Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Physics of Fluids

Investigation of alkali vapor diffusion characteristics through microchannels

Yu‐Chi Chen, Shao-Cheng Fang, Hsiu-Hsuan Lin, Jing-Wu Dong, Yi‐Hsin Chen

Published Jun 20, 2022• 2 citations
Publisher

Abstract

We present Rb vapor transport through micro-scale capillaries on the impact of temperature and capillary inner diameters within the limits of the Knudsen number Kn≫1. Daily absorption spectral measurements were taken over several months to evaluate the dynamics of transport. We provide new insight into the diffusion mechanism and observe a quasi-single-layer coating on the surface based on the analysis of a slowly increasing absorption signal. The dwell time of the atom on the glass is directly derived from the diffusion dynamics at different temperatures. According to the mass flow rate, high vapor temperatures caused a faster transport speed, indicating rapid loading in microchannels. We provide a valuable model for future quantum device implementation through the use of miniaturized structures, such as photonic crystal fibers and optical waveguides.

DOI
10.1063/5.0098421

Related papers

Temperature and wall coating dependence of alkali vapor transport speed in micron-scale capillaries

Matthieu Giraud-Carrier, Trevor K. Decker, Joshua S. McClellan +5 more

The impact of storage temperature and wall coatings on alkali vapor transport through micron-scale glass capillaries is analyzed. Glass microbore tubing, chromatography vials, and copper tubing are assembled into closed atomic spectroscopy units with varying capillary lengths and inner diameters. Such devices serve as valuable test models for integrated atomic spectroscopy platforms that rely on hollow-core optical waveguides for chip-scale implementation of quantum coherence phenomena such as slow and stopped light. The inside surface of the systems are coated with dimethyldichlorosilane (DMDCS) after which the system is loaded with rubidium vapor and hermetically sealed. The loaded units are stored in a tube furnace at elevated temperatures and tested daily for absorption over several weeks. Both a wall coating of DMDCS and higher storage temperature increases the transport speed of Rb vapor. The limits and implications of these results are discussed and compared to an expected theoretical model. Suggestions for increasing transport speed are given.

Journal of Vacuum Science & Technology A Vacuum Surfaces and Films•Mar 20, 2017•5 citations

Rubidium diffusion in microscale spectroscopy and slow light platforms

Matthieu Giraud-Carrier, Cameron Hill, Trevor K. Decker +4 more

This paper presents an approach to quantifying the diffusion rate of rubidium in glass microchannels. These types of microchannels are often used in integrated systems (chip and fiber based) which utilize light and rubidium vapor interactions to produce quantum interference phenomena such as slow light. The test platforms reported here were made using glass capillaries connected to larger glass chambers through glassblowing. Rubidium diffusion was monitored in two different ways. First, fluorescence measurements were taken over time at different points down the length of the capillary. Second, optical absorption measurements were taken through the large glass chambers on either side of the capillaries. Results indicate that reaching measurable atomic densities in microscale geometries can take many days or even weeks.

IEEE International Midwest Symposium on Circuits and Systems (MWSCAS)•Aug 1, 2015•1 citation

Nondestructive Monitor and Identification of Interface Atomic Diffusion into Vapor Glass Cell for Quantum Devices

Pengfei Wang, Xixi Huang, Long Ren +8 more

Alkali-metal vapor cells are the core component of atom-based quantum devices, where the chemical speciation and distribution of alkali-metal atoms directly affect device performance. During prolonged operation, these devices experience aging processes in which the accuracy and stability of devices would be degraded due to gradual consumption of metals. Understanding these mechanisms is vital for improving long-term reliability. Traditional routes could quantify the residual alkali-metal, however, failing to distinguish specific consumption pathways such as adsorption on surfaces and diffusion into the glass or coating. Herein, we present a nondestructive Raman spectroscopy-based approach for spatially resolving the distribution and chemical form of alkali-metal atoms inside vapor cells. Using rubidium (Rb) vapor cells as a model, we identify the formation of Rb–silicate compounds and map Rb diffusion profiles within the glass matrix during an accelerated aging process. This method offers a direct and noninvasive means to characterize alkali-metal loss, offering a valuable diagnostic tool for evaluating long-term stability and performance degradation in quantum devices.

