increasing the number of the oscillator junctions. These results suggest that the proposed SIS mixer-based amplifier is suitable for on-chip integrated circuits to be implemented in large-scale multipixel SIS receivers and quantum computers.

IEEE Transactions on Applied Superconductivity•Mar 8, 2023•6 citations

An SIS-mixer-based amplifier for multi-pixel heterodyne receivers

Yoshinori Uzawa, Takafumi Kojima, Yuto Kozuki +5 more

We are investigating a possible microwave amplifier with low noise and low power consumption at cryogenic temperature for large scale multi-pixel heterodyne superconductor-insulator-superconductor (SIS) receivers at millimeter and submillimeter wavelengths. We propose the use of SIS junctions as amplifier elements based on quasi-particle mixing. By connecting an SIS up-converter and an SIS down-converter in series with gain in both converters, a lownoise and low-power-consumption high-frequency amplifier can be obtained in principle. A proof-of-concept study has been made by configuring an amplifier with two Nb/Al-AlOx/Nb mixers in the 150-GHz band in a standard noise and gain measurement setup at 4 K with a microwave noise source as an input signal. We observed a maximum gain of more than 10 dB and a minimum noise temperature of less than 10 K, which suggests that our proposed SIS amplifier is capable for multi-pixel SIS receivers. On the other hand, we also observed a periodical behavior in frequency dependence of the measured noise temperature and gain due to a standing-wave effect between the two SIS mixers, which is a problem to be solved.

Millimeter, Submillimeter, and Far-Infrared Detectors and Instrumentation for Astronomy XI•Dec 12, 2020•8 citations

Optimization and Validation of the Design of Superconductor-Insulator-Superconductor Mixer-Based Amplifier Circuits

Yoshinori Uzawa, Wenlei Shan, Akira KAWAKAMI +5 more

We propose an optimization method for a superconductor-insulator-superconductor (SIS) mixer-based amplifier circuit that employs SIS up- and down-converters. Such a novel amplifier configuration could enable superior low-noise performance for future broadband amplifier systems, such as those for large arrays of superconducting sensors or qubits. Optimization was achieved by identifying a solution in which the mutually dependent impedances of the SIS mixers converge under given conditions. A circuit design using this method predicted an amplifier gain of approximately 20 dB and a noise temperature of approximately 2 K at 4 K operation when practical current-voltage characteristics of Nb SIS junctions are used in the simulation. To verify the validity of this method, an amplifier circuit was prepared using waveguide Nb/AlOx/Nb mixer modules. By varying the phase delay between the two SIS mixers, changes in gain were observed, resulting from different convergence conditions of their mutually dependent impedances, which closely matched the predictions made using this method. These results are promising for the development of an integrated circuit including SIS amplifiers and superconducting detector arrays, with bandwidths of 10 GHz or above. This may also enable novel nonreciprocal microwave circuits such as gyrators, isolators, and circulators.

IEEE Transactions on Applied Superconductivity•Dec 23, 2025•0 citations

Study on Frequency Up-Conversion Characteristic in SIS Mixers and its Application

雄人 上月

Superconductor-insulator-superconductor (SIS) junctions, which are low-noise heterodyne mixers, have been used as frequency converters.In recent years, ultralow power consumption of receiver components has become essential to increase the scale and integration of receiver systems.In this paper, we explore the performance of SIS mixers, which have been widely used as a low-noise frequency down-converter in the field of radio astronomy, as a frequency up-converter and discuss the possibility of its application to low-noise microwave amplifiers with ultra-low power consumption.In this study, we investigate the characteristics of the SIS upconverters, clarifying the conditions for gain generation in up-conversion.This research will lead to the realization of ultra-low-power amplifiers based on SIS mixers, which will solve the problem of increasing power consumption in future receiver systems.Chapter 1 describes the background of the research, including the ongoing problem of the increasing scale of receiving systems and the associated power consumption of low-noise amplifiers in the field of high-sensitivity reception, the history of the research on heterodyne mixing using SIS mixers, and the significance and policy of the research.Chapter 2 describes the theoretical background relevant to this study and discusses the basic properties of SIS junctions as heterodyne mixers.In Chapter 3, we describe the numerical analysis conducted to clarify the upconversion characteristics of the SIS mixer.In Chapter 4, we describe the mixing characteristics of SIS junctions at 40 GHz by constructing a new experimental system that directly measures the characteristics of heterodyne mixers. IVIn Chapter 5, a new experimental system is constructed using an existing SIS mixer developed as a down-converter for W-band, and the up-conversion gain characteristics in the 100 GHz band are described.Chapter 6 describes a demonstration experiment that shows the potential of the SIS mixer to be applied to ultra-low-power low-noise microwave amplifiers.Chapter 7 summarizes the paper and discusses the challenges and prospects for future realization and application of ultra-low-power amplifiers.V

