Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Physical Review A

Optimizing the coupling efficiency of spontaneous parametric down-conversion photon pairs into single-mode fibers

Nicolas Schwaller, Geobae Park, Ryo Okamoto, Shigeki Takeuchi

Published Oct 28, 2022• 9 citations
Publisher

Abstract

Both correlated-mode coupling efficiency and photon pair flux (brightness) of spontaneous parametric down-conversion (SPDC) coupled into single-mode fibers are key parameters for various quantum information science applications. We present an experimental investigation on the optimization of the correlated-mode coupling efficiency and the brightness of frequency-degenerated SPDC photon pairs into single-mode optical fibers. Using photon pairs generated from a type-I phase-matched bulk $\ensuremath{\beta}$-barium borate crystal pumped by a continuous-wave laser, we carefully evaluated both the correlated-mode coupling efficiency and the brightness of SPDC light coupled to a single-mode optical fiber, while continuously changing the focusing of the pump and collection modes, experimenting with Rayleigh lengths from 3 to 280 (for the pump) and 0.2 to 20 (for the collection) times the crystal length. The measured data suggest that the correlated-mode coupling efficiency can be close to unity for any pump focus, however, the optimal Rayleigh length of the collection mode depends on the pump focus parameter, and the brightness can be increased by tightening the pump focus, provided that the Rayleigh length of the collection mode is precisely adjusted. A maximal correlated-mode coupling efficiency of $99.0\ifmmode\pm\else\textpm\fi{}1.3%$ was experimentally achieved. These results will be useful for photonic quantum science and technology using SPDC sources with high heralding efficiencies.

DOI
10.1103/physreva.106.043719

Related papers

Optimal focusing for maximal collection of entangled narrow-band photon pairs into single-mode fibers

Daniel Ljunggren, Maria Tengner

We present a theoretical and experimental investigation of the emission characteristics and the flux of photon pairs generated by spontaneous parametric downconversion in quasi-phase matched bulk crystals for the use in quantum communication sources. We show that, by careful design, one can attain well defined modes close to the fundamental mode of optical fibers and obtain high coupling efficiencies also for bulk crystals, these being more easily aligned than crystal waveguides. We distinguish between singles coupling, ${\ensuremath{\gamma}}_{\mathrm{s}}$ and ${\ensuremath{\gamma}}_{\mathrm{i}}$, conditional coincidence, ${\ensuremath{\mu}}_{\mathrm{i}\ensuremath{\mid}\mathrm{s}}$, and pair coupling, ${\ensuremath{\gamma}}_{\mathrm{c}}$, and show how each of these parameters can be maximized by varying the focusing of the pump mode and the fiber-matched modes using standard optical elements. Specifically we analyze a periodically poled KTP-crystal pumped by a $532\phantom{\rule{0.3em}{0ex}}\mathrm{nm}$ laser creating photon pairs at $810\phantom{\rule{0.3em}{0ex}}\mathrm{nm}$ and $1550\phantom{\rule{0.3em}{0ex}}\mathrm{nm}$. Numerical calculations lead to coupling efficiencies above 93% at optimal focusing, which is found by the geometrical relation $L∕{z}_{R}$ to be $\ensuremath{\approx}1$ to 2 for the pump mode and $\ensuremath{\approx}2$ to 3 for the fiber-modes, where $L$ is the crystal length and ${z}_{R}$ is the Rayleigh-range of the mode-profile. These results are independent on $L$. By showing that the single-mode bandwidth decreases $\ensuremath{\propto}1∕L$, we can therefore design the source to produce and couple narrow bandwidth photon pairs well into the fibers. Smaller bandwidth means both less chromatic dispersion for long propagation distances in fibers, and that telecom Bragg gratings can be utilized to compensate for broadened photon packets---a vital problem for time-multiplexed qubits. Longer crystals also yield an increase in fiber photon flux $\ensuremath{\propto}\sqrt{L}$, and so, assuming correct focusing, we can only see advantages using long crystals.

arXiv:quant-ph/0507046•Physical Review A•Dec 2, 2005•107 citations

Towards ultrabright photon pair sources for quantum communication (Conference Presentation)

