Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Serial Biasing Technique for Electronic Design Automation in RSFQ Circuits

Ashish Shukla, Timur V. Filippov, Dmitri E. Kirichenko, Sukanya Sagarika Meher, M. Celik, Mingoo Seok, Deepnarayan Gupta

Published Oct 14, 2022• 4 citations
Publisher

Abstract

There has been renewed interest and efforts in increasing the complexity of superconductor circuits by means of electronic design automation (EDA). Serial biasing (SB) is a technique that reduces the total dc bias current required by large rapid single flux quantum (RSFQ) circuits, including its energy-efficient variant, ERSFQ. We believe SB needs to be incorporated in any EDA flow for large circuits. In SB, equally biased circuit blocks are placed on galvanically isolated islands and biased in series. SFQ pulses are transferred between islands by means of driver-receiver pairs (DRPs). The special current management technique, called the grapevine (GV) approach and introduced earlier, is used to handle the bias current flowing in and out of an island. In this article, we present all required layout primitives needed to implement SB for the IARPA-led SuperTools cell library that targets the SFQ5ee fab node at MIT Lincoln Laboratory. We discuss the horizontal and vertical composite driver-receiver pairs that comprise not only DRPs but also transmitters and receivers for passive transmission lines. We present the basic blocks to implement the GV managing technique for current injection and extraction. As a proof of concept, we designed a four-island test circuit that comprises all discussed layout primitives and employs an on-chip pseudorandom binary sequence generator as a test pattern source. The test circuit worked up to 50 GHz at the BER level of 10−12. We discuss future steps to improve the SB technique.

DOI
10.1109/tasc.2022.3214767

Related papers

60-GHz Single Flux Quantum Pulse Transfer Circuit for Serial Biasing

Ashish Shukla, Dmitri E. Kirichenko, Timur V. Filippov +4 more

Serial Biasing (SB) is a technique to reduce the total DC bias current of Rapid Single Flux Quantum (RSFQ) circuits by partitioning a design into several islands with isolated grounds and sequential biasing. In this paper we focus on the design of a driver-receiver pair (DRP) to transfer pulses between islands that are galvanically isolated for pulse streams. We discuss both DRP itself and the structure for its testing, that comprises several DRPs connected in series, on-chip pseudo random binary sequence (PRBS) generator for circuit stimulation, and HF output interface. We use the layout of DRPs’ chain as an example to illustrate the advantage of the grapevine (GV) approach, introduced earlier, to manage the bias current flowing into and out of an island. The GV current management technique is analyzed by both electromagnetic simulations and measurement, compared, and contrasted with the so-called ‘straightforward’ (SF) approach. The maximum operational frequency for SF test structure was 10 GHz with zero margins for the SB current. Measurements of the GV structure at 10 GHz demonstrated BER of 10−12with ±5.8% margins for SB current. We observed the correct operation of the 5-island DRP chain up to 60 GHz using the grapevine approach for SB current management. All chips were fabricated at MIT Lincoln Laboratory using SFQ5ee fab node.

IEEE Transactions on Applied Superconductivity•Jan 23, 2023•5 citations

Pulse Interfaces and Current Management Techniques for Serially Biased RSFQ Circuits

Ashish Shukla, Dmitri E. Kirichenko, Timur V. Filippov +4 more

As digital superconductor circuits based on Rapid Single Flux Quantum (RSFQ) logic scale up in complexity, so does the total current required to provide dc bias. Serial biasing (SB) is a promising solution that can be used to reduce the current by placing identical digital blocks on islands with isolated grounds and bias them sequentially. There are typically two implementations that are essential for the SB approach: the design of a driver-receiver pair (DRP) for inter-island pulse transport and the current management technique to handle the bias current flowing into and out of an island. While a DRP with good fidelity is essential for any serially biased circuit, the current management becomes critical for designs with relatively large bias current. In this paper, we address the latter. First, we propose a grapevine biasing scheme for serial bias current management. Second, we implement the technique using two exemplar circuits: the parallel counter and the digital decimation filter. We report the low and high speed test results up to 50 GHz for both circuits fabricated at MIT-LL in the SFQ5ee 10 kA/2 Ω fab node.