•Mar 24, 2022•0 citations

Low-Noise Superconducting Mixers for the Terahertz Frequency Range

Victor Y. Belitsky, Serguei Cherednichenko, Dag Winkler

This chapter discusses the high sensitivity superconducting mixers, i.e. detectors used in heterodyne receivers. Today, there are essentially two very successful concepts of superconducting mixers, or frequency down-converters, the superconductor-insulator-superconductor tunnel junction SIS mixer and the superconducting hot-electron bolometer mixer. Moving up to higher frequencies in the microwave and millimeter wave electromagnetic spectra makes it more and more difficult to retrieve a good signal-to-noise ratio with ordinary solid-state amplifiers. The driving force for using superconducting mixers is their excellent down-conversion efficiency and capability to down-convert RF signals from microwave frequencies up to the terahertz region. The main purpose of a receiver is to pick up and amplify a weak signal, which can then be accurately determined in amplitude and phase. The mixer noise temperature and conversion gain are the most important parameters for the mixing device. The Josephson junction mixer was one of the first suggested devices based on superconducting point contacts and later tunnel junctions.

CRC Press eBooks•May 17, 2022•1 citation
This paper describes a low-noise microwave amplifier based on up- and down-frequency-conversion processes in quasiparticle superconductor–insulator–superconductor (SIS) tunnel junctions. The SIS amplifier was configured with two SIS frequency-converter modules and a cryogenic millimeter-wave isolator inserted between them. Moreover, a local oscillator (LO) using millimeter-wave attenuators and a phase shifter was considered. This setup allowed the control of individual LO power and differential phase in these SIS frequency converters to optimize the amplifier performance. The SIS amplifier showed noise temperatures as low as 11 K and a 6–8 dB gain from nearly DC to 5 GHz. The attained microwave performance is promising for obtaining large-format arrays, such as multibeam heterodyne receivers. Moreover, this two-frequency-converter concept based on SIS junctions might enable microwave applications, such as wideband non-reciprocal circuits in isolators, gyrators, and circulators, which are essential devices in the quantum computing and radio astronomy fields.
Heterodyne instruments have recently attained quantum-limited low-noise performance, particularly in radio astronomy, but it is difficult to develop large heterodyne arrays such as a modern radio camera using cryogenic sensitive detectors based on microwave kinetic inductance detectors, transition edge sensors, etc. In the realization of the heterodyne array, the reduction of power dissipation for semiconductor-based amplifiers remains a major challenge. Alternatively, superconducting parametric amplifiers still seem to have several barriers to application, especially in terms of operating temperature. Here, we show a novel concept of microwave amplification based on up and down frequency-conversion processes using quasiparticle superconductor-insulator-superconductor (SIS) tunnel junctions. We demonstrate positive gain using a proof-of-concept test module, which operates with a power dissipation of several μW at a bath temperature of 4 K. The performance of the module suggests great potential for application in large arrays.
We propose a low-noise and low-power-consumption microwave amplifier using superconductor-insulator-superconductor (SIS) mixers as quasi-particle frequency up- and down-converters pumped by a Josephson array oscillator in the millimeter-wave band. A proof-of-concept study of an amplifier with two W-band waveguide mixers using Nb/Al-AlOx/Nb junctions in a cascade connection demonstrated an average gain of 6 dB and a noise temperature of 12 K from nearly DC to 5 GHz. We also designed and fabricated a Josephson array oscillator at 100 GHz, which consisted of 31 overdamped Josephson junctions placed at each half-wavelength in an Nb microstrip line. The estimated output power of the oscillator was 0.2 μW at 100 GHz, which can be increased by increasing the number of the oscillator junctions. These results suggest that the proposed SIS mixer-based amplifier is suitable for on-chip integrated circuits to be implemented in large-scale multipixel SIS receivers and quantum computers.
We are investigating a possible microwave amplifier with low noise and low power consumption at cryogenic temperature for large scale multi-pixel heterodyne superconductor-insulator-superconductor (SIS) receivers at millimeter and submillimeter wavelengths. We propose the use of SIS junctions as amplifier elements based on quasi-particle mixing. By connecting an SIS up-converter and an SIS down-converter in series with gain in both converters, a lownoise and low-power-consumption high-frequency amplifier can be obtained in principle. A proof-of-concept study has been made by configuring an amplifier with two Nb/Al-AlOx/Nb mixers in the 150-GHz band in a standard noise and gain measurement setup at 4 K with a microwave noise source as an input signal. We observed a maximum gain of more than 10 dB and a minimum noise temperature of less than 10 K, which suggests that our proposed SIS amplifier is capable for multi-pixel SIS receivers. On the other hand, we also observed a periodical behavior in frequency dependence of the measured noise temperature and gain due to a standing-wave effect between the two SIS mixers, which is a problem to be solved.