Rana Sebak, Emma Brambila, Tobias Bernd Gäbler +3 more

Entangled photon pairs play a crucial role in emerging quantum technologies, acting as tamper-proof padlocks in secure quantum communication, ultra-precise probes in quantum metrology and high-fidelity information carriers in photonic quantum computing. Amongst the many technological possibilities for generating photon pairs, sources based on spontaneous parametric down-conversion (SPDC) in second-order nonlinear crystals are still the workhorse tool in quantum optics laboratories, and more recently even in long-distance quantum communication with satellites. SPDC is a widely used method to create entangled photon pairs. The number of photon pairs that can be detected in a particular choice of collection modes, typically being optical single-mode fibers, depends critically on the spatial characteristics of the multi-mode SPDC emission as well as the particular beam waist of the collection modes. While several studies have already addressed the issue of optimal fiber coupling of SPDC photons in theory and experiment, the results of these studies arrive at different conclusions. Here, we present the results of a comprehensive experimental study on the optimal collection of photon pairs into single-mode optical fibers. Our approach is based on quasi-phase-matched type II SPDC from a periodically poled KTiOPO4 (ppKTP) crystal. We discuss the influence of pump and collection focal parameters on the spectral brightness and heralding efficiency, as well as practical issues of alignment tolerances into an optical single mode fiber. Further, Using two-photon interference (Hong-Ou-Mandel interference), we assess the spectral bandwidth of the photon pairs for variable crystal lengths. The results are in good agreement with our theoretical model, thus providing the recipe of building ultra bright and stable entangled photon sources.

SPIE Quantum Technologies•Mar 30, 2020•0 citations

Optimizing focused pump beam characteristics for maximum correlated photon pairs in non-collinear degenerate parametric down conversion

Ali Anwar, Nijil Lal, P. Chithrabhanu +3 more

We investigate the methods to obtain maximum correlated photon pairs generated in Type I spontaneous parametric down conversion (SPDC) with focused pump beam. We study the effect of pump focusing on the photon collection efficiency of signal and idler modes. The correlated photon pair collection efficiency decreases asymptotically with input pump beam focusing parameter [1]. The results obtained here are expected to be useful in designing appropriate optical fibers for generating efficient entangled photon sources for quantum information applications.

Workshop on Recent Advances in Photonics (WRAP)•Dec 1, 2015•0 citations

Optimal focusing conditions for bright spontaneous parametric down-conversion sources

Lorenzo Coccia, Alberto Santamato, Giuseppe Vallone +1 more

Optimizing the brightness of a spontaneous parametric down-conversion (SPDC) source is an important task for many quantum information applications. We investigate the optimal focusing conditions to maximize the number of photons produced in an SPDC process and coupled with single-mode fibers. We provide a general expression for the two-photon wave function, generalizing previous known results, by considering collinear and noncollinear emission. We present analytical expressions for our results in the thin-crystal limit and clarify the relation between different focusing conditions already existing in the literature. Differently from what was previously reported, we show that the optimal ratio between the pump waist and the generated photons waist depends on the emission angle: It is $1/\sqrt{2}$ for collinear degenerate emission and approaches $1/2$ for larger collection angles. The role of spectral filters is also analyzed. We support and enrich our discussion with numerical simulations, performed for type-I SPDC in a $\ensuremath{\beta}$ barium borate crystal. For this type of emission, we also investigate the role of the transverse walk-off outside the thin-crystal regime.

arXiv:2302.01118•Physical Review A•Jun 28, 2023•12 citations

Gaussian mode coupling of spectrally broadband photons from bulk spontaneous parametric down-conversion: A spatial-spectral mode analysis of fiber coupling