IEEE Transactions on Applied Superconductivity•Jan 13, 2022•9 citations

Serially Biased Components for Digital-RF Receiver

Timur V. Filippov, Anubhav Sahu, Saad M. Sarwana +2 more

Reduction of total bias current using the serial biasing technique is required for RSFQ-based digital-RF receiver realization. This will have a major impact on reducing the size, weight and power consumption of the complete cryocooled receiver system. The approach is based on partitioning a homogeneous design into several isolated islands biased in series and transmitting SFQ pulses between islands, over moats through inductively-coupled driver-receiver-pairs (DRPs). Experimental data on testing of 100 DRPs connected in series are reported and bit-error-rate estimates are given. Our goal is to serially bias two sets of homogeneous circuit blocks in the digital-RF receiver design: (1) digital decimation filter (DDF) bit slices, and (2) output drivers. The correct operation of test chips containing four bit-slices of a second-order DDF, partitioned into 2 and 4 islands, are demonstrated. Results of 8 output drivers, serially biased on 2, 4, and 8 islands, are reported. Design issues of scaling to a digital-RF receiver, containing 18-20 DDF bit slices and 16 output drivers are discussed.

IEEE Transactions on Applied Superconductivity•Jun 1, 2009•26 citations

Current Recycling: New Results

Vasili K. Semenov, Yuri A. Polyakov

Long ago, current recycling or serial biasing technique was recognized as a promising solution for the reduction of bias current in VLSI dc biased digital superconductor circuits. Despite a significant number of declarations, not so many successful experiments have been reported so far. In the paper we discuss our recent experiments with serially biased 16-bit counter-flow RSFQ shift registers, connected by special interfaces that are able to transfer SFQ pulses between the galvanically isolated driver and receiver. The required functionality is achieved using a superconductor transformer with isolated input and output coils. The known drawback of such interfaces is their parasitic sensitivity to magnetic fields induced by remote currents. To depress this sensitivity we have implemented a special superconductor guard that uses six superconductor layers. We have achieved stable operations of such registers with 16 current recycling stacks. The circuits have been fabricated at MIT Lincoln Laboratory.

IEEE Transactions on Applied Superconductivity•Mar 18, 2019•16 citations

The development and characterisation of a parameterised RSFQ cell library for layout synthesis

Lieze Schindler

ENGLISH ABSTRACT: Superconductor electronics have shown great promise for interfacing quantum computers to conventional electronics. Several superconductor logic families show potential, \nbut one particular logic family has shown reliable results: Rapid Single Flux Quantum \n(RSFQ). RSFQ logic implements single SFQ pulses to represent binary data instead of \nthe traditional voltage levels used by semiconductor electronics. RSFQ is so ubiquitous \nto superconductor digital systems that it serves as the entry to superconductor digital \ndesign. Presently, however, the field of RSFQ logic cell design is very exclusive with \na small number of physicists and engineers able to design efficient RSFQ cells. This \nresearch aims to provide a formalised RSFQ design methodology with education quality \ncircuit theory. Several RSFQ examples are designed, analysed and improved using phasebased circuit equations. Similar to Kirchhoff’s current and voltage laws, these phase-based \nequations can be used to accurately determine the current distribution within a cell. The \ndesign methodology for multi-state RSFQ cells is also discussed. Multiple simulation \nmethods confirming cell functionality and operating margins are also presented. The \neducation regarding the design, analysis and implementation of RSFQ cells is vastly \nexpanded through this research which can accelerate the field of quantum circuit design. \nRSFQ cells can be connected using a non-storing inductive loop, Josephson transmission lines (JTLs) or, alternatively, superconductor passive transmission lines (PTLs) \nto bridge longer distances. Signal transmission of SFQ pulses through PTLs and JTLs \nare analysed and compared. Impedance matching for PTL interconnects to reduce pulse \nreflection is also investigated. \nAn example of a portable RSFQ cell library for layout synthesis is developed as \npart of the IARPA SuperTools program. The challenges of RSFQ cell layouts for the \nMassachusetts Institute of Technology Lincoln Laboratory (MIT-LL) SFQ5ee fabrication \nprocess are discussed. A methodology for establishing a standardised cell layout synthesis \nis presented. The research contributes to the design and characterisation of track routing \narchitecture for RSFQ on a multilayer fabrication process. \nLastly, methods to test fabricated RSFQ circuits are presented. This includes testing \nthe functionality of individual cells, as well as measuring throughput delays. As the SFQ \npulses are only a few picoseconds wide, it is not possible to observe these pulses using \nconventional measuring equipment. The fabricated tests must therefore be designed in \nsuch a way that it is possible to extract meaningful measurements.