We propose an optimization method for a superconductor-insulator-superconductor (SIS) mixer-based amplifier circuit that employs SIS up- and down-converters. Such a novel amplifier configuration could enable superior low-noise performance for future broadband amplifier systems, such as those for large arrays of superconducting sensors or qubits. Optimization was achieved by identifying a solution in which the mutually dependent impedances of the SIS mixers converge under given conditions. A circuit design using this method predicted an amplifier gain of approximately 20 dB and a noise temperature of approximately 2 K at 4 K operation when practical current-voltage characteristics of Nb SIS junctions are used in the simulation. To verify the validity of this method, an amplifier circuit was prepared using waveguide Nb/AlOx/Nb mixer modules. By varying the phase delay between the two SIS mixers, changes in gain were observed, resulting from different convergence conditions of their mutually dependent impedances, which closely matched the predictions made using this method. These results are promising for the development of an integrated circuit including SIS amplifiers and superconducting detector arrays, with bandwidths of 10 GHz or above. This may also enable novel nonreciprocal microwave circuits such as gyrators, isolators, and circulators.
Superconductor-insulator-superconductor (SIS) junctions, which are low-noise heterodyne mixers, have been used as frequency converters.In recent years, ultralow power consumption of receiver components has become essential to increase the scale and integration of receiver systems.In this paper, we explore the performance of SIS mixers, which have been widely used as a low-noise frequency down-converter in the field of radio astronomy, as a frequency up-converter and discuss the possibility of its application to low-noise microwave amplifiers with ultra-low power consumption.In this study, we investigate the characteristics of the SIS upconverters, clarifying the conditions for gain generation in up-conversion.This research will lead to the realization of ultra-low-power amplifiers based on SIS mixers, which will solve the problem of increasing power consumption in future receiver systems.Chapter 1 describes the background of the research, including the ongoing problem of the increasing scale of receiving systems and the associated power consumption of low-noise amplifiers in the field of high-sensitivity reception, the history of the research on heterodyne mixing using SIS mixers, and the significance and policy of the research.Chapter 2 describes the theoretical background relevant to this study and discusses the basic properties of SIS junctions as heterodyne mixers.In Chapter 3, we describe the numerical analysis conducted to clarify the upconversion characteristics of the SIS mixer.In Chapter 4, we describe the mixing characteristics of SIS junctions at 40 GHz by constructing a new experimental system that directly measures the characteristics of heterodyne mixers. IVIn Chapter 5, a new experimental system is constructed using an existing SIS mixer developed as a down-converter for W-band, and the up-conversion gain characteristics in the 100 GHz band are described.Chapter 6 describes a demonstration experiment that shows the potential of the SIS mixer to be applied to ultra-low-power low-noise microwave amplifiers.Chapter 7 summarizes the paper and discusses the challenges and prospects for future realization and application of ultra-low-power amplifiers.V
This chapter discusses the high sensitivity superconducting mixers, i.e. detectors used in heterodyne receivers. Today, there are essentially two very successful concepts of superconducting mixers, or frequency down-converters, the superconductor-insulator-superconductor tunnel junction SIS mixer and the superconducting hot-electron bolometer mixer. Moving up to higher frequencies in the microwave and millimeter wave electromagnetic spectra makes it more and more difficult to retrieve a good signal-to-noise ratio with ordinary solid-state amplifiers. The driving force for using superconducting mixers is their excellent down-conversion efficiency and capability to down-convert RF signals from microwave frequencies up to the terahertz region. The main purpose of a receiver is to pick up and amplify a weak signal, which can then be accurately determined in amplitude and phase. The mixer noise temperature and conversion gain are the most important parameters for the mixing device. The Josephson junction mixer was one of the first suggested devices based on superconducting point contacts and later tunnel junctions.