Carlos Sevilla-Gutiérrez, Varun Raj Kaipalath, Fabian Steinlechner

Photon sources based on spontaneous parametric down-conversion (SPDC) are central to experimental quantum optics and quantum technologies. Their performance is commonly quantified by three metrics: pair-collection probability, heralding efficiency, and spectral purity. In bulk-crystal SPDC, these metrics are known to be mutually constrained, yet the physical origin of the resulting trade-offs is often obscured. We show that these trade-offs originate from the frequency-dependent population of discrete spatial modes in the SPDC emission. By performing a Laguerre-Gauss mode decomposition at each frequency component, we show how spectral-spatial non-separability impacts collection probability, heralding efficiency, and purity. We apply this framework to two widely used quasi-phase-matching configurations: collinear degenerate type-0 and type-II SPDC in periodically poled bulk crystals, and quantify how different phase-matching functions shape the spectral-spatial mode structure. In particular, for type-II SPDC we compare standard periodically poled and aperiodically poled Gaussian phase matching. We experimentally validate some of our theoretical results using spatial- and spectral-projection measurements. This spectral-spatial mode analysis provides a quantitative and predictive framework for understanding and engineering bulk-crystal photon sources, enabling systematic multi-parameter optimization beyond qualitative design guidelines.

quant-pharXiv:2602.23238•Physical Review A•Feb 27, 2026•1 citation

The analysis of photon pair source at telecom wavelength based on the BBO crystal (Conference Presentation)

Andrzej Gajewski, Piotr Leszek Kolenderski

There are several problems that must be solved in order to increase the distance of quantum communication protocols based on photons as an information carriers. One of them is the dispersion, whose effects can be minimized by engineering spectral properties of transmitted photons. In particular, it is expected that positively correlated photon pairs can be very useful. We present the full characterization of a source of single photon pairs at a telecom wavelength based on type II spontaneous parametric down conversion (SPDC) process in a beta-barium borate (BBO) crystal. In the type II process, a pump photon, which is polarized extraordinarily, splits in a nonlinear medium into signal and idler photons, which are polarized perpendicularly to each other. In order for the process to be efficient a phase matching condition must be fulfilled. These conditions originate from momentum and energy conservation rules and put severe restrictions on source parameters. Seemingly, these conditions force the photon pair to be negatively correlated in their spectral domain. However, it is possible to achieve positive correlation for pulsed pumping. The experimentally available degrees of freedom of a source are the width of the pumping beam, the collected modes’ widths, the length of the nonlinear crystal and the duration of the pumping pulse. In our numerical model we use the following figures of merit: the pair production rate, the efficiency of photon coupling into a single mode fiber, the spectral correlation of the coupled photon pair. The last one is defined as the Pearson correlation parameter for a joint spectral distribution. The aim here is to find the largest positive spectral correlation and the highest coupling efficiency. By resorting to the numerical model Ref. [1] we showed in Ref. [2], that by careful adjustment of the pump’s and the collected modes’ characteristics, one can optimize any of the source's parameters. Our numerical outcomes conform to the experimental results presented in Refs [3,4]. Here we investigate typical, experimentally available source parameters: the widths of the pump beam and collected modes ranging from 20μm to 500m, the crystal length ranging from 1mm to 7.5mm while the pulse duration is set to 50fs, 100fs or 150fs. We achieve the correlation coefficient value as high as approximately 0.8, or – for different values of parameters – coupling efficiency equal to 0.76.