•Mar 1, 2021•3 citations

Current Recycling in Heterogeneous RSFQ Circuits

Tejumadejesu Oluwadamilare, Eby G. Friedman

As single flux quantum (SFQ) circuit complexities scale, larger bias currents are required. The large current produces excessive heat and greatly complicates the design process. Current recycling offers a solution by reducing the required bias current through serially biased circuit blocks. Serial biasing is typically achieved in homogeneous SFQ systems where similar bias currents are required in similar circuits. Each of these homogeneous circuits is often placed on different ground planes and serially biased to reuse the bias currents. To address heterogeneous circuits with varying bias current requirements, a novel serial biasing technique is proposed. An interface between the ground planes with unequal bias current is presented that exhibits a current balancing capability. The interface supplies additional current before passing the current to the next ground plane. The ground planes are arranged in ascending order of bias current to manage the complexity of these heterogeneous circuits. Using a one bit SFQ full adder as an example, the proposed approach demonstrates several key benefits: a 49% reduction in the number of driver-receiver pairs, a 6.5% reduction in power dissipation, and a 35% reduction in bias current across a heterogeneous SFQ circuit placed on three isolated ground planes. The performance, bias current margins, and methods for current reduction are also discussed, showcasing the effectiveness of current recycling in improving the efficiency of complex heterogeneous SFQ systems.