ACS Applied Optical Materials•May 2, 2026•0 citations

Perforated Hollow Core Waveguides for Alkali Vapor-cells and Slow Light Devices

Giraud Carrier, Chollet Matthieu

The focus of this work is the integration of alkali vapor atomic vapor cells into common silicon wafer microfabrication processes. Such integrated platforms enable the study of quantum coherence effects such as electromagnetically induced transparency, which can in turn be used to demonstrate slow light. Slow and stopped light devices have applications in the optical communications and quantum computing fields. This project uses hollow core anti-resonant reflecting optical waveguides (ARROWs) to build such slow light devices. An explanation of light-matter interactions and the physics of slow light is first provided, as well as a detailed overview of the fabrication process. Following the discovery of a vapor transport issue, a custom capillary-based testing platform is developed to quantify the effect of confinement, temperature, and wall coatings on rubidium transport. A mathematical model is derived from the experimental results and predicts long transport times. A new design methodology is presented that addresses the transport problem by increasing the number of rubidium entry points. This design also improves chip durability and decreases environmental susceptibility through the use of a single copper reservoir and buried channel waveguides (BCWs). New chips are successfully fabricated, loaded, and monitored for rubidium spectra. Absorption is observed in several chips and absorption peaks depths in excess of 10% are reported. The chip lifetime remains comparable to previous designs. This new design can be expanded to a multi-core platform suitable for slow and stopped light experimentation.

•Jan 1, 2016•0 citations

The effect of temperature on absorbance of rubidium atoms in a vapor glass cell

A Kaewko, P Parkprom, Kittisak Ketaiam +4 more

Abstract Glass cells containing neutral atoms are commonly employed in spectroscopy experiments and have potential applications in metrology. The temperature of the vapor plays a vital role as it directly influences the absorption rate of rubidium atoms. In this research, we study the effect of vapor temperature on the absorption spectrum of rubidium atoms. We observed the broadening of the spectral line and increased absorption, enabling us to determine the absorbance of atoms within the cell. These results provide valuable insights for our future work to characterize absorbance of homemade vapor cells for portable quantum device applications.

Journal of Physics Conference Series•Dec 1, 2023•0 citations

Determination of atomic number density in MEMS vapor cells via single-pass absorption spectroscopy (SPAS)

Sumit Achar, Sinha, Shivam, M Ezhilarasan +2 more

Micro-electro-mechanical systems (MEMS)-based (chip-scale) alkali vapor cells are key components in emerging quantum technologies, where device performance critically depends on the atomic number density. Thus, it is important to have an accurate estimate of the atomic number density in MEMS-based alkali vapor cells to optimize light-matter interactions and design efficient quantum sensing systems. Here, a quantitatively validated method is presented for determining the rubidium (Rb) atomic number density in warm vapor using Single-Pass Absorption Spectroscopy (SPAS). The absolute transmission spectra are measured and modeled using the 780.24~nm and 420.29~nm transitions in Rb-filled MEMS vapor. The theoretical model employs a density-matrix formalism within the Lindblad framework and incorporates directly measurable experimental parameters, such as laser beam power, diameter, and cell temperature. The model explicitly accounts for optical pumping, Doppler broadening, and transit-time broadening effects and exhibits quantitative agreement ($> 99\%$) with experimental spectra over a broad range of temperatures (293-353~K), laser probe powers of approximately 10~$μ$W-100~$μ$W at the 780.24~nm transition and 8~$μ$W-80~$μ$W at the 420.29~nm transition, and cell lengths (2--100~mm). This method demonstrates a practical and reliable approach for determining the density of alkali vapor cells for quantum sensing, metrology, and quantum communication applications.