•Dec 7, 2016•0 citations
Both correlated-mode coupling efficiency and photon pair flux (brightness) of spontaneous parametric down-conversion (SPDC) coupled into single-mode fibers are key parameters for various quantum information science applications. We present an experimental investigation on the optimization of the correlated-mode coupling efficiency and the brightness of frequency-degenerated SPDC photon pairs into single-mode optical fibers. Using photon pairs generated from a type-I phase-matched bulk \ensuremathβ\ensuremath{\beta}\ensuremathβ-barium borate crystal pumped by a continuous-wave laser, we carefully evaluated both the correlated-mode coupling efficiency and the brightness of SPDC light coupled to a single-mode optical fiber, while continuously changing the focusing of the pump and collection modes, experimenting with Rayleigh lengths from 3 to 280 (for the pump) and 0.2 to 20 (for the collection) times the crystal length. The measured data suggest that the correlated-mode coupling efficiency can be close to unity for any pump focus, however, the optimal Rayleigh length of the collection mode depends on the pump focus parameter, and the brightness can be increased by tightening the pump focus, provided that the Rayleigh length of the collection mode is precisely adjusted. A maximal correlated-mode coupling efficiency of 99.0\ifmmode±\else\textpm\fi1.399.0\ifmmode\pm\else\textpm\fi{}1.3%99.0\ifmmode±\else\textpm\fi1.3 was experimentally achieved. These results will be useful for photonic quantum science and technology using SPDC sources with high heralding efficiencies.
We present a theoretical and experimental investigation of the emission characteristics and the flux of photon pairs generated by spontaneous parametric downconversion in quasi-phase matched bulk crystals for the use in quantum communication sources. We show that, by careful design, one can attain well defined modes close to the fundamental mode of optical fibers and obtain high coupling efficiencies also for bulk crystals, these being more easily aligned than crystal waveguides. We distinguish between singles coupling, ${\ensuremath{\gamma}}_{\mathrm{s}}$ and ${\ensuremath{\gamma}}_{\mathrm{i}}$, conditional coincidence, ${\ensuremath{\mu}}_{\mathrm{i}\ensuremath{\mid}\mathrm{s}}$, and pair coupling, ${\ensuremath{\gamma}}_{\mathrm{c}}$, and show how each of these parameters can be maximized by varying the focusing of the pump mode and the fiber-matched modes using standard optical elements. Specifically we analyze a periodically poled KTP-crystal pumped by a 532nm532\phantom{\rule{0.3em}{0ex}}\mathrm{nm}532nm laser creating photon pairs at 810nm810\phantom{\rule{0.3em}{0ex}}\mathrm{nm}810nm and 1550nm1550\phantom{\rule{0.3em}{0ex}}\mathrm{nm}1550nm. Numerical calculations lead to coupling efficiencies above 93% at optimal focusing, which is found by the geometrical relation L∕zRL∕{z}_{R}L∕zR​ to be $\ensuremath{\approx}1$ to 2 for the pump mode and $\ensuremath{\approx}2$ to 3 for the fiber-modes, where LLL is the crystal length and zR{z}_{R}zR​ is the Rayleigh-range of the mode-profile. These results are independent on LLL. By showing that the single-mode bandwidth decreases $\ensuremath{\propto}1∕L$, we can therefore design the source to produce and couple narrow bandwidth photon pairs well into the fibers. Smaller bandwidth means both less chromatic dispersion for long propagation distances in fibers, and that telecom Bragg gratings can be utilized to compensate for broadened photon packets---a vital problem for time-multiplexed qubits. Longer crystals also yield an increase in fiber photon flux $\ensuremath{\propto}\sqrt{L}$, and so, assuming correct focusing, we can only see advantages using long crystals.
Entangled photon pairs play a crucial role in emerging quantum technologies, acting as tamper-proof padlocks in secure quantum communication, ultra-precise probes in quantum metrology and high-fidelity information carriers in photonic quantum computing. Amongst the many technological possibilities for generating photon pairs, sources based on spontaneous parametric down-conversion (SPDC) in second-order nonlinear crystals are still the workhorse tool in quantum optics laboratories, and more recently even in long-distance quantum communication with satellites. SPDC is a widely used method to create entangled photon pairs. The number of photon pairs that can be detected in a particular choice of collection modes, typically being optical single-mode fibers, depends critically on the spatial characteristics of the multi-mode SPDC emission as well as the particular beam waist of the collection modes. While several studies have already addressed the issue of optimal fiber coupling of SPDC photons in theory and experiment, the results of these studies arrive at different conclusions. Here, we present the results of a comprehensive experimental study on the optimal collection of photon pairs into single-mode optical fibers. Our approach is based on quasi-phase-matched type II SPDC from a periodically poled KTiOPO4 (ppKTP) crystal. We discuss the influence of pump and collection focal parameters on the spectral brightness and heralding efficiency, as well as practical issues of alignment tolerances into an optical single mode fiber. Further, Using two-photon interference (Hong-Ou-Mandel interference), we assess the spectral bandwidth of the photon pairs for variable crystal lengths. The results are in good agreement with our theoretical model, thus providing the recipe of building ultra bright and stable entangled photon sources.