IEEE Transactions on Applied Superconductivity•Jan 16, 2025•2 citations
There has been renewed interest and efforts in increasing the complexity of superconductor circuits by means of electronic design automation (EDA). Serial biasing (SB) is a technique that reduces the total dc bias current required by large rapid single flux quantum (RSFQ) circuits, including its energy-efficient variant, ERSFQ. We believe SB needs to be incorporated in any EDA flow for large circuits. In SB, equally biased circuit blocks are placed on galvanically isolated islands and biased in series. SFQ pulses are transferred between islands by means of driver-receiver pairs (DRPs). The special current management technique, called the grapevine (GV) approach and introduced earlier, is used to handle the bias current flowing in and out of an island. In this article, we present all required layout primitives needed to implement SB for the IARPA-led SuperTools cell library that targets the SFQ5ee fab node at MIT Lincoln Laboratory. We discuss the horizontal and vertical composite driver-receiver pairs that comprise not only DRPs but also transmitters and receivers for passive transmission lines. We present the basic blocks to implement the GV managing technique for current injection and extraction. As a proof of concept, we designed a four-island test circuit that comprises all discussed layout primitives and employs an on-chip pseudorandom binary sequence generator as a test pattern source. The test circuit worked up to 50 GHz at the BER level of 10−12. We discuss future steps to improve the SB technique.
Serial Biasing (SB) is a technique to reduce the total DC bias current of Rapid Single Flux Quantum (RSFQ) circuits by partitioning a design into several islands with isolated grounds and sequential biasing. In this paper we focus on the design of a driver-receiver pair (DRP) to transfer pulses between islands that are galvanically isolated for pulse streams. We discuss both DRP itself and the structure for its testing, that comprises several DRPs connected in series, on-chip pseudo random binary sequence (PRBS) generator for circuit stimulation, and HF output interface. We use the layout of DRPs’ chain as an example to illustrate the advantage of the grapevine (GV) approach, introduced earlier, to manage the bias current flowing into and out of an island. The GV current management technique is analyzed by both electromagnetic simulations and measurement, compared, and contrasted with the so-called ‘straightforward’ (SF) approach. The maximum operational frequency for SF test structure was 10 GHz with zero margins for the SB current. Measurements of the GV structure at 10 GHz demonstrated BER of 10−12with ±5.8% margins for SB current. We observed the correct operation of the 5-island DRP chain up to 60 GHz using the grapevine approach for SB current management. All chips were fabricated at MIT Lincoln Laboratory using SFQ5ee fab node.
As digital superconductor circuits based on Rapid Single Flux Quantum (RSFQ) logic scale up in complexity, so does the total current required to provide dc bias. Serial biasing (SB) is a promising solution that can be used to reduce the current by placing identical digital blocks on islands with isolated grounds and bias them sequentially. There are typically two implementations that are essential for the SB approach: the design of a driver-receiver pair (DRP) for inter-island pulse transport and the current management technique to handle the bias current flowing into and out of an island. While a DRP with good fidelity is essential for any serially biased circuit, the current management becomes critical for designs with relatively large bias current. In this paper, we address the latter. First, we propose a grapevine biasing scheme for serial bias current management. Second, we implement the technique using two exemplar circuits: the parallel counter and the digital decimation filter. We report the low and high speed test results up to 50 GHz for both circuits fabricated at MIT-LL in the SFQ5ee 10 kA/2 Ω fab node.
Reduction of total bias current using the serial biasing technique is required for RSFQ-based digital-RF receiver realization. This will have a major impact on reducing the size, weight and power consumption of the complete cryocooled receiver system. The approach is based on partitioning a homogeneous design into several isolated islands biased in series and transmitting SFQ pulses between islands, over moats through inductively-coupled driver-receiver-pairs (DRPs). Experimental data on testing of 100 DRPs connected in series are reported and bit-error-rate estimates are given. Our goal is to serially bias two sets of homogeneous circuit blocks in the digital-RF receiver design: (1) digital decimation filter (DDF) bit slices, and (2) output drivers. The correct operation of test chips containing four bit-slices of a second-order DDF, partitioned into 2 and 4 islands, are demonstrated. Results of 8 output drivers, serially biased on 2, 4, and 8 islands, are reported. Design issues of scaling to a digital-RF receiver, containing 18-20 DDF bit slices and 16 output drivers are discussed.
Long ago, current recycling or serial biasing technique was recognized as a promising solution for the reduction of bias current in VLSI dc biased digital superconductor circuits. Despite a significant number of declarations, not so many successful experiments have been reported so far. In the paper we discuss our recent experiments with serially biased 16-bit counter-flow RSFQ shift registers, connected by special interfaces that are able to transfer SFQ pulses between the galvanically isolated driver and receiver. The required functionality is achieved using a superconductor transformer with isolated input and output coils. The known drawback of such interfaces is their parasitic sensitivity to magnetic fields induced by remote currents. To depress this sensitivity we have implemented a special superconductor guard that uses six superconductor layers. We have achieved stable operations of such registers with 16 current recycling stacks. The circuits have been fabricated at MIT Lincoln Laboratory.
ENGLISH ABSTRACT: Superconductor electronics have shown great promise for interfacing quantum computers to conventional electronics. Several superconductor logic families show potential, \nbut one particular logic family has shown reliable results: Rapid Single Flux Quantum \n(RSFQ). RSFQ logic implements single SFQ pulses to represent binary data instead of \nthe traditional voltage levels used by semiconductor electronics. RSFQ is so ubiquitous \nto superconductor digital systems that it serves as the entry to superconductor digital \ndesign. Presently, however, the field of RSFQ logic cell design is very exclusive with \na small number of physicists and engineers able to design efficient RSFQ cells. This \nresearch aims to provide a formalised RSFQ design methodology with education quality \ncircuit theory. Several RSFQ examples are designed, analysed and improved using phasebased circuit equations. Similar to Kirchhoff’s current and voltage laws, these phase-based \nequations can be used to accurately determine the current distribution within a cell. The \ndesign methodology for multi-state RSFQ cells is also discussed. Multiple simulation \nmethods confirming cell functionality and operating margins are also presented. The \neducation regarding the design, analysis and implementation of RSFQ cells is vastly \nexpanded through this research which can accelerate the field of quantum circuit design. \nRSFQ cells can be connected using a non-storing inductive loop, Josephson transmission lines (JTLs) or, alternatively, superconductor passive transmission lines (PTLs) \nto bridge longer distances. Signal transmission of SFQ pulses through PTLs and JTLs \nare analysed and compared. Impedance matching for PTL interconnects to reduce pulse \nreflection is also investigated. \nAn example of a portable RSFQ cell library for layout synthesis is developed as \npart of the IARPA SuperTools program. The challenges of RSFQ cell layouts for the \nMassachusetts Institute of Technology Lincoln Laboratory (MIT-LL) SFQ5ee fabrication \nprocess are discussed. A methodology for establishing a standardised cell layout synthesis \nis presented. The research contributes to the design and characterisation of track routing \narchitecture for RSFQ on a multilayer fabrication process. \nLastly, methods to test fabricated RSFQ circuits are presented. This includes testing \nthe functionality of individual cells, as well as measuring throughput delays. As the SFQ \npulses are only a few picoseconds wide, it is not possible to observe these pulses using \nconventional measuring equipment. The fabricated tests must therefore be designed in \nsuch a way that it is possible to extract meaningful measurements.
As single flux quantum (SFQ) circuit complexities scale, larger bias currents are required. The large current produces excessive heat and greatly complicates the design process. Current recycling offers a solution by reducing the required bias current through serially biased circuit blocks. Serial biasing is typically achieved in homogeneous SFQ systems where similar bias currents are required in similar circuits. Each of these homogeneous circuits is often placed on different ground planes and serially biased to reuse the bias currents. To address heterogeneous circuits with varying bias current requirements, a novel serial biasing technique is proposed. An interface between the ground planes with unequal bias current is presented that exhibits a current balancing capability. The interface supplies additional current before passing the current to the next ground plane. The ground planes are arranged in ascending order of bias current to manage the complexity of these heterogeneous circuits. Using a one bit SFQ full adder as an example, the proposed approach demonstrates several key benefits: a 49% reduction in the number of driver-receiver pairs, a 6.5% reduction in power dissipation, and a 35% reduction in bias current across a heterogeneous SFQ circuit placed on three isolated ground planes. The performance, bias current margins, and methods for current reduction are also discussed, showcasing the effectiveness of current recycling in improving the efficiency of complex heterogeneous SFQ systems.