arXiv:2511.00526•Nov 1, 2025•1 citation
We present Rb vapor transport through micro-scale capillaries on the impact of temperature and capillary inner diameters within the limits of the Knudsen number Kn≫1. Daily absorption spectral measurements were taken over several months to evaluate the dynamics of transport. We provide new insight into the diffusion mechanism and observe a quasi-single-layer coating on the surface based on the analysis of a slowly increasing absorption signal. The dwell time of the atom on the glass is directly derived from the diffusion dynamics at different temperatures. According to the mass flow rate, high vapor temperatures caused a faster transport speed, indicating rapid loading in microchannels. We provide a valuable model for future quantum device implementation through the use of miniaturized structures, such as photonic crystal fibers and optical waveguides.
The impact of storage temperature and wall coatings on alkali vapor transport through micron-scale glass capillaries is analyzed. Glass microbore tubing, chromatography vials, and copper tubing are assembled into closed atomic spectroscopy units with varying capillary lengths and inner diameters. Such devices serve as valuable test models for integrated atomic spectroscopy platforms that rely on hollow-core optical waveguides for chip-scale implementation of quantum coherence phenomena such as slow and stopped light. The inside surface of the systems are coated with dimethyldichlorosilane (DMDCS) after which the system is loaded with rubidium vapor and hermetically sealed. The loaded units are stored in a tube furnace at elevated temperatures and tested daily for absorption over several weeks. Both a wall coating of DMDCS and higher storage temperature increases the transport speed of Rb vapor. The limits and implications of these results are discussed and compared to an expected theoretical model. Suggestions for increasing transport speed are given.
This paper presents an approach to quantifying the diffusion rate of rubidium in glass microchannels. These types of microchannels are often used in integrated systems (chip and fiber based) which utilize light and rubidium vapor interactions to produce quantum interference phenomena such as slow light. The test platforms reported here were made using glass capillaries connected to larger glass chambers through glassblowing. Rubidium diffusion was monitored in two different ways. First, fluorescence measurements were taken over time at different points down the length of the capillary. Second, optical absorption measurements were taken through the large glass chambers on either side of the capillaries. Results indicate that reaching measurable atomic densities in microscale geometries can take many days or even weeks.
Alkali-metal vapor cells are the core component of atom-based quantum devices, where the chemical speciation and distribution of alkali-metal atoms directly affect device performance. During prolonged operation, these devices experience aging processes in which the accuracy and stability of devices would be degraded due to gradual consumption of metals. Understanding these mechanisms is vital for improving long-term reliability. Traditional routes could quantify the residual alkali-metal, however, failing to distinguish specific consumption pathways such as adsorption on surfaces and diffusion into the glass or coating. Herein, we present a nondestructive Raman spectroscopy-based approach for spatially resolving the distribution and chemical form of alkali-metal atoms inside vapor cells. Using rubidium (Rb) vapor cells as a model, we identify the formation of Rb–silicate compounds and map Rb diffusion profiles within the glass matrix during an accelerated aging process. This method offers a direct and noninvasive means to characterize alkali-metal loss, offering a valuable diagnostic tool for evaluating long-term stability and performance degradation in quantum devices.
The focus of this work is the integration of alkali vapor atomic vapor cells into common silicon wafer microfabrication processes. Such integrated platforms enable the study of quantum coherence effects such as electromagnetically induced transparency, which can in turn be used to demonstrate slow light. Slow and stopped light devices have applications in the optical communications and quantum computing fields. This project uses hollow core anti-resonant reflecting optical waveguides (ARROWs) to build such slow light devices. An explanation of light-matter interactions and the physics of slow light is first provided, as well as a detailed overview of the fabrication process. Following the discovery of a vapor transport issue, a custom capillary-based testing platform is developed to quantify the effect of confinement, temperature, and wall coatings on rubidium transport. A mathematical model is derived from the experimental results and predicts long transport times. A new design methodology is presented that addresses the transport problem by increasing the number of rubidium entry points. This design also improves chip durability and decreases environmental susceptibility through the use of a single copper reservoir and buried channel waveguides (BCWs). New chips are successfully fabricated, loaded, and monitored for rubidium spectra. Absorption is observed in several chips and absorption peaks depths in excess of 10% are reported. The chip lifetime remains comparable to previous designs. This new design can be expanded to a multi-core platform suitable for slow and stopped light experimentation.
Abstract Glass cells containing neutral atoms are commonly employed in spectroscopy experiments and have potential applications in metrology. The temperature of the vapor plays a vital role as it directly influences the absorption rate of rubidium atoms. In this research, we study the effect of vapor temperature on the absorption spectrum of rubidium atoms. We observed the broadening of the spectral line and increased absorption, enabling us to determine the absorbance of atoms within the cell. These results provide valuable insights for our future work to characterize absorbance of homemade vapor cells for portable quantum device applications.
Micro-electro-mechanical systems (MEMS)-based (chip-scale) alkali vapor cells are key components in emerging quantum technologies, where device performance critically depends on the atomic number density. Thus, it is important to have an accurate estimate of the atomic number density in MEMS-based alkali vapor cells to optimize light-matter interactions and design efficient quantum sensing systems. Here, a quantitatively validated method is presented for determining the rubidium (Rb) atomic number density in warm vapor using Single-Pass Absorption Spectroscopy (SPAS). The absolute transmission spectra are measured and modeled using the 780.24~nm and 420.29~nm transitions in Rb-filled MEMS vapor. The theoretical model employs a density-matrix formalism within the Lindblad framework and incorporates directly measurable experimental parameters, such as laser beam power, diameter, and cell temperature. The model explicitly accounts for optical pumping, Doppler broadening, and transit-time broadening effects and exhibits quantitative agreement (>99%> 99\%>99%) with experimental spectra over a broad range of temperatures (293-353~K), laser probe powers of approximately 10~μμμW-100~μμμW at the 780.24~nm transition and 8~μμμW-80~μμμW at the 420.29~nm transition, and cell lengths (2--100~mm). This method demonstrates a practical and reliable approach for determining the density of alkali vapor cells for quantum sensing, metrology, and quantum communication applications.