We investigate the methods to obtain maximum correlated photon pairs generated in Type I spontaneous parametric down conversion (SPDC) with focused pump beam. We study the effect of pump focusing on the photon collection efficiency of signal and idler modes. The correlated photon pair collection efficiency decreases asymptotically with input pump beam focusing parameter [1]. The results obtained here are expected to be useful in designing appropriate optical fibers for generating efficient entangled photon sources for quantum information applications.
Optimizing the brightness of a spontaneous parametric down-conversion (SPDC) source is an important task for many quantum information applications. We investigate the optimal focusing conditions to maximize the number of photons produced in an SPDC process and coupled with single-mode fibers. We provide a general expression for the two-photon wave function, generalizing previous known results, by considering collinear and noncollinear emission. We present analytical expressions for our results in the thin-crystal limit and clarify the relation between different focusing conditions already existing in the literature. Differently from what was previously reported, we show that the optimal ratio between the pump waist and the generated photons waist depends on the emission angle: It is 1/21/\sqrt{2}1/2​ for collinear degenerate emission and approaches 1/21/21/2 for larger collection angles. The role of spectral filters is also analyzed. We support and enrich our discussion with numerical simulations, performed for type-I SPDC in a $\ensuremath{\beta}$ barium borate crystal. For this type of emission, we also investigate the role of the transverse walk-off outside the thin-crystal regime.
Photon sources based on spontaneous parametric down-conversion (SPDC) are central to experimental quantum optics and quantum technologies. Their performance is commonly quantified by three metrics: pair-collection probability, heralding efficiency, and spectral purity. In bulk-crystal SPDC, these metrics are known to be mutually constrained, yet the physical origin of the resulting trade-offs is often obscured. We show that these trade-offs originate from the frequency-dependent population of discrete spatial modes in the SPDC emission. By performing a Laguerre-Gauss mode decomposition at each frequency component, we show how spectral-spatial non-separability impacts collection probability, heralding efficiency, and purity. We apply this framework to two widely used quasi-phase-matching configurations: collinear degenerate type-0 and type-II SPDC in periodically poled bulk crystals, and quantify how different phase-matching functions shape the spectral-spatial mode structure. In particular, for type-II SPDC we compare standard periodically poled and aperiodically poled Gaussian phase matching. We experimentally validate some of our theoretical results using spatial- and spectral-projection measurements. This spectral-spatial mode analysis provides a quantitative and predictive framework for understanding and engineering bulk-crystal photon sources, enabling systematic multi-parameter optimization beyond qualitative design guidelines.
There are several problems that must be solved in order to increase the distance of quantum communication protocols based on photons as an information carriers. One of them is the dispersion, whose effects can be minimized by engineering spectral properties of transmitted photons. In particular, it is expected that positively correlated photon pairs can be very useful. We present the full characterization of a source of single photon pairs at a telecom wavelength based on type II spontaneous parametric down conversion (SPDC) process in a beta-barium borate (BBO) crystal. In the type II process, a pump photon, which is polarized extraordinarily, splits in a nonlinear medium into signal and idler photons, which are polarized perpendicularly to each other. In order for the process to be efficient a phase matching condition must be fulfilled. These conditions originate from momentum and energy conservation rules and put severe restrictions on source parameters. Seemingly, these conditions force the photon pair to be negatively correlated in their spectral domain. However, it is possible to achieve positive correlation for pulsed pumping. The experimentally available degrees of freedom of a source are the width of the pumping beam, the collected modes’ widths, the length of the nonlinear crystal and the duration of the pumping pulse. In our numerical model we use the following figures of merit: the pair production rate, the efficiency of photon coupling into a single mode fiber, the spectral correlation of the coupled photon pair. The last one is defined as the Pearson correlation parameter for a joint spectral distribution. The aim here is to find the largest positive spectral correlation and the highest coupling efficiency. By resorting to the numerical model Ref. [1] we showed in Ref. [2], that by careful adjustment of the pump’s and the collected modes’ characteristics, one can optimize any of the source's parameters. Our numerical outcomes conform to the experimental results presented in Refs [3,4]. Here we investigate typical, experimentally available source parameters: the widths of the pump beam and collected modes ranging from 20μm to 500m, the crystal length ranging from 1mm to 7.5mm while the pulse duration is set to 50fs, 100fs or 150fs. We achieve the correlation coefficient value as high as approximately 0.8, or – for different values of parameters – coupling efficiency equal to 0.76.